Belkin F5D8233-4 user manual IP Address, Subnet Mask, ISP Gateway Address

Page 33

Alternate Setup Method

Setting your Internet Service Provider (ISP) Connection Type to Static IP

A static IP address connection type is less common than other connection types. If your ISP uses static IP addressing, you will need your IP address, subnet mask, and ISP gateway address. This information is available from your ISP or on the paperwork that your ISP left with you. Type in your information, then click “Apply Changes”

(4). After you apply the changes, the Internet Status indicator will read “connection OK” if your Router is set up properly.

1.IP Address (1)

Provided by your ISP. Enter your IP address here.

2.Subnet Mask (2)

Provided by your ISP. Enter your subnet mask here.

3.ISP Gateway Address (3)

Provided by your ISP. Enter the ISP gateway address here.

1

2

3

4

6	section
5

7

8

9

10

30

Image 33

Contents Wireless Router Page Table of Contents Introduction Advantages of a Wireless NetworkRevolutionary N Wireless Technology with Mimo N Mimo Placement of your N Wireless Router Important Factors for Placement and SetupRouter Placement Choose the Quietest Channel for your Wireless Network Avoid Obstacles and InterferenceCordless Phones Secure Connections, VPNs, and AOL US 877-736-5771 310-898-1100 ext Product Overview Built-In Dynamic Host Configuration Protocol Dhcp Integrated 10/100 4-Port SwitchSetup Assistant Universal Plug and Play UPnPMAC Address Filtering Integrated N Wireless Access PointSetup Assistant Software System Requirements Package ContentsKnowing your Router System RequirementsWireless Security Wireless-Computer StatusWired-Computer Status Router/Power Status Modem StatusInternet Status Connection to Modem Yellow Push Button White Connections to Wired Computers GrayResetting the Router Reset Button RedIi. Restoring the Factory Defaults Power Jack BlackConnecting and Configuring your Router Ethernet USB Setup AssistantModem Requirements Hardware Connections Follow the Quick Installation Guide QIG Set Up the Router Run the Setup Assistant Software Connecting and Configuring your RouterChecking Settings Confirmation ScreenProgress Screen Connecting and Configuring your Router Requesting Internet Account Info if needed Troubleshooting Connecting and Configuring your Router Hardware Connections Follow Quick Installation Guide QIG Alternate Setup MethodLogging into the Router Logging out of the RouterUnderstanding the Web-Based Advanced User Interface Quick-Navigation Links Login/Logout ButtonHome Button Help ButtonLAN Settings Internet-Status IndicatorInternet Settings FeaturesAlternate Setup Method Setting your Connection Type Change WAN MAC Address Host NameIP Address Subnet MaskISP Gateway Address Setting your ISP Connection Type to PPPoE Service Name PasswordUser Name MTUService IP Address Pptp PasswordPptp Account My IP AddressMy Subnet Mask Default GatewaySelect your State Setting Custom Domain Name Server DNS Settings User Decide Login Server ManuallyConfiguring your WAN Media Access Controller MAC Address Cloning your MAC AddressEntering a Specific MAC Address Viewing the LAN Settings Using the Web-Based Advanced User InterfaceChanging LAN Settings Using the Web-Based Advanced User InterfaceIP Pool Dhcp ServerLease Time Local Domain NameViewing the Dhcp Client List Configuring the Wireless Network SettingsChanging the Wireless Network Name Ssid Changing the Wireless Channel Using the Wireless Mode SwitchExtension Channel Using the Bandwidth Switch 20MHz only20MHz/40MHz Auto Using the Broadcast Ssid Feature Protected Mode Switch 802.11e/WMM QoS SwitchChanging the Wireless Security Settings WPA2 Requirements Setting WPA/WPA2-Personal PSK Setting WPA Security Setting WPA-PSK Setting WEP Encryption Using a Hexadecimal Key Using the Access Point Mode Setting MAC Address Control Setting up a Deny Access List Setting up an Allow Access ListConfiguring the Firewall Configuring Internal Forwarding Settings Manually Entering Settings into the Virtual ServerChoosing an Application Setting Client IP Filters Enabling the Demilitarized Zone DMZ Setting up the Router’s Dynamic DNS Update Client Using Dynamic DNSBlocking an Icmp Ping UtilitiesRestarting the Router Restarting the Router to Restore Normal OperationRestoring Factory Default Settings Saving a Current Configuration Restoring a Previous Configuration Using the Web-Based Advanced User Interface Checking for a New Version of Firmware Updating the FirmwareDownloading a New Version of Firmware Updating the Router’s Firmware Using the Web-Based Advanced User Interface Changing System Settings Setting or Changing the Administrator PasswordChanging the Login Time-Out Setting Enabling Remote Management Setting the Time and Time ZoneEnabling/Disabling NAT Network Address Translation Enabling/Disabling UPnP Enabling/Disabling Auto Firmware UpdateManually Configuring Network Settings in Mac OS up to Manually Configuring Network SettingsManually Configuring Network Adapters in Mac OS Manually Configuring Network SettingsSection Manually Configuring Network Settings Manually Configuring Network Adapters in Windows 98SE or Me Microsoft Internet Explorer 4.0 or Higher Recommended Web Browser SettingsNetscape Navigator 4.0 or Higher Troubleshooting Setup Assistant CD does not automatically startSetup Assistant cannot find my Router Setup Assistant cannot connect my Router to the Internet Troubleshooting Section Troubleshooting Can’t connect to the Internet wirelessly Troubleshooting Troubleshooting C3030FAF4BB2C3D44BC3D4E7E4 = 128-bit key Click OK, and then Apply to save the settings Do Belkin products support WPA/WPA2? Troubleshooting XP WPA What’s the difference between 802.11g and draft 802.11n? Belkin Wireless Comparison Chart Technical Support Information FCC StatementFederal Communications Commission Notice Canada-Industry Canada IC ModificationsWhat is not covered by this warranty? What will we do to correct problems?How to get service What the period of coverage isHow state law relates to the warranty Wireless Router