Transition Networks SISGM1040-244 user manual Dhcp Server System configuration

Page 66

Transition Networks

SISGM1040-244

inform the user that when the DHCP client is enabling, the current IP will lose and user should find the new IP on the DHCP server.

￿IP Address: Assign the IP address that the network is using. If DHCP client function is enabling, and then user don’t need to assign the IP address. And, the network DHCP server will assign the IP address for the industrial switch and displays in this column. The default IP is 192.168.1.77.

￿Subnet Mask: Assign the subnet mask of the IP address. If DHCP client function is enabling, and then user do not need to assign the subnet mask.

￿Gateway: Assign the network gateway for the industrial switch. The default gateway is 192.168.1.254.

￿DNS1: Assign the primary DNS IP address.

￿DNS2: Assign the secondary DNS IP address.

￿And then, click

Apply

IP configuration interface

DHCP Server – System configuration

The system provides the DHCP server function. Enable the DHCP server function, the switch system will be a DHCP server.

￿DHCP Server: Enable or Disable the DHCP Server function. Enable – the switch will be the DHCP server on your local network.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

Page 65 Page 67
Image 66
Page 65 Page 67
Contents SISGM1040-244 Content Hardware Installation Web-Based Management System Event Log Syslog Configuration 101 110 Introduction SFP AdvantageHigh-Speed Transmissions Dual Power InputSFP with DMI Digital Monitoring Interface function Flexible MountingWide Operating Temperature Easy TroubleshootingFeatures GvrpTransition Networks SISGM1040-244 Technical Specification Power Input DiagnosticsPower Consumption Fault OutputFree Fall ShockVibration Safety Precaution Packing ListHardware Description Front PanelWiring the Power Inputs Top ViewLED Indicators LEDPorts RJ-45 Pin Assignments Pin NumberPin MDI-X Signal Name MDI Signal Name CablingTransceiver to the SFP module Transceiver Inserted LC connector to the transceiver Remove LC connector Pull out from the SFP module Mounting Installation DIN-Rail MountingWall Mount Plate Mounting Transition Networks SISGM1040-244 Hardware Installation Installation StepsRing Application Coupling Ring ApplicationDual Homing Application Connecting to the Console Port Console ManagementLogin in the Console Interface DB9 Connector RJ-45 ConnectorPin Assignment Hour Technical Support International CLI Management Commands Level Modes Access Prompt Exit About This Mode1 MethodCommands Set List System Commands Set System NameSystem Description PasswordSystem Location System ContactSubnet mask HoursIP address Full half Port Commands SetPortid 101001000autoValue Enable Disable Trunk Commands Set GroupID Show aggregatorNo aggregator lacp No aggregator groupGroup Name DMI Commands SetVlan Commands Set PortNumbersPortNumber UntaggedVIDTaggedVID List Spanning Tree Commands Set ~61440Seconds Forward-time seconds Spanning-treeHello-time seconds Stp-path-costAutoTrueFalse TrueFalseQOS Commands Set Igmp Commands SetMac / Filter Table Commands Set Snmp Commands Set ExactPrifix NameNoAuthNoPrivAuthNoP RivAuthPriv Read View Name Write View Name Notify ViewIv match-rule Exact views V1 Port Mirroring Commands SetRemove specified Switchconfig#no snmpv3 RXTXBoth802.1x Commands Set Port IDWords SecNumber Tftp Commands Set Disable reject acceptAuthorize Account SystemLog, Smtp and Event Commands SetClientserverboth Index Email addressSystemlogSMTPBoth Link-UPLink-DownBotMinute Sntp Commands SetStart time End time TimezoneCoupling Port Ring Commands Set1st Ring Port 2nd Ring Control PortAbout Web-based Management Preparing for Web ManagementSystem Login Main interface IP Configuration System InformationDhcp Server System configuration Dhcp Client System Configuration Tftp Update Firmware Dhcp Server Port and IP BindingsTftp Restore Configuration Tftp Backup ConfigurationSystem Event Log Syslog Configuration Backup File Name fill the file nameSystem Event Log Smtp Configuration Server IP Address column System Event Log Event Configuration Hour Technical Support International Fault Relay Alarm Sntp ConfigurationLocal Time Zone Conversion from UTC Time at 1200 UTC Transition NetworksSISGM1040-244 Daylight Saving Offset mins set up the offset time Switch Timer Displays the switch current time ClickNew configuration will lose when switch power off IP SecurityUser Authentication Button to clean all counts Port StatisticsPort Control Aggregator setting Port TrunkAggregator Information State Activity Active status will be created automaticallyPort Mirroring Rate Limiting DMI Digital Monitoring Interface Vlan configuration Vlan configuration Port-based Vlan Transition Networks SISGM1040-244 Vlan Port Based interface New configuration will lose when switch power off 802.1Q Vlan 802.1Q Configuration Hybrid Link Both Access Link and Trunk Link are availableGroup Configuration Rstp System Configuration Rapid Spanning TreeDelay Time Rstp Port Configuration Snmp Configuration System Configuration Community StringsTrap Configuration SNMPV3 Configuration Context TableUser Profile Page Access Table Group TableMIBview Table QoS Configuration QoS Policy and Priority TypePort Base Priority Igmp Configuration COS ConfigurationTOS Configuration Report Message DescriptionQuery LeaveRing Ring and Rstp function cannot exist at the same time Security 802.1x Per Port Configuration Misc Configuration MAC Address Table Add the Static MAC AddressMAC Filtering All MAC Addresses Factory Default Save ConfigurationSystem Reboot Troubles shooting

SISGM1040-244 specifications

Transition Networks SISGM1040-244 is a high-performance Ethernet switch designed to meet the needs of small to medium-sized businesses and industrial applications. This managed switch offers robust features and advanced technologies that ensure reliable connectivity and flexibility in various network environments.

One of the standout features of the SISGM1040-244 is its support for Gigabit Ethernet, allowing for data transfer rates of up to 1000 Mbps. This enables efficient handling of bandwidth-intensive applications, making it a suitable choice for data centers, surveillance systems, and high-definition video streaming. The switch includes multiple ports, giving users the ability to connect multiple devices, enhancing network scalability and performance.

The SISGM1040-244 is equipped with Layer 2 management capabilities, offering users control over their network traffic and allowing for easy configuration and monitoring. Its user-friendly interface simplifies the management process, enabling IT administrators to implement VLANs, network segmentation, and Quality of Service (QoS) features effectively. These functionalities help optimize network performance by prioritizing critical traffic and ensuring a smooth user experience.

Another notable aspect of the SISGM1040-244 is its adherence to IEEE standards, including IEEE 802.3, 802.3u, and 802.3ab, ensuring compatibility with a wide range of devices and facilitating seamless integration into existing networks. Additionally, the switch includes support for advanced security features like port security, MAC address filtering, and access control lists, which help protect the network from unauthorized access and attacks.

The design of the SISGM1040-244 is also noteworthy, featuring a rugged build that allows for deployment in harsh environments. Its fanless operation not only contributes to a quieter workspace but also increases its reliability by reducing potential failure points associated with moving parts. This makes it an ideal choice for industrial settings, where dust and temperature fluctuations are common.

In summary, Transition Networks SISGM1040-244 is a feature-rich managed Gigabit Ethernet switch that caters to the demands of modern networking. With advanced management capabilities, robust security features, and a durable design, it is a reliable choice for businesses looking to enhance their network performance while ensuring scalability and security. Its combination of flexibility and performance positions it as a valuable component in both enterprise and industrial applications, making it a smart investment for network expansion and improvement.
Top Page Image Contents