Belkin F5D8233-4 user manual My Subnet Mask, Default Gateway

Page 37

Alternate Setup Method

6.My Subnet Mask

Provided by your ISP. Enter the IP address here.

7.Default Gateway

Provided by your ISP. If your ISP did not give you a connection ID (default gateway), leave this blank.

8.Disconnect after X....

The “Disconnect” feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time. For instance, placing a check mark next to this option and entering “5” into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity. This option should be used if you pay for your Internet service by the minute.

1

2

3

4

6

section

5

 

7

8

9

10

34

Image 37
Contents Wireless Router Page Table of Contents Introduction Advantages of a Wireless NetworkRevolutionary N Wireless Technology with Mimo N Mimo Important Factors for Placement and Setup Placement of your N Wireless RouterRouter Placement Avoid Obstacles and Interference Choose the Quietest Channel for your Wireless NetworkCordless Phones Secure Connections, VPNs, and AOL US 877-736-5771 310-898-1100 ext Product Overview Built-In Dynamic Host Configuration Protocol Dhcp Integrated 10/100 4-Port SwitchSetup Assistant Universal Plug and Play UPnPMAC Address Filtering Integrated N Wireless Access PointSetup Assistant Software System Requirements Package ContentsKnowing your Router System RequirementsWireless-Computer Status Wireless SecurityWired-Computer Status Modem Status Router/Power StatusInternet Status Connection to Modem Yellow Push Button White Connections to Wired Computers GrayResetting the Router Reset Button RedIi. Restoring the Factory Defaults Power Jack BlackEthernet USB Setup Assistant Connecting and Configuring your RouterModem Requirements Hardware Connections Follow the Quick Installation Guide QIG Set Up the Router Run the Setup Assistant Software Connecting and Configuring your RouterConfirmation Screen Checking SettingsProgress Screen Connecting and Configuring your Router Requesting Internet Account Info if needed Troubleshooting Connecting and Configuring your Router Hardware Connections Follow Quick Installation Guide QIG Alternate Setup MethodLogging out of the Router Logging into the RouterUnderstanding the Web-Based Advanced User Interface Quick-Navigation Links Login/Logout ButtonHome Button Help ButtonLAN Settings Internet-Status IndicatorInternet Settings FeaturesAlternate Setup Method Setting your Connection Type Change WAN MAC Address Host NameSubnet Mask IP AddressISP Gateway Address Setting your ISP Connection Type to PPPoE Service Name PasswordUser Name MTUService IP Address Pptp PasswordPptp Account My IP AddressMy Subnet Mask Default GatewaySelect your State Setting Custom Domain Name Server DNS Settings User Decide Login Server ManuallyCloning your MAC Address Configuring your WAN Media Access Controller MAC AddressEntering a Specific MAC Address Viewing the LAN Settings Using the Web-Based Advanced User InterfaceChanging LAN Settings Using the Web-Based Advanced User InterfaceIP Pool Dhcp ServerLease Time Local Domain NameViewing the Dhcp Client List Configuring the Wireless Network SettingsChanging the Wireless Network Name Ssid Using the Wireless Mode Switch Changing the Wireless ChannelExtension Channel 20MHz only Using the Bandwidth Switch20MHz/40MHz Auto 802.11e/WMM QoS Switch Using the Broadcast Ssid Feature Protected Mode SwitchChanging the Wireless Security Settings WPA2 Requirements Setting WPA/WPA2-Personal PSK Setting WPA Security Setting WPA-PSK Setting WEP Encryption Using a Hexadecimal Key Using the Access Point Mode Setting MAC Address Control Setting up a Deny Access List Setting up an Allow Access ListConfiguring the Firewall Manually Entering Settings into the Virtual Server Configuring Internal Forwarding SettingsChoosing an Application Setting Client IP Filters Enabling the Demilitarized Zone DMZ Setting up the Router’s Dynamic DNS Update Client Using Dynamic DNSBlocking an Icmp Ping UtilitiesRestarting the Router Restarting the Router to Restore Normal OperationRestoring Factory Default Settings Saving a Current Configuration Restoring a Previous Configuration Using the Web-Based Advanced User Interface Checking for a New Version of Firmware Updating the FirmwareDownloading a New Version of Firmware Updating the Router’s Firmware Using the Web-Based Advanced User Interface Setting or Changing the Administrator Password Changing System SettingsChanging the Login Time-Out Setting Enabling Remote Management Setting the Time and Time ZoneEnabling/Disabling NAT Network Address Translation Enabling/Disabling UPnP Enabling/Disabling Auto Firmware UpdateManually Configuring Network Settings in Mac OS up to Manually Configuring Network SettingsManually Configuring Network Adapters in Mac OS Manually Configuring Network SettingsSection Manually Configuring Network Settings Manually Configuring Network Adapters in Windows 98SE or Me Microsoft Internet Explorer 4.0 or Higher Recommended Web Browser SettingsNetscape Navigator 4.0 or Higher Setup Assistant CD does not automatically start TroubleshootingSetup Assistant cannot find my Router Setup Assistant cannot connect my Router to the Internet Troubleshooting Section Troubleshooting Can’t connect to the Internet wirelessly Troubleshooting Troubleshooting C3030FAF4BB2C3D44BC3D4E7E4 = 128-bit key Click OK, and then Apply to save the settings Do Belkin products support WPA/WPA2? Troubleshooting XP WPA What’s the difference between 802.11g and draft 802.11n? Belkin Wireless Comparison Chart Technical Support FCC Statement InformationFederal Communications Commission Notice Canada-Industry Canada IC ModificationsWhat is not covered by this warranty? What will we do to correct problems?How to get service What the period of coverage isHow state law relates to the warranty Wireless Router