Transition Networks SISGM1040-244 user manual Server IP Address column

Page 72

Transition Networks

SISGM1040-244

3.

Sender: key in a complete email address, e.g. switch102@123.com, to identify

 

where the event log comes from.

4.

Authentication: mark the check box to enable and configure the email account and

 

password for authentication (when Email Alert enabled, this function will then be

 

available).

5.

Mail Account: set up the email account, e.g. johnadmin, to receive the alert. It must

 

be an existing email account on the mail server, which you had set up in SMTP

 

Server IP Address column.

6.

Password: The email account password.

7.

Confirm Password: reconfirm the password.

8.

Rcpt e-mail Address 1 ~ 6: you can assign up to 6 e-mail accounts also to receive

 

the alert.

9.

Click Apply .

SMTP Configuration interface

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

Page 71 Page 73
Image 72
Page 71 Page 73
Contents SISGM1040-244 Content Hardware Installation Web-Based Management System Event Log Syslog Configuration 101 110 Introduction SFP AdvantageDual Power Input SFP with DMI Digital Monitoring Interface functionHigh-Speed Transmissions Flexible MountingWide Operating Temperature Easy TroubleshootingFeatures GvrpTransition Networks SISGM1040-244 Technical Specification Diagnostics Power ConsumptionPower Input Fault OutputFree Fall ShockVibration Safety Precaution Packing ListHardware Description Front PanelWiring the Power Inputs Top ViewLED Indicators LEDPorts RJ-45 Pin Assignments Pin NumberPin MDI-X Signal Name MDI Signal Name CablingTransceiver to the SFP module Transceiver Inserted LC connector to the transceiver Remove LC connector Pull out from the SFP module Mounting Installation DIN-Rail MountingWall Mount Plate Mounting Transition Networks SISGM1040-244 Hardware Installation Installation StepsRing Application Coupling Ring ApplicationDual Homing Application Connecting to the Console Port Console ManagementLogin in the Console Interface DB9 Connector RJ-45 ConnectorPin Assignment Hour Technical Support International CLI Management Commands Level Modes Access Prompt Exit About This Mode1 MethodCommands Set List System Commands Set System NamePassword System LocationSystem Description System ContactSubnet mask HoursIP address Port Commands Set PortidFull half 101001000autoValue Enable Disable Trunk Commands Set Show aggregator No aggregator lacpGroupID No aggregator groupDMI Commands Set Vlan Commands SetGroup Name PortNumbersPortNumber UntaggedVIDTaggedVID List Spanning Tree Commands Set ~61440Seconds Spanning-tree Hello-time secondsForward-time seconds Stp-path-costAutoTrueFalse TrueFalseQOS Commands Set Igmp Commands SetMac / Filter Table Commands Set Snmp Commands Set Name NoAuthNoPrivAuthNoP RivAuthPrivExactPrifix Read View Name Write View Name Notify ViewPort Mirroring Commands Set Remove specified Switchconfig#no snmpv3Iv match-rule Exact views V1 RXTXBoth802.1x Commands Set Port IDWords SecNumber Tftp Commands Set Disable reject acceptAuthorize SystemLog, Smtp and Event Commands Set ClientserverbothAccount Index Email addressSystemlogSMTPBoth Link-UPLink-DownBotSntp Commands Set Start time End timeMinute TimezoneRing Commands Set 1st Ring Port 2nd RingCoupling Port Control PortAbout Web-based Management Preparing for Web ManagementSystem Login Main interface IP Configuration System InformationDhcp Server System configuration Dhcp Client System Configuration Tftp Update Firmware Dhcp Server Port and IP BindingsTftp Restore Configuration Tftp Backup ConfigurationSystem Event Log Syslog Configuration Backup File Name fill the file nameSystem Event Log Smtp Configuration Server IP Address column System Event Log Event Configuration Hour Technical Support International Fault Relay Alarm Sntp ConfigurationLocal Time Zone Conversion from UTC Time at 1200 UTC Transition NetworksSISGM1040-244 Daylight Saving Offset mins set up the offset time Switch Timer Displays the switch current time ClickNew configuration will lose when switch power off IP SecurityUser Authentication Button to clean all counts Port StatisticsPort Control Aggregator setting Port TrunkAggregator Information State Activity Active status will be created automaticallyPort Mirroring Rate Limiting DMI Digital Monitoring Interface Vlan configuration Vlan configuration Port-based Vlan Transition Networks SISGM1040-244 Vlan Port Based interface New configuration will lose when switch power off 802.1Q Vlan 802.1Q Configuration Hybrid Link Both Access Link and Trunk Link are availableGroup Configuration Rstp System Configuration Rapid Spanning TreeDelay Time Rstp Port Configuration Snmp Configuration System Configuration Community StringsTrap Configuration SNMPV3 Configuration Context TableUser Profile Page Access Table Group TableMIBview Table QoS Configuration QoS Policy and Priority TypePort Base Priority Igmp Configuration COS ConfigurationTOS Configuration Message Description QueryReport LeaveRing Ring and Rstp function cannot exist at the same time Security 802.1x Per Port Configuration Misc Configuration MAC Address Table Add the Static MAC AddressMAC Filtering All MAC Addresses Factory Default Save ConfigurationSystem Reboot Troubles shooting

SISGM1040-244 specifications

Transition Networks SISGM1040-244 is a high-performance Ethernet switch designed to meet the needs of small to medium-sized businesses and industrial applications. This managed switch offers robust features and advanced technologies that ensure reliable connectivity and flexibility in various network environments.

One of the standout features of the SISGM1040-244 is its support for Gigabit Ethernet, allowing for data transfer rates of up to 1000 Mbps. This enables efficient handling of bandwidth-intensive applications, making it a suitable choice for data centers, surveillance systems, and high-definition video streaming. The switch includes multiple ports, giving users the ability to connect multiple devices, enhancing network scalability and performance.

The SISGM1040-244 is equipped with Layer 2 management capabilities, offering users control over their network traffic and allowing for easy configuration and monitoring. Its user-friendly interface simplifies the management process, enabling IT administrators to implement VLANs, network segmentation, and Quality of Service (QoS) features effectively. These functionalities help optimize network performance by prioritizing critical traffic and ensuring a smooth user experience.

Another notable aspect of the SISGM1040-244 is its adherence to IEEE standards, including IEEE 802.3, 802.3u, and 802.3ab, ensuring compatibility with a wide range of devices and facilitating seamless integration into existing networks. Additionally, the switch includes support for advanced security features like port security, MAC address filtering, and access control lists, which help protect the network from unauthorized access and attacks.

The design of the SISGM1040-244 is also noteworthy, featuring a rugged build that allows for deployment in harsh environments. Its fanless operation not only contributes to a quieter workspace but also increases its reliability by reducing potential failure points associated with moving parts. This makes it an ideal choice for industrial settings, where dust and temperature fluctuations are common.

In summary, Transition Networks SISGM1040-244 is a feature-rich managed Gigabit Ethernet switch that caters to the demands of modern networking. With advanced management capabilities, robust security features, and a durable design, it is a reliable choice for businesses looking to enhance their network performance while ensuring scalability and security. Its combination of flexibility and performance positions it as a valuable component in both enterprise and industrial applications, making it a smart investment for network expansion and improvement.
Top Page Image Contents