Transition Networks MIL-SM2401MAF manual QOS Commands Set

Page 41

Transition Networks

MIL-SM2401MAF

priority that is used when two switches tie for position as the root switch. Use the no form of this command to return to the default value.

￿QOS Commands Set

Commands

Command

Description

Defaults

Example

Level

 

 

 

 

 

 

 

 

 

qos

 

Enable/Disable

 

 

storm-control

Global

broadcast storm

 

Switch (config)#

[510152025

configuration

control. Use the no

OFF

qos storm-control

off (%)] or no

mode

form of this command

 

5

storm-control

 

to restore to default.

 

 

 

 

 

 

 

qos

 

 

 

 

low-priority-del

 

Enable/Disable low

 

Switch (config)#

ay-bound

Global

priority delay board.

 

 

qos

[onoff] [sec.]

configuration

Use the no form of

OFF

low-priority-delay

or no qos

mode

this command to

 

 

-bound on 1

low-priority-del

 

restore to default.

 

 

 

 

ay-bound

 

 

 

 

 

 

 

 

 

qos level

Global

 

0~3 LOW

Switch (config)#

configuration

[Priority] 0~7

[priority]

4~7 HI

qos level 2,3

mode

 

 

 

 

 

 

 

 

 

 

no qos level

Global

 

0~3 LOW

Switch (config)# no

configuration

[Priority] 0~7

[priority]

4~7 HI

qos level 0-7

mode

 

 

 

 

 

 

 

 

 

 

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

35

Page 40 Page 42
Image 41
Page 40 Page 42
Contents User Guide CE Mark Warning FCC WarningContents WEB-BASED Management Hour Technical Support International Iii 103 100Appendix Introduction FeaturesSnmp MIB Software FeaturesManagement Vlan Dhcp IgmpSmtp SntpPackage Contents Front Panel Physical DimensionPower LED IndicatorsLED Status DescriptionFDX Power ForwardingLNK/ACT 25 Port /Giga port FDX/COL 25Attaching Rubber Pads Desktop InstallationRear Panel Power On Rack-mounted InstallationSmall Workgroup Network ApplicationSegment workgroup DC Power Input Login in the Console Interface Connecting to the SwitchModes Access Prompt Exit Method About This Mode Commands LevelCLI Management User ExecExec System Commands Set Commands Set ListPassword DefaultIp address MemeorySystem-info AccountingAddress VersionPort Commands Set Security on FastEthernet 1/2Flowcontrol on Bandwidth State disablePriority on high Show interface ConfigurationStatus Show bandwidthTrunk Commands Set Vlan Commands Set V2 delete V2 addV2 vlanid 2 port TagVlan Vlan ID VlanidrangeProtocol v2 add TaggedVlan protocol Protocol v2 deletePvid Ingressfilter1 offSpanning-tree on Spanning Tree Commands SetSpanning-tree Priority Priority numberMax-age SecondsStp-path-cost Hello-timeFastEthernet 0/2 Forward-time Forward-timeStp-path-priority Stp-path-priorityQOS Commands Set Qos queuepolicy Bridge-delay-bouWrr hi 7 low FcfsIgmp-query enable Igmp Commands SetBound Igmp onMac / Filter Table Commands Set Static Ble staticFilter BleSnmp Commands Set Port Mirroring Commands Set 802.1x Commands Set Serverport SharekeyAccountport Nasid test1Servertimeout SupptimeoutTxperiod MaxrequestFlashconfig.text Tftp Commands SetAccept CopyTftpconfig.text UPS Commands SetFlash Tftp IPInfo PoE Commands SetTest10 Setpm onSystem log Commands Set Sntp Commands Set Preparing for Web Management System LoginAbout Web-based Management Port status Port Status interface Hour Technical Support International View the Port Information Port StatisticsAdministrator Basic Switch SettingIP Address Advanced Button to complete the configuration Collisions Retry Forever Misc Configuration801.1p Priority Console Port Information Port Controls Trunking Aggregator settingButton to add the port which is Aggregator Information Aggregator State Activity Igmp Snooping Forwarding and FilteringStatic MAC Address MAC filtering Port-based Vlan Vlan configurationTo create a new Vlan group VLAN-PortBase Add interface 802.1Q Vlan 802.1q Vlan interface Basic Will see the page as below Acceptable Frame type Spanning Tree System Configuration Per Port Configuration Button Port Mirroring Prot Mirroring interface Snmp Management Community strings Serve as passwordTrap Manager Security ManagerSntp Configuration Misc Config 802.1X ConfigurationPer port Configuration System Log To refresh the events log Save Configuration Tftp Update FirmwareTftp Restore Configuration Configuration BackupDefault IP address Default Gateway Subnet mask Factory DefaultTftp Backup Configuration Power Status System RebootPoE Status PoE Status Interface MIL-SM2401MAF Non-standard cables Faulty or loose cablesIncorrect connections Diagnosing PoE problems Diagnosing LED IndicatorsNo Power Forward Improper Network TopologiesMDI-X Pin Signal / NameVCC- 1 1 VCC VCC- 2 2VCC VCC+ 3 3VCC+ VCC+ 6 6VCC+ Standard LED IndicatorsConnector Switch architecture RS-232 connectorDimensions Remote powerEMI SafetyVentilation PC DB9 Console Port Pin AssignmentsDB9 DTE DTE Pin #Cables Cable Types and Specifications Max. Length Connector100BASE-TX/10BASE-T Pin Assignments RJ-45 Pin Assignments Pin NumberGigabit Copper/SFP mini-GBIC combo port Pin MDI-X Signal Name MDI Signal Name
Related manuals
Manual 178 pages 19.96 Kb

MIL-SM2401MAF specifications

The Transition Networks MIL-SM2401MAF is a robust, military-grade Ethernet media converter designed to facilitate seamless communication within demanding environments. This media converter is specifically engineered to support the transmission of Ethernet data over long distances while ensuring reliability and performance in challenging conditions.

One of the standout features of the MIL-SM2401MAF is its dual-port configuration, which includes both a 10/100/1000Base-T port and a 1000Base-X SFP (Small Form-factor Pluggable) slot. This design allows users to connect various network devices, such as switches, routers, or servers, over copper or fiber connections. The flexibility of using an SFP slot ensures compatibility with different types of fiber media, catering to a broad range of networking needs.

The MIL-SM2401MAF supports extended ranges for data transmission, significantly surpassing the limitations of traditional Ethernet connections. With the ability to operate over multimode fiber up to 550 meters and single-mode fiber up to 10 kilometers, this device is ideal for long-haul communication within military applications and other critical infrastructure setups.

Another notable characteristic of the MIL-SM2401MAF is its compliance with military standards, ensuring durability and resilience in harsh environments. It is designed to withstand extreme temperatures, electromagnetic interference, and vibration, making it suitable for deployment in field operations or industrial settings. The device is also compliant with MIL-STD-810, which includes rigorous testing for environmental conditions.

In terms of power, the MIL-SM2401MAF offers flexible options, designed to accommodate various power sourcing needs. It can operate on a wide voltage range, enhancing its applicability in different situations while also including features for power redundancy.

Advanced features such as link fault pass-through, auto-negotiation, and automatic cable detection further enhance its reliability and ease of use. The simple plug-and-play operation means users can quickly integrate it into existing network infrastructure without needing extensive setup or configuration.

In summary, Transition Networks' MIL-SM2401MAF Ethernet media converter stands out as a versatile, high-performance solution suitable for military and industrial applications. Its combination of dual-port functionality, extended range capabilities, military-grade construction, and advanced operational features make it an invaluable tool for ensuring reliable communication in even the most challenging environments.
Top Page Image Contents