Transition Networks SCSCF30XX-10X Cable Specifications Troubleshooting, Technical Specifications

SCSCF30xx-10x

Cable Specifications -- Continued

Troubleshooting

SCSCF3029-102

SCSCF3029-103

Fiber-optic Transmitter Power:

Fiber-optic Receiver Sensitivity:

Link Budget:

CSCSCF3039-100

Fiber-optic Transmitter Power:

Fiber-optic Receiver Sensitivity:

Link Budget:

1310 nm (TX) / 1550 nm (RX) simplex

1550 nm (TX) / 1310 nm (RX) simplex

min: -8.0 dBm	max: -3.0 dBm
min: -33.0 dBm	max: -3.0 dBm
25.0 dB
1300 nm multimode
min: -19.0 dBm	max: -14.0 dBm
min: -30.0 dBm	max: -14.0 dBm
11.0 dB

If the Device fails, isolate and correct the failure by determining the answers to the following questions and then taking the indicated action:

1.	Is the PWR (Power) LED on the Device illuminated?
	NO
	• Ensure that the power adapter is the proper type of voltage and cycle
	frequency for the outlet.
	• Ensure the power adapter is properly installed in the Device and in the
	grounded outlet.

The fiber optic transmitters on this device meet Class I Laser safety requirements per IEC-825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.

Technical Specifications

For use with Transition Networks Model SCSCF30xx-10x or equivalent

Standards	FCC Class A; EN 55022 Class A; EN 55024; ANSI
	T1.102-1993; ETSI TBR-24; ITU-T G.703 G.823 for jitter
	tolerance; G.775 for loss of signal; Telecordia GR-
	499CORE & GR-253-CORE
Data Rate	DS3 / T3 = 44.7 Mb/s; E3 = 34.4 Mb/s
Dimensions	3.25" x 4.7" x 1.0" (83 mm x 119 mm x 25 mm)
Weight	10 oz. (283 g) approximately
Power Consumption	6.0 Watts
Power Supply	12 VDC, 0.8 Amp (minimum)
DC Outlet	Minimum output regulation: 5%
MTBF (stand alone)	48,996 (MIL217F2 V5.0) (MIL-HDBD-217F)
	119,854 (Bellcore7 V5.0)
Environment	Tmra*:	0 to 50°C (32° to 122°F )
	Storage Temp:	-20° to 85°C (-4° to 185°F)
	Humidity:	5 to 95%, non condensing
	Altitude:	0 to 10,000 feet
Warranty	Lifetime

*Manufacturer’s rated ambient temperature.

For the most up-to-date information on the SCSCF30xx-10x Device, view the user’s guide on-line at www.transition.com.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J applicable at the date of manufacture.

CAUTION: Visible and invisible laser radiation when open. Do not stare into beam or view directly with optical instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

	•	Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
	YES
	•	Proceed to step 2.
2.	Is the SDC (Signal Detect / Coax) LED illuminated green?
	NO
	•	Check the coax cables for the proper connection.
	•	Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
	YES
	•	Proceed to step 3.
3.	Is the SDF (Signal Detect / Fiber) LED illuminated green?
	NO
	•	Check the fiber cables for proper connection.
	•	Verify that the TX and RX cables on the local Device are connected to
		the RX and TX ports, respectively, on the remote Device.
	•	Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
	YES
	•	Proceed to step 4.
4.	Is the SDC (Signal Detect / Coax) LED flashing green?
	YES
	•	The coax link is in loop-back mode. For normal operation, set the loop-
		back switch to the center (normal) position.
	•	Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
	NO
	•	Proceed to step 5.
5.	Is the SDF (Signal Detect / Fiber) LED flashing green?
	YES
	•	The fiber link is in loop-back mode. For normal operation, set the loop-
		back switch to the center (normal) position.
	•	Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
	NO
	•	Proceed to step 6.

8 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 9