Transition Networks TN-GLC-BX-U, TN-CWDM-SFP-1xx0 Installation, Installing the SFP transceiver

TN-GLC-xx-xx SFPs

Part Number	Port Description
TN-GLC-BX-U	1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx,
	single mode, single fiber 10 km (6.2 miles)*
TN-GLC-BX-D	1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx,
	single mode, single fiber 10 km (6.2 miles)*
TN-GLC-BX-U-40	1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx,
	single mode, single fiber 40 km (24.9 miles)*
TN-GLC-BX-D-40	1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx,
	single mode, single fiber 40 km (24.9 miles)*
TN-GLC-BX-U-60	1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx,
	single mode, single fiber 60 km (37.3 miles)*
TN-GLC-BX-D-60	1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx,
	single mode, single fiber 60 km (37.3 miles)*
TN-GLC-FE-100BX-U	100Base-BX, Simplex LC 1310 nm Tx/1550 nm Rx,
	single mode, single fiber 20 km (12.4 miles)*
TN-GLC-FE-100BX-D	100Base-BX, Simplex LC 1550 nm Tx/1310 nm Rx ,
	single mode, single fiber 20 km (12.4 miles)*
TN-GLC-FE-100FX	100Base-BX, Duplex LC 1300 nm, multimode
	2 km (1.2 miles)*
TN-GLC-FE-100LX	100Base-BX, Duplex LC 1310 nm, single mode
	20 km (12.4 miles)*
TN-GLC-GE-100FX***	100Base-BX, Duplex LC 1300 nm, multimode
	2 km (1.2 miles)*
TN-GLC-ZX-SM	1000Base-LX, 1550 nm, single mode
	80 km (49.7 miles)*
TN-CWDM-SFP-1xx0	1000Base-LX, single mode
	80 km (49.7 miles)*

xx= center wavelength (λc) (See technical specifications for more details.)

27	=1270nm	39 = 1390nm	53 = 1530nm
29	= 1290nm	41 = 1410nm	55 = 1550nm
31	= 1310nm	43 = 1430nm	57 = 1570nm
33	= 1330nm	47 = 1470nm	59 = 1590nm
35	= 1350nm	49 = 1490nm	61 = 1610nm
37	= 1370nm	51 = 1510nm

*Unless otherwise indicated, the distances listed are the typical maximum cable distance. The actual maximum cable distances are dependent upon the physical characteristics of the network installation.

**Transition Networks' SFP modules fully comply with the Multi-Sourcing Agreement (MSA). This compliance allows our SFP modules to be used in other MSA compliant SFP platforms without problems. In addition, TN SFP modules are also compatible with all Cisco SFP-based routers and switches, as well as its IOS software. TN SFP modules ARE NOT Cisco OEM brand modules.

***Provide 100Base-FX interface when plugged into a gigabit SFP slot on Cisco catalyst 3750, 3560, and 2970 series switches.

Note: Install simplex or single fiber SFP models in pairs in the same network where one is the local SFP and the other is the remote SFP.

Installation

Installing the SFP transceiver

To install the SFP module into a network switches media converter, do the following:

1.Position the module at the installation slot so that the label faces up.

2.Carefully slide the module into the installation slot, aligning it with the internal installation guides.

Installing copper cables

1.Locate or build 1000Base-T compliant copper cables with male, RJ-45 connectors installed at both ends.

2.Connect the RJ-45 connector at one end of the cable to the RJ-45 port on the media converter.

3.Connect the RJ-45 connector at the other end of the cable to the RJ-45 port on the other device.

RJ-45 port	RJ-45 port
on the media	on the other device
converter	(switch, work station, etc.)

2 Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600—24 hours techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 3