Star Micronics LC-8021 manual Switches 1, 2 Top and bottom margins, Switch 4 Control code FF

Page 39

EDS-2 Settings 33

BANK C

Switches 1, 2: Top and bottom margins

Use these switches to specify the top and bottom margins for printing.

	Switch	Setting	Meaning

	SW1	ON	1/6″ top margin for cut-sheet paper

		OFF	0″ top margin for cut-sheet paper
		OFF	0″ top margin for cut-sheet paper

	SW2	ON	1/6″ bottom margin for cut-sheet paper

		OFF	0″ bottom margin for cut-sheet paper
		OFF	0″ bottom margin for cut-sheet paper

Switch 3: Head gap sensing for on each line

Specifies whether head gap sensing for on each line should be enabled (OFF) or disabled (ON).

Switch 4: Control code FF

Control code FF (hexadecimal code 0C):

Specifies whether to eject paper (ON) or form feed (OFF).

Switches 5, 6: Waiting period for paper loading

Waiting Period	SW5	SW6

2.0 seconds	ON	ON

1.5 seconds	OFF	ON

1.0 seconds	ON	OFF

0.5 seconds	OFF	OFF

Image 39

Contents LC-8021 Trademark acknowledgments Chapter About this manualContents Appendix a Troubleshooting Using the EDS ModeUsing the Printer with MS-DOS Optional AccessoriesPage Choosing a place for the printer Printer SetupUnpacking the printer General guide Removing the front cover Opening the front coverRemoving the protective materials Installing the ribbon cartridge Page Removing the ribbon cartridge Connecting to a power outlet and turning power on and off Connecting to a power outlet and turning power on and offLoading paper Connecting to your computer Connecting to your computerTo connect with a parallel cable To connect with a serial cable Printer Setup Control Panel Operations Switching between on-line and off-linePaper eject Selecting a fontLine feed Form feedChanging the auto load position Entering the Multi-part Mode Clearing the printer’s bufferInitializing the printer Using the EDS Mode About EDS Mode settingsEntering the EDS Mode Selecting a bank Using the EDS ModeExiting the EDS Mode Selecting a switchChanging a switch setting Printing the current switch settingsSwitch 4 RAM Usage EDS-1 SettingsSwitch 1 Emulation Switch 2 Not used Switch 3 Character TableSwitch 4 Auto LF with CR Switch 6 Multi-Part ModeSwitch 1 Graphics Direction Switch 2 Not used Switch 3 Line SpacingSwitches 3, 4, 5 Print Pitch Switches 1, 2 Print ModeSwitches 1, 2, 3, 4 Page Length Switch 5 Cut-sheet eject directionSwitch 6 Skew sensor for cut-sheet paper Bank E Name Country Remarks Russia Preferred by Microsoft International Bank F Switches 1, 2, 3, 4, 5, 6 LQ Font SelectionSwitch 3 Parity EDS-2 SettingsSwitch 1 Data Length Switch 2 Parity CheckSwitches 4, 5, 6 Not used Switch 4 ProtocolSwitches 5, 6 Not used Switch 1, 2, 3 Baud RateSwitches 5, 6 Waiting period for paper loading Switches 1, 2 Top and bottom marginsSwitch 3 Head gap sensing for on each line Switch 4 Control code FFSetting up for printing with MS-DOS Using the Printer with MS-DOSPassbook Paper HandlingSelecting paper types Cut-Sheet PaperFeeding a passbook into the printer Feeding cut-sheet paper into the printer Print area Serial Interface Unit IS-NP192 Optional AccessoriesSerial-to-Parallel Interface Converter SPC-8K Appendix a Troubleshooting Short testLong test Hexadecimal dump Adjusting the dot alignmentAdjusting the dot alignment Problem Possible Cause Troubleshooting guideTroubleshooting guide Forms are smudged Ribbon is jammed Make sure that the ribbon Right during printing Character set is selected Mode LPT1=COM1 or Mode LPT1=COM2 Checking system software settings in MS-DOSPrinting Speed Pitch Draft cps/dpi Appendix B SpeciﬁcationsEmulation Appendix C Interface Pin Outs Parallel InterfaceSerial Interface Standard Italic Character Set International Character Set Appendix D Character SetsCharacter Sets Code Page #861 Icelandic IBM Special Character SetCode Page #860 Portuguese Code Page #850 Multi-lingualCode Page #3840 IBM-Russian Code Page #863 Canadian FrenchCode Page #866 Russian Code Page #865 NordicCode Page #3845 Hungarian Code Page #3841 Gost-RussianCode Page #3844 Code Page #3843 PolishCode Page #852 Latin-2 Code Page #3846 TurkishCode Page #3848 Brazil-ABICOMP Code Page #3847 Brazil-ABNTCode Page #851 Greek Code Page #1001 Arabic Code Page #737 GreekCode Page #772 Lithuanian Code Page #869 GreekCode Page #2001 Lithuanian-KBL Code Page #928 GreekCode Page #3011 Latvian1 Code Page #774 LithuanianCode Page #3002 Estonian2 Code Page #3001 Estonian1Code Page #3041 Maltese Code Page #3012 Latvian2Code Page #3031 Hebrew Code Page #3021 BulgarianCode Page #3863 Code Page #3850 Standard KUCode Page #3861 Microwiz KU Code Page #3860 Rajvitee KUCode Page #3865 Newsic TIS Code Page #3864 Popular TISAppendix E Printer Control Codes Standard ModePrinter Control Codes Select 1/8″ line spacing Denmark OCR-B Set left margin IBM Mode Select print pitch and download Set base unit of line spacing Appendix F Glossary Multi Eject On Line Part Appendix G Control Panel Operation GuideAUTOEXEC.BAT 47 MS-DOS Page