Star Micronics SP300 Series manual Connectors and Signals, RS-232C

Page 14

2-3. Connectors and Signals

RS-232C

	Pin no.	Signal name			I/O	Function
	Pin no.	Signal name			direction	Function
					direction
	1		F-GND		—	Frame ground
	2		TXD		OUT	Transmitted data
	3		RXD		IN	Received data
	4		RTS		OUT	Data transmission request signal. This is al-
						ways “SPACE” when the printer is turned on.
	5		CTS		IN	This signal changes to “SPACE” when
						host computer is ready to transmit data. (In
						this instance, the printer does not check this
						signal.)
	6		N/C			Not connected
	7		S-GND		—	Signal ground
	8		N/C			Not connected
	9-10		N/C			This pin is used when using the optional
						interface board.
	11		RCH		OUT	This signal changes to “SPACE” when the
						printer is ready to receive data. (The signal
						line is same as pin 20.)
	12		N/C			Not connected.
	13		S-GND		—	Signal ground
	14				OUT	When printer error occurs (such as paper
	14		FAULT		OUT	When printer error occurs (such as paper
						out, mechanical error, etc.), this signal is
						set to “MARK”.
	15	Multi-printer TXD			OUT	Diode coupled TXD
	16	Multi-printer DTR			OUT	Diode coupled DTR
	17 to 19		N/C			This pin is used when using the optional
						interface board.
	20		DTR		OUT	Data terminal ready signal. When the printer
						is ready to receive data, this signal changes
						to “SPACE”.
	21-22		N/C			Not connected
	23 to 25		N/C			This pin is used when using the optional
						interface board.
		14				25
		1				13

Fig. 2-4 Serial interface connector

– 10 –

Image 14

Contents Dot Matrix Printer SP300 Series Programmer’s Manual Page Table of Contents IBM Character Set #1 DIP SW2-1 OFF, SW2-2 on LED flashes Validation printing mode is set Basic OperationSwitch Operation Combined Switch Operation Self Print TestMicro Feed Feed + on Line + Power on Page Page Selectable. Refer to Installation Interface SpecificationsTo Installation Manual Parity bit Odd, even or noneInput RXD, CTS Output DTR, FAULT, TXD, RCH, RTSInterface Circuit Input TTY-RXD, TTY-RXDRInput RD, RS Output SD, CSConnectors and Signals RS-232CMA current loop option RS-422A optionInterface Connections Example of interface connections for IBM PCInstalling the Optional Interface Board Installing the optional interface boardDTR mode Data StructureDTR Mark DTR Space ON/X-OFF mode This mode accessed when the DIP switch 3-5 is OFFOFF Status STX-ETX mode Page STX-ETX mode flow diagram for host computer Pulses Handshaking Busy signalsInterface Timing Logic level Compatible with TTL levelTypical interface circuit This connector mates with an Amphenol 57-30360 connectorEmergency Suspension Operating Method This printer can print one line of validation printingOther Printing FormatData format GS data LFAuto cutting control codes Cutting MethodCutting position Other position to be observedControl Codes Used for Character Setting Control Codes Used for Line SpacingControl Codes Used for Download Characters Control Codes Used for Page LayoutControl Code Used for Graphics Printing Control Codes Used for Peripheral Units Other Control CodesFunction Function Function Function Control Codes Used for Line Spacing Set 1/8-inch line feed ESC 0 1BH 30H Sets page length at n inchesSet vertical tab positions Left end Printing area Left margin n Right margin n columns Set horizontal tab position Control Codes Used for Graphics Printing Set n/216-inch line feed simulation ESC 3 n 1BH 33H n Example Printing Possible Code Outline When the 5 × 9 font is set Definition of download charactersCode Outline Example Example of transmitting data 10 × n1 ms 10 × n2 ms Printing and paper feed are prohibited Other Control Codes Function Initialize printer ESC @ 1BH 40H ETX 03HFunction Character Code Tables U.S.A. & Europe DIP SW2-1 ON, SW2-2 onPage IBM Character Set #1 DIP SW2-1 OFF, SW2-2 on Page IBM Character Set #2 DIP SW2-1 ON, SW2-2 OFF Page Japan DIP SW2-1, OFF, SW2-2 OFF Page International Character Sets Memo Page Overseas Subsidiary Companies Star Micronics AMERICA, INC