Transition Networks CBFTF10XX-15X Installation, Set the Jumpers, Set the 4-Position Switch

CBFTF10xx-15x

INSTALLATION

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting the 4-position switch and the jumper(s) and when installing the Slide-in-Module. Failure to observe this caution could result in damage to, and subsequent failure of, the Media Converter.

INSTALLATION -- Continued

Set the Jumpers

The jumpers are located on the Media Converter circuit board. Use small needle-nosed pliers or a similar device to set the jumper.

Set the 4-Position Switch

The 4-position switch is located on the side of the Media Converter. Use a small flatblade screwdriver or a similar device to set the recessed switches. Refer to the drawing for the locations of the four individual switches.

Auto-Negotiation (UP=Enabled)

Copper Mode (UP=Full-Duplex)

Speed (UP=100Mb/s)

Fiber Mode (UP=Full-Duplex)

1 2 3 4

The Hardware/Software jumper is labeled “H” for hardware and “S” for

software (see the drawing below).H

S

Hardware	The Media Converter mode is determined by		Hardware Mode
	the 4-position switch settings listed above.
Software	The Media Converter mode is determined by	S		H
	the most-recently saved, on-board
			Software Mode
	microprocessor settings.

1. Auto-Negotiation

UP	Enables Auto-Negotiation on the copper port.
	Advertises 100 Mb/s full-duplex and half duplex,
	and 10 Mb/s full-duplex and half duplex.
DOWN	Disables Auto-Negotiation on the copper port.

2. Copper Mode

(Applies only if switch 1 is DOWN.)

UP	Forces full-duplex operation on the copper port.
DOWN	Forces half-duplex operation on the copper port.

3. Speed

(Applies only if switch 1 is DOWN.)

UP	Forces 100 Mb/s operation on the copper port.
DOWN	Forces 10 Mb/s operation on the copper port.
4. Fiber Mode
UP	Forces full-duplex operation on the fiber port.
DOWN	Forces half-duplex operation on the fiber port.

The Far-End Fault jumper is labeled “FE” for enable Far-End Fault and “FD”

for disable Far-End Fault (see the drawing below).

FEFD

Enable	A fault on the fiber link causes the Media	Enable Far-End Fault
	Converter to transmit a Far-End Fault signal.
Disable	No Far-End Fault signal is transmitted when a	FE	FD
	fault occurs.

Disable Far-End Fault

Installing the Slide-In-Module

CAUTION: Slots in the PointSystem™ Chassis without a Slide-in-Module installed MUST have a protective plate covering the empty slot for Class A and/or Class B compliance.

To install the CGETF10xx-15x Media Converter Slide-in-Module:

1.Locate an empty installation slot on the PointSystem™ Chassis.

2.Carefully slide the Slide-in-Module into the installation slot, aligning the Slide-in-Module with the installation guides.

3.Ensure that the Slide-in-Module is firmly seated against the back of the chassis.

4.Secure the Slide-in-Module by securing the panel fastener screw (attached to the Slide-in-Module) to the chassis front.

TX PWR

PWR

PWR

PWR

PWR

LA

LKS

PWR

LKS

LA

LKS

SPD

PWR

LNK

LNK

RXF

LKM

FLNK

LKM

RXF

LKM

FRX

FLNK

RX

LNK

RXC

COL

CLNK

RXC

COL

TX

CRX

CLNK

R

Link Alert

TX

TX

Link Alert

E

E

S

E

D

RXSinglemode

RXSinglemode

D

RXSinglemode

TX

E

100BASE-FX

I 0

I 0

T

10BASE-T

10BASE-T

INIT

10/100SX

10BASE-

TERM

TX

TX

FL

TX

RX

SERIAL

0

50½

Multimode

Multimode

0

50½

Multimode

100BASE-TX

10BASE-2

10BASE-

RX

RX

RX

2

CPSMM120

CECF100

CFETF110

CFMFF100

CETCF100

CFMFF100

CFETF100

Panel Fastener Screw

2 Tech Support: 800-260-1312International: 952-941-76007am-6pm CST (GMT-6:00) techsupport@transition.com -- Select the “Transition Now” Link for a Live Web Chat 3