Transition Networks SISGM1040-244 user manual System Information, IP Configuration

Page 65

Transition Networks

SISGM1040-244

System Information

Assigning the system name, location and view the system information

￿System Name: Assign the name of switch. The maximum length is 64 bytes

￿System Description: Displays the description of switch. Read only cannot be modified

￿System Location: Assign the switch physical location. The maximum length is 64 bytes

￿System Contact: Enter the name of contact person or organization

￿Firmware Version: Displays the switch’s firmware version

￿Kernel Version: Displays the kernel software version

￿MAC Address: Displays the unique hardware address assigned by manufacturer (default)

System information interface

IP Configuration

User can configure the IP Settings and DHCP client function

￿DHCP Client: To enable or disable the DHCP client function. When DHCP client function is enabling, the industrial switch will be assigned the IP address from the network DHCP server. The default IP address will be replace by the DHCP server

assigned IP address. After user click ‘Apply’ button, a popup dialog show up. It is to

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

Page 64 Page 66
Image 65
Page 64 Page 66
Contents SISGM1040-244 Content Hardware Installation Web-Based Management System Event Log Syslog Configuration 101 110 SFP Advantage IntroductionSFP with DMI Digital Monitoring Interface function Dual Power InputHigh-Speed Transmissions Flexible MountingEasy Troubleshooting Wide Operating TemperatureGvrp FeaturesTransition Networks SISGM1040-244 Technical Specification Power Consumption DiagnosticsPower Input Fault OutputVibration Free FallShock Packing List Safety PrecautionFront Panel Hardware DescriptionTop View Wiring the Power InputsLED LED IndicatorsRJ-45 Pin Assignments Pin Number PortsCabling Pin MDI-X Signal Name MDI Signal NameTransceiver to the SFP module Transceiver Inserted LC connector to the transceiver Remove LC connector Pull out from the SFP module DIN-Rail Mounting Mounting InstallationWall Mount Plate Mounting Transition Networks SISGM1040-244 Installation Steps Hardware InstallationCoupling Ring Application Ring ApplicationDual Homing Application Console Management Connecting to the Console PortPin Assignment Login in the Console InterfaceDB9 Connector RJ-45 Connector Hour Technical Support International CLI Management Modes Access Prompt Exit About This Mode1 Method Commands LevelSystem Name Commands Set List System Commands SetSystem Location PasswordSystem Description System ContactIP address Subnet maskHours Portid Port Commands SetFull half 101001000autoValue Enable Disable Trunk Commands Set No aggregator lacp Show aggregatorGroupID No aggregator groupVlan Commands Set DMI Commands SetGroup Name PortNumbersTaggedVID List PortNumberUntaggedVID Seconds Spanning Tree Commands Set~61440 Hello-time seconds Spanning-treeForward-time seconds Stp-path-costTrueFalse AutoTrueFalseIgmp Commands Set QOS Commands SetMac / Filter Table Commands Set Snmp Commands Set NoAuthNoPrivAuthNoP RivAuthPriv NameExactPrifix Read View Name Write View Name Notify ViewRemove specified Switchconfig#no snmpv3 Port Mirroring Commands SetIv match-rule Exact views V1 RXTXBothPort ID 802.1x Commands SetNumber WordsSec Authorize Tftp Commands SetDisable reject accept Clientserverboth SystemLog, Smtp and Event Commands SetAccount Index Email addressLink-UPLink-DownBot SystemlogSMTPBothStart time End time Sntp Commands SetMinute Timezone1st Ring Port 2nd Ring Ring Commands SetCoupling Port Control PortPreparing for Web Management About Web-based ManagementSystem Login Main interface System Information IP ConfigurationDhcp Server System configuration Dhcp Client System Configuration Dhcp Server Port and IP Bindings Tftp Update FirmwareTftp Backup Configuration Tftp Restore ConfigurationBackup File Name fill the file name System Event Log Syslog ConfigurationSystem Event Log Smtp Configuration Server IP Address column System Event Log Event Configuration Hour Technical Support International Local Time Zone Conversion from UTC Time at 1200 UTC Fault Relay AlarmSntp Configuration Transition NetworksSISGM1040-244 Switch Timer Displays the switch current time Click Daylight Saving Offset mins set up the offset timeIP Security New configuration will lose when switch power offUser Authentication Port Statistics Button to clean all countsPort Control Port Trunk Aggregator settingAggregator Information Active status will be created automatically State ActivityPort Mirroring Rate Limiting DMI Digital Monitoring Interface Vlan configuration Vlan configuration Port-based Vlan Transition Networks SISGM1040-244 Vlan Port Based interface New configuration will lose when switch power off 802.1Q Vlan Hybrid Link Both Access Link and Trunk Link are available 802.1Q ConfigurationGroup Configuration Rapid Spanning Tree Rstp System ConfigurationDelay Time Rstp Port Configuration Snmp Configuration Community Strings System ConfigurationTrap Configuration User Profile SNMPV3 ConfigurationContext Table Page MIBview Table Access TableGroup Table QoS Policy and Priority Type QoS ConfigurationPort Base Priority TOS Configuration Igmp ConfigurationCOS Configuration Query Message DescriptionReport LeaveRing Ring and Rstp function cannot exist at the same time Security 802.1x Per Port Configuration Misc Configuration Add the Static MAC Address MAC Address TableMAC Filtering All MAC Addresses System Reboot Factory DefaultSave Configuration Troubles shooting

SISGM1040-244 specifications

Transition Networks SISGM1040-244 is a high-performance Ethernet switch designed to meet the needs of small to medium-sized businesses and industrial applications. This managed switch offers robust features and advanced technologies that ensure reliable connectivity and flexibility in various network environments.

One of the standout features of the SISGM1040-244 is its support for Gigabit Ethernet, allowing for data transfer rates of up to 1000 Mbps. This enables efficient handling of bandwidth-intensive applications, making it a suitable choice for data centers, surveillance systems, and high-definition video streaming. The switch includes multiple ports, giving users the ability to connect multiple devices, enhancing network scalability and performance.

The SISGM1040-244 is equipped with Layer 2 management capabilities, offering users control over their network traffic and allowing for easy configuration and monitoring. Its user-friendly interface simplifies the management process, enabling IT administrators to implement VLANs, network segmentation, and Quality of Service (QoS) features effectively. These functionalities help optimize network performance by prioritizing critical traffic and ensuring a smooth user experience.

Another notable aspect of the SISGM1040-244 is its adherence to IEEE standards, including IEEE 802.3, 802.3u, and 802.3ab, ensuring compatibility with a wide range of devices and facilitating seamless integration into existing networks. Additionally, the switch includes support for advanced security features like port security, MAC address filtering, and access control lists, which help protect the network from unauthorized access and attacks.

The design of the SISGM1040-244 is also noteworthy, featuring a rugged build that allows for deployment in harsh environments. Its fanless operation not only contributes to a quieter workspace but also increases its reliability by reducing potential failure points associated with moving parts. This makes it an ideal choice for industrial settings, where dust and temperature fluctuations are common.

In summary, Transition Networks SISGM1040-244 is a feature-rich managed Gigabit Ethernet switch that caters to the demands of modern networking. With advanced management capabilities, robust security features, and a durable design, it is a reliable choice for businesses looking to enhance their network performance while ensuring scalability and security. Its combination of flexibility and performance positions it as a valuable component in both enterprise and industrial applications, making it a smart investment for network expansion and improvement.
Top Page Image Contents