Transition Networks SISGM1040-244 user manual Port Control

Page 81

Transition Networks

SISGM1040-244

Port Statistics interface

Port Control

In Port control, you can view every port status that depended on user setting and the negotiation result.

1.Port: select the port that you want to configure.

2.State: Current port status. The port can be set to disable or enable mode. If the port setting is disable then will not receive or transmit any packet.

3.Negotiation: set auto negotiation status of port.

4.Speed: set the port link speed.

5.Duplex: set full-duplex or half-duplex mode of the port.

6.Flow Control: set flow control function is Symmetric or Asymmetric in Full Duplex mode. The default value is Symmetric.

7.Security: When its state is ‘On’, means this port accepts only one MAC address.

8.Click

Apply .

Port Control interface

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

Page 80 Page 82
Image 81
Page 80 Page 82
Contents SISGM1040-244 Content Hardware Installation Web-Based Management System Event Log Syslog Configuration 101 110 SFP Advantage IntroductionSFP with DMI Digital Monitoring Interface function Dual Power InputHigh-Speed Transmissions Flexible MountingEasy Troubleshooting Wide Operating TemperatureGvrp FeaturesTransition Networks SISGM1040-244 Technical Specification Power Consumption DiagnosticsPower Input Fault OutputFree Fall ShockVibration Packing List Safety PrecautionFront Panel Hardware DescriptionTop View Wiring the Power InputsLED LED IndicatorsRJ-45 Pin Assignments Pin Number PortsCabling Pin MDI-X Signal Name MDI Signal NameTransceiver to the SFP module Transceiver Inserted LC connector to the transceiver Remove LC connector Pull out from the SFP module DIN-Rail Mounting Mounting InstallationWall Mount Plate Mounting Transition Networks SISGM1040-244 Installation Steps Hardware InstallationCoupling Ring Application Ring ApplicationDual Homing Application Console Management Connecting to the Console PortLogin in the Console Interface DB9 Connector RJ-45 ConnectorPin Assignment Hour Technical Support International CLI Management Modes Access Prompt Exit About This Mode1 Method Commands LevelSystem Name Commands Set List System Commands SetSystem Location PasswordSystem Description System ContactSubnet mask HoursIP address Portid Port Commands SetFull half 101001000autoValue Enable Disable Trunk Commands Set No aggregator lacp Show aggregatorGroupID No aggregator groupVlan Commands Set DMI Commands SetGroup Name PortNumbersPortNumber UntaggedVIDTaggedVID List Spanning Tree Commands Set ~61440Seconds Hello-time seconds Spanning-treeForward-time seconds Stp-path-costTrueFalse AutoTrueFalseIgmp Commands Set QOS Commands SetMac / Filter Table Commands Set Snmp Commands Set NoAuthNoPrivAuthNoP RivAuthPriv NameExactPrifix Read View Name Write View Name Notify ViewRemove specified Switchconfig#no snmpv3 Port Mirroring Commands SetIv match-rule Exact views V1 RXTXBothPort ID 802.1x Commands SetWords SecNumber Tftp Commands Set Disable reject acceptAuthorize Clientserverboth SystemLog, Smtp and Event Commands SetAccount Index Email addressLink-UPLink-DownBot SystemlogSMTPBothStart time End time Sntp Commands SetMinute Timezone1st Ring Port 2nd Ring Ring Commands SetCoupling Port Control PortPreparing for Web Management About Web-based ManagementSystem Login Main interface System Information IP ConfigurationDhcp Server System configuration Dhcp Client System Configuration Dhcp Server Port and IP Bindings Tftp Update FirmwareTftp Backup Configuration Tftp Restore ConfigurationBackup File Name fill the file name System Event Log Syslog ConfigurationSystem Event Log Smtp Configuration Server IP Address column System Event Log Event Configuration Hour Technical Support International Fault Relay Alarm Sntp ConfigurationLocal Time Zone Conversion from UTC Time at 1200 UTC Transition NetworksSISGM1040-244 Switch Timer Displays the switch current time Click Daylight Saving Offset mins set up the offset timeIP Security New configuration will lose when switch power offUser Authentication Port Statistics Button to clean all countsPort Control Port Trunk Aggregator settingAggregator Information Active status will be created automatically State ActivityPort Mirroring Rate Limiting DMI Digital Monitoring Interface Vlan configuration Vlan configuration Port-based Vlan Transition Networks SISGM1040-244 Vlan Port Based interface New configuration will lose when switch power off 802.1Q Vlan Hybrid Link Both Access Link and Trunk Link are available 802.1Q ConfigurationGroup Configuration Rapid Spanning Tree Rstp System ConfigurationDelay Time Rstp Port Configuration Snmp Configuration Community Strings System ConfigurationTrap Configuration SNMPV3 Configuration Context TableUser Profile Page Access Table Group TableMIBview Table QoS Policy and Priority Type QoS ConfigurationPort Base Priority Igmp Configuration COS ConfigurationTOS Configuration Query Message DescriptionReport LeaveRing Ring and Rstp function cannot exist at the same time Security 802.1x Per Port Configuration Misc Configuration Add the Static MAC Address MAC Address TableMAC Filtering All MAC Addresses Factory Default Save ConfigurationSystem Reboot Troubles shooting

SISGM1040-244 specifications

Transition Networks SISGM1040-244 is a high-performance Ethernet switch designed to meet the needs of small to medium-sized businesses and industrial applications. This managed switch offers robust features and advanced technologies that ensure reliable connectivity and flexibility in various network environments.

One of the standout features of the SISGM1040-244 is its support for Gigabit Ethernet, allowing for data transfer rates of up to 1000 Mbps. This enables efficient handling of bandwidth-intensive applications, making it a suitable choice for data centers, surveillance systems, and high-definition video streaming. The switch includes multiple ports, giving users the ability to connect multiple devices, enhancing network scalability and performance.

The SISGM1040-244 is equipped with Layer 2 management capabilities, offering users control over their network traffic and allowing for easy configuration and monitoring. Its user-friendly interface simplifies the management process, enabling IT administrators to implement VLANs, network segmentation, and Quality of Service (QoS) features effectively. These functionalities help optimize network performance by prioritizing critical traffic and ensuring a smooth user experience.

Another notable aspect of the SISGM1040-244 is its adherence to IEEE standards, including IEEE 802.3, 802.3u, and 802.3ab, ensuring compatibility with a wide range of devices and facilitating seamless integration into existing networks. Additionally, the switch includes support for advanced security features like port security, MAC address filtering, and access control lists, which help protect the network from unauthorized access and attacks.

The design of the SISGM1040-244 is also noteworthy, featuring a rugged build that allows for deployment in harsh environments. Its fanless operation not only contributes to a quieter workspace but also increases its reliability by reducing potential failure points associated with moving parts. This makes it an ideal choice for industrial settings, where dust and temperature fluctuations are common.

In summary, Transition Networks SISGM1040-244 is a feature-rich managed Gigabit Ethernet switch that caters to the demands of modern networking. With advanced management capabilities, robust security features, and a durable design, it is a reliable choice for businesses looking to enhance their network performance while ensuring scalability and security. Its combination of flexibility and performance positions it as a valuable component in both enterprise and industrial applications, making it a smart investment for network expansion and improvement.
Top Page Image Contents