Star Micronics LC-8021 manual Emulation

Page 57

51

Paper

Cut-sheet

 

 

Paper width:

3″ to 8.3″ / 76.2 to 210 mm

 

Paper length:

2.5″ to 11.7″ / 63.5 to 297 mm

 

Paper thickness:

0.0028″ to 0.0071″ / 0.07 to 0.18 mm (1-ply)

 

 

0.0028″ to 0.014″ / 0.07 to 0.35 mm (multi-ply)

 

Paper weight:

14 to 42 lbs. / 52 to 156 g/m2 / 45 to 135 kg (1-ply)

 

 

11 to 14 lbs. / 40 to 52 g/m2 / 34 to 45 kg (multi-ply)

 

Copy capability

Normal mode:

 

 

Original + 0-2 copies (Total thickness: Max. 0.25 mm)

 

 

Multi-part mode:

 

 

Original + 3-4 copies (Total thickness: Max. 0.35 mm)

 

Pass book

 

 

Paper width:

4″ to 6″ / 101.6 to 152.4 mm

 

Paper length:

5″ to 8″ / 127 to 203.2 mm

 

Total paper thickness:

2 mm (max.)

 

Number of pages:

14 excluding cover

Emulation

Standard Mode:

EPSON ESC/P (24-pin)

 

NEC Graphic Compatible

 

 

IBM Mode:

Proprinter XL24E

Interfaces

Standard:

Centronics parallel and RS-232 (dual interface)

 

Option:

Dual serial interface

Ribbon Type

On-carriage, dedicated

 

 

Monochrome: Black only

 

 

P24 (Standard)

 

Ribbon Life

P24: 2 million characters (ASCII draft)

Dimensions and Weight

Width:

16.1″ / 410 mm

 

Depth:

12.6″ / 320 mm

 

Height:

7.66″ / 194.5 mm

 

Weight:

18.94 lbs. / 8.6 kg

Power Supply

220V AC ±10%; 50/60Hz

 

Power Consumption

13W during stand-by

 

 

55W during ASCII draft printing

Options

SPC-8K Serial-To-Parallel Converter

 

IS-NP192 Serial Interface Unit

 

 

P24 Refill Ribbon

 

Page 56 Page 58
Image 57
Page 56 Page 58
Contents LC-8021 Trademark acknowledgments Chapter About this manualContents Using the Printer with MS-DOS Using the EDS ModeOptional Accessories Appendix a TroubleshootingPage Choosing a place for the printer Printer SetupUnpacking the printer General guide Removing the front cover Opening the front coverRemoving the protective materials Installing the ribbon cartridge Page Removing the ribbon cartridge Connecting to a power outlet and turning power on and off Connecting to a power outlet and turning power on and offLoading paper Connecting to your computer Connecting to your computerTo connect with a parallel cable To connect with a serial cable Printer Setup Control Panel Operations Switching between on-line and off-lineLine feed Selecting a fontForm feed Paper ejectChanging the auto load position Entering the Multi-part Mode Clearing the printer’s bufferInitializing the printer Using the EDS Mode About EDS Mode settingsEntering the EDS Mode Selecting a bank Using the EDS ModeChanging a switch setting Selecting a switchPrinting the current switch settings Exiting the EDS ModeSwitch 1 Emulation EDS-1 SettingsSwitch 2 Not used Switch 3 Character Table Switch 4 RAM UsageSwitch 1 Graphics Direction Switch 6 Multi-Part ModeSwitch 2 Not used Switch 3 Line Spacing Switch 4 Auto LF with CRSwitches 3, 4, 5 Print Pitch Switches 1, 2 Print ModeSwitches 1, 2, 3, 4 Page Length Switch 5 Cut-sheet eject directionSwitch 6 Skew sensor for cut-sheet paper Bank E Name Country Remarks Russia Preferred by Microsoft International Bank F Switches 1, 2, 3, 4, 5, 6 LQ Font SelectionSwitch 1 Data Length EDS-2 SettingsSwitch 2 Parity Check Switch 3 ParitySwitches 5, 6 Not used Switch 4 ProtocolSwitch 1, 2, 3 Baud Rate Switches 4, 5, 6 Not usedSwitch 3 Head gap sensing for on each line Switches 1, 2 Top and bottom marginsSwitch 4 Control code FF Switches 5, 6 Waiting period for paper loadingSetting up for printing with MS-DOS Using the Printer with MS-DOSSelecting paper types Paper HandlingCut-Sheet Paper PassbookFeeding a passbook into the printer Feeding cut-sheet paper into the printer Print area Serial Interface Unit IS-NP192 Optional AccessoriesSerial-to-Parallel Interface Converter SPC-8K Appendix a Troubleshooting Short testLong test Hexadecimal dump Adjusting the dot alignmentAdjusting the dot alignment Problem Possible Cause Troubleshooting guideTroubleshooting guide Forms are smudged Ribbon is jammed Make sure that the ribbon Right during printing Character set is selected Mode LPT1=COM1 or Mode LPT1=COM2 Checking system software settings in MS-DOSPrinting Speed Pitch Draft cps/dpi Appendix B SpecificationsEmulation Appendix C Interface Pin Outs Parallel InterfaceSerial Interface Standard Italic Character Set International Character Set Appendix D Character SetsCharacter Sets Code Page #860 Portuguese IBM Special Character SetCode Page #850 Multi-lingual Code Page #861 IcelandicCode Page #866 Russian Code Page #863 Canadian FrenchCode Page #865 Nordic Code Page #3840 IBM-RussianCode Page #3844 Code Page #3841 Gost-RussianCode Page #3843 Polish Code Page #3845 HungarianCode Page #3848 Brazil-ABICOMP Code Page #3846 TurkishCode Page #3847 Brazil-ABNT Code Page #852 Latin-2Code Page #851 Greek Code Page #1001 Arabic Code Page #737 GreekCode Page #2001 Lithuanian-KBL Code Page #869 GreekCode Page #928 Greek Code Page #772 LithuanianCode Page #3002 Estonian2 Code Page #774 LithuanianCode Page #3001 Estonian1 Code Page #3011 Latvian1Code Page #3031 Hebrew Code Page #3012 Latvian2Code Page #3021 Bulgarian Code Page #3041 MalteseCode Page #3861 Microwiz KU Code Page #3850 Standard KUCode Page #3860 Rajvitee KU Code Page #3863Code Page #3865 Newsic TIS Code Page #3864 Popular TISAppendix E Printer Control Codes Standard ModePrinter Control Codes Select 1/8″ line spacing Denmark OCR-B Set left margin IBM Mode Select print pitch and download Set base unit of line spacing Appendix F Glossary Multi Eject On Line Part Appendix G Control Panel Operation GuideAUTOEXEC.BAT 47 MS-DOS Page
Top Page Image Contents