Fujitsu BX600 Snmp-server host ipaddr name no snmp-server host name, Snmp-server enable traps

Page 193

Management Commands

Command Reference

Command Mode

Global Config

7.5.4.7snmp-server host

This command sets a client IP address for an SNMP community. The address is the associated community SNMP packet sending address and is used along with the client IP mask value to denote a range of IP addresses from which SNMP clients may use that community to access the device. A value of 0.0.0.0 allows access from any IP address. Otherwise, this value is ANDed with the mask to determine the range of allowed client IP addresses. The name is the applicable community name.

Syntax

snmp-server host <ipaddr> <name> no snmp-server host <name>

<name> - community name. <ipaddr> - a client IP address.

no - This command sets a client IP address for an SNMP community to 0.0.0.0. The name is the applicable community name.

Default Setting

0.0.0.0

Command Mode

Global Config

7.5.4.8snmp-server enable traps

This command enables the Authentication trap.

Syntax

snmp-server enable traps authentication no snmp-server enable traps authentication

no - This command disables the Authentication trap.

192	Intelligent Blade Panel Module

Image 193

Contents Primergy BX600 Blade Server Systems Primergy BX600 Blade Server Systems Comments… Suggestions… Corrections… Page Contents Intelligent Blade Panel Module Intelligent Blade Panel Module Intelligent Blade Panel Module Information About Boards Important NotesIndustry Canada Class a Compliance StatementsLVD Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class a Introduction Features of the IBP Module Vlan Transparency Supported Features Layer 2 Features Igmp SnoopingSelf-Learning MAC Addresses Automatic Aging for MAC AddressesPort Backup Support Service Vlan & Service LAN SupportUplink Set Support Port Group SupportIBP Module Management Features BootP and Dhcp ClientsSave Configuration as file Various Files of Management OperationConfiguration File Download and Upload Snmp Alarms and Trap LogsCommand Line Interface ProvisionPort Based Authentication Security FeatureLocked Port Support Radius ClientSystem LED Description of HardwareInternal Ports Page Primergy BX620 Primergy GbE Switch Blade 30/12 Internal Ports ListStatus of LEDs Features and BenefitsPort LEDs ConnectivityManagement PerformanceNotational Conventions Target Group Dimensions Technical DataElectrical data National and international standardsEnvironmental conditions Introduction to IBP Network PlanningMaking Network Connections Connecting to 1000BASE-T Devices1000BASE-T Cable Requirements Cable Testing for Existing Category 5 Cable1000BASE-T Pin Assignments Adjusting Existing Category 5 Cabling for 1000BASE-TOverview Package ContentsUnpacking the IBP Module Mount the IBP Module Connecting the IBP ModuleSelect 2 Console Redirection Switch Blade Port Default Settings Start up and Configuration the IBP ModuleUnder Properties, select VT100 for Emulation mode Configuring the TerminalBooting Device Boot Image Download Erasing the Device ConfigurationSoftware Download System Image Download Operation Code CLI Software Download Through Tftp ServerTftp Enter y. The device reboots Overview Non-Configurable Data Configurable DataCommand Buttons Main MenuView Uplink Set Information Groups AdministrationManaging Port Groups Configuring Port Group Configuration Command Buttons Viewing Port Group Information Selection Criteria Viewing Vlan Port Group Information Groups Administration Configurable Data Viewing Service LAN Information Groups Administration Configurable Data Viewing Service Vlan Information Groups Administration Managing Port Backup Configuring Port Backup Configuration Viewing Port Backup Status Groups Administration Panel Settings Menu Panel Settings Menu Viewing Panel Description Page Configurable Data Terminal interface via the EIA-232 port Configuring Inband AdministrationPanel Settings Menu Configuring Telnet Session Page Configurable Data Panel Settings Menu Configuring Serial Port Page Configurable Data Selection Criteria Panel Settings Menu Configuring Dhcp Client-identifier Defining Dhcp Client Configuring Dhcp RestartDefining Snmp Configuring Snmp Community Configuration Configuring Snmp Trap Receiver Configuration Viewing Snmp supported MIBs Panel Settings Menu Panel Settings Menu Viewing Sntp Global Status Non-Configurable Data Configuring Sntp Server Configuration Configurable Data Unknown IPV4 Viewing Sntp Server Status Non-Configurable DataPanel Settings Menu Configurable Data Panel Settings Menu Refresh Refresh the configuration value again Reset All Configuration to Defaults Page Command Buttons Managing System Utilities Panel Reset Command ButtonsReset the Passwords to Defaults Page Command Buttons Configurable Data Uploading Specific Files from Panel Removing Specific File Defining Ping Function Copying Running Configuration to PanelSubmit This will initiate the ping Security Menu Viewing Radius Statistics Page Non-Configurable Data Viewing Radius Server Statistics Page Selection Criteria Security Menu Security Menu Resetting All Radius Statistics Page Command Buttons Configurable Data Security Menu Non-Configurable Data Security Menu Viewing Buffered Log Extended Configuration MenuConfiguring Command Logger Page Configurable Data Viewing Event Log Configuring Console LogConfiguring Hosts configuration Page Configurable Data Configuring syslog configuration Page Configurable Data Extended Configuration Menu Viewing Login Session Page Non-Configurable Data 107 Intelligent Blade Panel Module 108 Intelligent Blade Panel Module 109 Intelligent Blade Panel Module 110 Intelligent Blade Panel Module 111 112 Intelligent Blade Panel Module 113 Intelligent Blade Panel Module Extended Configuration Menu Extended Configuration Menu Viewing Each Port Summary Statistics Page Selection Criteria 117 Intelligent Blade Panel Module 118 Intelligent Blade Panel Module 119 Intelligent Blade Panel Module 120 Intelligent Blade Panel Module Viewing Access Control Summary Page Non-Configurable Data 122 Intelligent Blade Panel Module 123 Intelligent Blade Panel Module Defining Access Control User Login Page Selection Criteria Defining Each Port Access Privileges Page Selection Criteria Extended Configuration Menu Managing IP Filter IP Filter Configuration 128 Intelligent Blade Panel Module Defining User Login 130 Intelligent Blade Panel Module Command CLI Command FormatExample Ip address ipaddr netmask vlan-id Example Clear port-groupParameters 2CLI Mode-based TopologyValues Network Address Syntax Address Type Format Range IPAddr ConventionsMacAddr AnnotationsSystem Information and Statistics commands Show eventlog Show running-configShow sysinfo Show running-config all scriptnameSystem Information Show systemShow hardware Show version Show loginsession Interface Show interface status 4Device Configuration CommandsShow interface status slot/port all Show interface slot/port Show interfaceShow interface counters 142 Intelligent Blade Panel Module Show interface counters detailed slot/port switchport Total Packets Received with MAC Errors Total Packets Received Without ErrorsTotal Packets Transmitted Octets Total Packets Transmitted Successfully Total Transmit ErrorsTotal Transmited Packets Discards 146 Intelligent Blade Panel Module Show interface IBP Show interface switchInterface range InterfaceSpeed-duplex 10 100 full-duplex half-duplex Speed-duplexSpeed-duplex all 10 100 full-duplex half-duplex Full duplex Full duplex half duplex Half duplexNegotiate no negotiate NegotiateNegotiate all no negotiate all Capabilities Storm-control flowcontrol DescriptionStorm-control flowcontrol no storm-control flowcontrol Syntax Show mac-addr-table macaddr all Show mac-address-table igmpsnooping Show mac-address-table multicast macaddr vlanid all Show mac-address-table multicastShow mac-address-table agetime Default Setting Show mac-address-table stats Default SettingShow mac-address-table stats Show mac-address-table agetimeMac-address-table aging-time Igmp Snooping Show Commands Show igmp snoopingIgmpsnooping uplinkSetName no igmpsnooping uplinkSetName Configuration Commands IgmpsnoopingPort Channel Lacp Lacp uplinkSetName no lacp uplinkSetNameShow lacp Uplink Sets Show CommandsUplink-set uplinkSetName no uplink-set uplinkSetName Configuration Commands Uplink-setPort Group Port-group portGroupName no port-group portGroupName Configuration Commands Port-groupPort Backup Show Commands Port-backup uplinkSetName no port-backup uplinkSetName Configuration Commands Port-backupDefault Setting Command Mode Port-backup no port-backupConfiguration Commands Linkstate Link State Show CommandsLinkstate uplinkSetName no linkstate uplinkSetName Vlan Port Groups Show CommandsShow vlan-group vlanGroupName Vlan-group vlanGroupName no vlan-group vlanGroupName Configuration Commands Vlan-group167 Intelligent Blade Panel Module Configuration Commands Svc-lan Service LAN Show CommandsSvc-lan svcLanName no svc-lan svcLanName Configuration Commands Svc-vlan Service Vlan Show CommandsSvc-vlan svcVlanName no svc-vlan svcVlanName Network Commands Show ip interface Management CommandsShow ip redirects 1.4 mtu Show ip filterMtu 1518-9216 no mtu Ip default-gateway Command UsageIp default-gateway gateway no ip default-gateway Ip addressIp address protocol Ip address protocol bootp dhcp vlanID noneIp address mgmt-vlan Ip filter no ip filter Ip filterIp filter ipaddr no ip filter ipaddr Serial Interface Commands Show line consoleBaudrate Line consolePassword-threshold Exec-timeoutPassword-threshold 0-120 no password-threshold Silent-time Telnet Session CommandsTelnet host port debug line echo Line vty Show line vtyExec-timeout 1-160 no exec-timeout Maxsessions 0-5 no maxsessions MaxsessionsSessions Telnet sessions Sessions no sessionsTelnet sessions no telnet sessions Telnet maxsessionsTelnet exec-timeout 1-160 no telnet exec-timeout Telnet exec-timeoutTelnet maxsessions 0-5 no maxsessions Show telnet Snmp Server Commands Show snmpShow trapflags Snmp-server sysname name Snmp-server sysnameSnmp-server location Syntax Snmp-server location locSnmp-server community Snmp-server contactSnmp-server community name no snmp-server community name 190 Intelligent Blade Panel Module Snmp-server community ro rw name Snmp-server host Snmp-server enable trapsSnmp-server host ipaddr name no snmp-server host name No This command disables Multiple User trap Snmp Trap Commands Show snmptrap Snmp trap link-status no snmp trap link-status Snmp trap link-statusSnmp trap link-status all no snmp trap link-status all Snmptrap name ipaddr no snmptrap name ipaddr Snmptrap name ipaddrSnmptrap ipaddr Snmptrap mode name ipaddr no snmptrap mode name ipaddr Snmptrap modeHttp commands Show ip http Snmptrap ipaddr name ipaddr ipaddrnewIp javamode no ip javamode Ip javamodeIp http port 1-65535 no ip http port Ip http portIp http server Ip http server no ip http serverIp http secure-port portid no ip http secure-port Ip http secure-portIp http secure-server Ip http secure-server no ip http secure-serverIp http secure-protocol Secure Shell SSH Commands Show ip sshIp ssh no ip ssh Ip sshIp ssh protocol Ip ssh maxsessions Ip ssh timeoutIp ssh maxsessions 0-5 no ip ssh maxsessions Dhcp Client Commands Ip dhcp restart Ip ssh timeout 1-160 no ip ssh timeoutIp dhcp client-identifier System Burned In MAC Address Lockmessage messagestring default Lock CommandsLock lockidentifier Exclusive no lock lockidentifierALL LockmessageShow lock LockresetShow Commands Show logging System Log Management CommandsShow logging buffered Show logging traplogs Show logging traplogShow logging hosts Display Message Index used for deleting Configuration Commands Logging bufferedLogging buffered no logging buffered Logging console Logging buffered wrap no logging buffered wrapLogging console severitylevel 0-7 no logging console Logging host hostaddress port severitylevel Logging hostLogging syslog Logging host reconfigure hostindex hostaddressLogging syslog no logging syslog Clear logging buffered Logging syslog port portid no logging syslog portScript apply Script Management CommandsScript apply scriptname Script deleteScript show Script listScript show scriptname Show Commands Show users User Account Management CommandsConfiguration Commands Username Username snmpv3 authentication Username username password nopassword no username usernameUsername snmpv3 encryption Show Commands Show users authentication Security CommandsShow authentication Show dot1x Show authentication usersShow dot1x detail Show dot1x statistics slot/port Show dot1x statisticsShow dot1x summary slot/port all Show dot1x summaryShow dot1x users Show radius-servers Secret Configured Yes / NoShow radius Show radius accounting statistics ipaddr Radius Accounting Mode Enabled or disabledShow radius statistics Secret Configured Yes or NoShow radius statistics ipaddr Show tacacs Show port-security Show port-security dynamic slot/port Configuration Commands Authentication login Possible method values are local, radius, reject, and tacacs Username defaultloginUsername login user listname Username login3.2 dot1x default-login 3 Dot1x Configuration Commands 3.1 dot1x initializeDot1x login user listname 3.3 dot1x login3.4 dot1x system-auth-control Dot1x system-auth-control no dot1x system-auth-control3.6 dot1x port-control 3.5 dot1x user3.7 dot1x max-req Dot1x re-authentication no dot1x re-authentication 3.8 dot1x re-authentication3.9 dot1x re-reauthenticate Dot1x max-req 1-10 no dot1x max-req3.10 dot1x timeout Radius accounting mode no radius accounting mode Radius Configuration Commands Radius accounting modeRadius-sever key Radius-server hostRetries the maximum number of times Range 1 Radius-server retransmitRadius-server timeout seconds no radius-server timeout Radius-server timeoutRadius-server msgauth Radius-server primary Tacacs Configuration CommandsTacacs no tacacs Tacacs mode 1-3 master slave no tacacs mode Tacacs modeTacacs server-ip Tacacs server-ip 1-3 ipaddr no tacacs server-ipTacacs port 1-3 1-65535 no tacacs port Tacacs portTacacs key Tacacs key 1-3 no tacacs keyTacacs timeout 1-3 1-255 no tacacs timeout Tacacs timeoutTacacs retry Tacacs retry 1-3 1-9 no tacacs retryPort-security no port-security Default Setting Port Security Configuration Commands Port-securityPort-security max-dynamic Port-security max-static 0-20 no port-security max-static Port-security max-staticPort-security mac-address Syntax Port-security mac-address move Default SettingPort-security mac-address move Show Commands Show sntp Sntp CommandsShow sntp client Configuration Commands Sntp client mode broadcast unicast no sntp client mode Sntp client modeSntp broadcast client poll-interval Sntp client port portid 6-10 no sntp client port Sntp client portSntp unicast client poll-interval Sntp unicast client poll-retry Sntp unicast client poll-timeoutSntp clock timezone Sntp server10.2.9 System UtilitiesSntp clock timezone name 0-12 0-59 before-utc after-utc Clear Clear arpClear eventlog Clear traplogClear pass Clear configClear mac address table Syntax Clear mac-addr-table dynamic Default SettingClear counters Clear counters slot/port allClear igmp snooping Enable passwdClear dot1x statistics Clear ip filterClear dot1x statistics all slot/port Clear tacacs Clear radius statisticsCopy Privileged Exec Files download from PC to board Syntax Copy running-config startup-config filename Delete Copy clibanner url copy url clibanner no clibanner11.4 dir Whichboot Dir boot-rom config opcode filenameBoot-system Display Message Column Heading DescriptionPing Boot-system boot-rom config opcode filenameTraceroute Syntax Logging cli-command Default Setting Logging cli-commandCalendar set Calendar set mm/dd/yy hhmmssReload ConfigureDisconnect Disconnect 0-10 allHostname Promptstring Prompt string Default SettingHostname promptstring QuitIp dhcp client-identifier text text hex hex Dhcp CommandsUsing Snmp Standard MIBs are listed in the following table Supported MIBsPrivate enterprise MIB is listed below RFC 2233 IF-MIB Accessing MIB ObjectsAccessing MIB ObjectsUsing Snmp 279 Intelligent Blade Panel Module Snmp traps supported include the following items Supported TrapsOverview system default settings Default SettingsSSL Default settings for all the configuration commandsPage In-band Administration SSH DSA Key SSH RSA1 Key SSH RSA2 Key Diagnosing IBP Indicators Troubleshooting and TipsSymptom Action Accessing the Management InterfaceInformation on this document

Related manuals

Manual 46 pages 40.75 Kb

Manual 288 pages 28.92 Kb

Manual 274 pages 29.29 Kb