Star Micronics SP300 Series manual Code Outline

Page 49

FUNCTION

CODE

OUTLINE

NOTE

FUNCTION

CODE

OUTLINE

Select vertical expaned character mode

<ESC> “h” “1” or <ESC> “h” <1>

(1B)H (68)H (31)H or (1B)H (68)H (01)H

Prints characters two times the normal vertical size after the code is received.

However, the bit image mode <ESC> “K” and <ESC> “L” are excluded.

(1)When combined with the <SO> code, this code enables printing of the characters in two times the normal vertical and horizontal size.

(2)This code is not combined with the inverted print mode <SI> code.

(3)For the 6 × 12 dots IBM block graphic (the characters code table (B0)H-(DF)Hand (F4)H-(F5)Hof IBM charac- ter set #1 and #2) of the font construction, vertical enlargement is not available.

(4)The relationship of the vertically enlarged character and the normal character is matched at the lower level.

(5)Feed the paper a minimum of one line before printing with this code.

Cancel vertical expanded character mode

<ESC> “h” “0” or <ESC> “h” <0>

(1B)H (68)H (30)H or (1B)H (68)H (00)H

Cancels vertical expanded character mode

– 45 –

Image 49
Contents Dot Matrix Printer SP300 Series Programmer’s Manual Page Table of Contents IBM Character Set #1 DIP SW2-1 OFF, SW2-2 on Basic Operation LED flashes Validation printing mode is setSelf Print Test Switch Operation Combined Switch OperationMicro Feed Feed + on Line + Power on Page Page To Installation Manual Interface SpecificationsSelectable. Refer to Installation Parity bit Odd, even or noneInterface Circuit Output DTR, FAULT, TXD, RCH, RTSInput RXD, CTS Input TTY-RXD, TTY-RXDROutput SD, CS Input RD, RSRS-232C Connectors and SignalsRS-422A option MA current loop optionExample of interface connections for IBM PC Interface ConnectionsInstalling the optional interface board Installing the Optional Interface BoardData Structure DTR modeDTR Mark DTR Space This mode accessed when the DIP switch 3-5 is OFF ON/X-OFF modeOFF Status STX-ETX mode Page STX-ETX mode flow diagram for host computer Interface Timing Handshaking Busy signalsPulses Logic level Compatible with TTL levelTypical interface circuit Amphenol 57-30360 connector This connector mates with anEmergency Suspension This printer can print one line of validation printing Operating MethodData format Printing FormatOther GS data LFCutting position Cutting MethodAuto cutting control codes Other position to be observedControl Codes Used for Line Spacing Control Codes Used for Character SettingControl Code Used for Graphics Printing Control Codes Used for Page LayoutControl Codes Used for Download Characters Other Control Codes Control Codes Used for Peripheral UnitsFunction Function Function Function Control Codes Used for Line Spacing Sets page length at n inches Set 1/8-inch line feed ESC 0 1BH 30HSet vertical tab positions Left end Printing area Left margin n Right margin n columns Set horizontal tab position Control Codes Used for Graphics Printing Set n/216-inch line feed simulation ESC 3 n 1BH 33H n Example Printing Possible Code Outline Definition of download characters When the 5 × 9 font is setCode Outline Example Example of transmitting data 10 × n1 ms 10 × n2 ms Printing and paper feed are prohibited Other Control Codes Function Initialize printer ESC @ 1BH 40H 03H ETXFunction U.S.A. & Europe DIP SW2-1 ON, SW2-2 on Character Code TablesPage IBM Character Set #1 DIP SW2-1 OFF, SW2-2 on Page IBM Character Set #2 DIP SW2-1 ON, SW2-2 OFF Page Japan DIP SW2-1, OFF, SW2-2 OFF Page International Character Sets Memo Page Overseas Subsidiary Companies Star Micronics AMERICA, INC