Transition Networks CSEFE10XX-10X specifications Cable Specifications, Copper Cable, Fiber Cable

CSEFE10xx-10x

Operation -- Continued

SNMP

Cable Specifications

The physical characteristics must meet or exceed IEEE 802.3™ specifications.

Use SNMP at an attached terminal or at a remote location to monitor the media converter by monitoring:

•Media converter power

•Copper link status

•Fiber link status

•Copper receive status

•Fiber receive status

•Link Pass-Through status

•Media converter speed

Also, use SNMP to enter network commands that:

•Enable/disable Link Pass-Through

•Set the speed to 100 Mb/s or 10 Mb/s

•Power down the media converter

See the on-line documentation that comes with Transition Networks FocalPoint™ software for applicable commands and usage.

Cable Specifications

Copper Cable

Category 3: (Minimum requirement for 10 Mb/s operation)

Gauge	24 to 22 AWG
Attenuation	11.5 dB/100m @ 5-10 MHz
Category 5: (Minimum requirement for 100 Mb/s operation)
Gauge	24 to 22 AWG
Attenuation	22.0 dB /100m @ 100 MHz

• Straight-through or crossover copper cable may be used.

• Shielded (STP) or unshielded (UTP) twisted-pair cable may be used.

• Pins 1&2 and 3&6 are the two active pairs in an Ethernet network .

Fiber Cable

Bit Error Rate:

Single mode:

CSEFE1012-100

Fiber-optic Transmitter Power:

Fiber-optic Receiver Sensitivity:

Link Budget:

CSEFE1014-100

Fiber-optic Transmitter Power:

Fiber-optic Receiver Sensitivity:

Link Budget:

CSEFE1015-100

Fiber Optic Transmitter Power:

Fiber Optic Receiver Sensitivity:

Link Budget:

CSEFE1022-100

Fiber Optic Transmitter Power:

Fiber Optic Receiver Sensitivity:

Link Budget:

CSEFE1029-100

Fiber-optic Transmitter Power:

Fiber-optic Receiver Sensitivity:

Link Budget:

CSEFE1029-101

Fiber-optic Transmitter Power:

Fiber-optic Receiver Sensitivity:

Link Budget:

<10-99 µm

1310 nm single mode

min: -15.0 dBm	max: -8.0 dBm
min: -32.0 dBm	max: -5.0 dBm
17.0 dB
1310 nm single mode
min: -15.0 dBm	max: -8.0 dBm
min: -32.0 dBm	max: -5.0 dBm
17.0 dB
1310 nm single mode
min: -8.0 dBm	max: -2.0 dBm
min: -34.0 dBm	max: -5.0 dBm
26.0 dB
1310 nm single mode
min: -8.0 dBm	max: -2.0 dBm
min: -34.0 dBm	max: -5.0 dBm
26.0 dB

1310 nm (TX)/1550 nm (RX) simplex

min: -14.0 dBm	max: -8.0 dBm
min: -33.0 dBm	max: -3.0 dBm
19.0 dB

1550 nm (TX)/1310 nm (RX) simplex

min: -14.0 dBm	max: -8.0 dBm
min: -33.0 dBm	max: -3.0 dBm
19.0 dB

• RJ-45 Pin-out: Pin 1 = TD+, Pin 2 = TD-, Pin 3 = RD+, Pin 6 = RD-

• Use only dedicated wire pairs for the active pins:

(e.g., blue/white & white/blue, orange/white & white/orange, etc.)

• Do not use flat or silver satin wire.

	Straight-Through Cable				Crossover Cable
Twisted Pair #1		1	1	Twisted Pair #1	1	1
		2	2		2	2
Twisted Pair #2		3	3	Twisted Pair #2	3	3
		6	6		6	6

The fiber optic transmitters on this device meet Class I Laser safety requirements per IEC-825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.

6 24-Hour Technical Support: 1-800-260-1312-- International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat 7