Transition Networks MIL-SM2401MAF manual FastEthernet 1/2, Flowcontrol on, Security on

Page 28

Transition Networks

 

 

 

MIL-SM2401MAF

 

 

 

 

 

 

 

Use the speed

 

 

 

 

configuration

 

 

 

 

command to specify

 

 

 

 

the speed mode of

 

 

 

 

operation for module

 

Switch (config)#

 

 

Ethernet.

 

 

Interface

 

interface

speed [10 100

￿ The 100Base-FX

 

configuration

 

fastEthernet 1/2

1000 auto]

module only

 

mode

 

Switch (config-if)#

 

supported for speed

 

 

 

 

speed 1000

 

 

100

 

 

 

 

 

 

 

￿ The 1000Base-FX

 

 

 

 

module only

 

 

 

 

supported for speed

 

 

 

 

1000 & auto

 

 

 

 

 

 

 

 

 

Use the flow control

 

 

 

 

configuration

 

 

 

 

command on Ethernet

 

Switch (config)#

flowcontrol on

Interface

ports to control traffic

 

interface

or no

configuration

rates during

On

fastEthernet 0/1

flowcontrol

mode

congestion.

 

Switch (config-if)#

 

 

Use the no form of this

 

flowcontrol on

 

 

command to disable

 

 

 

 

security on the port.

 

 

 

 

 

 

 

 

 

Use the security

 

 

 

 

configuration

 

Switch (config)#

security on or

Interface

command on Ethernet

 

interface

configuration

ports.

Disable

fastEthernet 0/1

no security

mode

Use the no form of this

 

Switch (config-if)#

 

 

 

 

command to disable

 

security on

 

 

security on the port.

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

 

 

22

 

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents User Guide FCC Warning CE Mark WarningContents WEB-BASED Management Hour Technical Support International Iii Appendix 100103 Features IntroductionManagement Software FeaturesSnmp MIB Vlan Igmp DhcpSntp SmtpPackage Contents Physical Dimension Front PanelLED Indicators PowerLED Status DescriptionPower Forwarding FDXLNK/ACT 25 Port /Giga port FDX/COL 25Rear Panel Desktop InstallationAttaching Rubber Pads Rack-mounted Installation Power OnNetwork Application Small WorkgroupSegment workgroup DC Power Input Connecting to the Switch Login in the Console InterfaceCommands Level Modes Access Prompt Exit Method About This ModeCLI Management User ExecExec Commands Set List System Commands SetDefault PasswordIp address MemeoryAccounting System-infoAddress VersionPort Commands Set Flowcontrol on FastEthernet 1/2Security on Priority on high State disableBandwidth Configuration Show interfaceStatus Show bandwidthTrunk Commands Set Vlan Commands Set V2 add V2 deleteV2 vlanid 2 port TagVlan Vlanidrange Vlan IDProtocol v2 add TaggedProtocol v2 delete Vlan protocolPvid Ingressfilter1 offSpanning-tree Spanning Tree Commands SetSpanning-tree on Priority number PriorityMax-age SecondsFastEthernet 0/2 Hello-timeStp-path-cost Forward-time Forward-timeStp-path-priority Stp-path-priorityQOS Commands Set Bridge-delay-bou Qos queuepolicyWrr hi 7 low FcfsIgmp Commands Set Igmp-query enableBound Igmp onMac / Filter Table Commands Set Ble static StaticFilter BleSnmp Commands Set Port Mirroring Commands Set 802.1x Commands Set Sharekey ServerportAccountport Nasid test1Supptimeout ServertimeoutTxperiod MaxrequestTftp Commands Set Flashconfig.textAccept CopyUPS Commands Set Tftpconfig.textFlash Tftp IPPoE Commands Set InfoTest10 Setpm onSystem log Commands Set Sntp Commands Set About Web-based Management System LoginPreparing for Web Management Port status Port Status interface Hour Technical Support International Port Statistics View the Port InformationAdministrator IP Address Switch SettingBasic Advanced Button to complete the configuration 801.1p Priority Misc ConfigurationCollisions Retry Forever Console Port Information Port Controls Aggregator setting TrunkingButton to add the port which is Aggregator Information Aggregator State Activity Forwarding and Filtering Igmp SnoopingStatic MAC Address MAC filtering Vlan configuration Port-based VlanTo create a new Vlan group VLAN-PortBase Add interface 802.1Q Vlan 802.1q Vlan interface Basic Will see the page as below Acceptable Frame type Spanning Tree System Configuration Per Port Configuration Button Port Mirroring Prot Mirroring interface Community strings Serve as password Snmp ManagementSecurity Manager Trap ManagerSntp Configuration 802.1X Configuration Misc ConfigPer port Configuration System Log To refresh the events log Tftp Update Firmware Save ConfigurationConfiguration Backup Tftp Restore ConfigurationTftp Backup Configuration Factory DefaultDefault IP address Default Gateway Subnet mask System Reboot Power StatusPoE Status PoE Status Interface MIL-SM2401MAF Incorrect connections Faulty or loose cablesNon-standard cables Diagnosing LED Indicators Diagnosing PoE problemsNo Power Forward Improper Network TopologiesPin Signal / Name MDI-XVCC- 1 1 VCC VCC- 2 2VCC VCC+ 3 3VCC+ VCC+ 6 6VCC+ Connector LED IndicatorsStandard RS-232 connector Switch architectureDimensions Remote powerVentilation SafetyEMI Console Port Pin Assignments PC DB9DB9 DTE DTE Pin #Cable Types and Specifications Max. Length Connector Cables100BASE-TX/10BASE-T Pin Assignments RJ-45 Pin Assignments Pin NumberPin MDI-X Signal Name MDI Signal Name Gigabit Copper/SFP mini-GBIC combo port
Related manuals
Manual 178 pages 19.96 Kb

MIL-SM2401MAF specifications

The Transition Networks MIL-SM2401MAF is a robust, military-grade Ethernet media converter designed to facilitate seamless communication within demanding environments. This media converter is specifically engineered to support the transmission of Ethernet data over long distances while ensuring reliability and performance in challenging conditions.

One of the standout features of the MIL-SM2401MAF is its dual-port configuration, which includes both a 10/100/1000Base-T port and a 1000Base-X SFP (Small Form-factor Pluggable) slot. This design allows users to connect various network devices, such as switches, routers, or servers, over copper or fiber connections. The flexibility of using an SFP slot ensures compatibility with different types of fiber media, catering to a broad range of networking needs.

The MIL-SM2401MAF supports extended ranges for data transmission, significantly surpassing the limitations of traditional Ethernet connections. With the ability to operate over multimode fiber up to 550 meters and single-mode fiber up to 10 kilometers, this device is ideal for long-haul communication within military applications and other critical infrastructure setups.

Another notable characteristic of the MIL-SM2401MAF is its compliance with military standards, ensuring durability and resilience in harsh environments. It is designed to withstand extreme temperatures, electromagnetic interference, and vibration, making it suitable for deployment in field operations or industrial settings. The device is also compliant with MIL-STD-810, which includes rigorous testing for environmental conditions.

In terms of power, the MIL-SM2401MAF offers flexible options, designed to accommodate various power sourcing needs. It can operate on a wide voltage range, enhancing its applicability in different situations while also including features for power redundancy.

Advanced features such as link fault pass-through, auto-negotiation, and automatic cable detection further enhance its reliability and ease of use. The simple plug-and-play operation means users can quickly integrate it into existing network infrastructure without needing extensive setup or configuration.

In summary, Transition Networks' MIL-SM2401MAF Ethernet media converter stands out as a versatile, high-performance solution suitable for military and industrial applications. Its combination of dual-port functionality, extended range capabilities, military-grade construction, and advanced operational features make it an invaluable tool for ensuring reliable communication in even the most challenging environments.
Top Page Image Contents