IBM PANEL1173-841 Super IO Device, ¾ Onboard FDC Controller, ¾ Onboard Serial Port 1/2/3/4

Page 53

PANEL1173-841 User’s Manual

zSuper IO Device

Scroll to this item and press <Enter> to view the sub menu Super IO Device.

¾Onboard FDC Controller

Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install and-in FDC or the system has no floppy drive, select Disabled in this field. The options available are Enabled, Disabled.

¾Onboard Serial Port 1/2/3/4

Select an address and corresponding interrupt for the serial port. Options: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto.

¾Serial Port 1/2/3/4 Use IRQ

These items assign which I/O address to access onboard serial port 1/2/3/4.

¾Onboard Paralellel Port

This item allows you to determine access onboard parallel port controller with which I/O address. The options available are 378H/IRQ7, 278H/IRQ5, 3BC/IRQ7, Disabled. The 3BC option does not support any EPP modes.

Phoenix-Award BIOS Utility

45

Image 53

Contents Page All Rights Reserved August 2008, Version A1 Disclaimers‹ FCC Compliance Safety ApprovalsSafety Precautions Trademarks Acknowledgments Table of Contents Vii Memo A p t e r Introduction General Description Powerful computing Intel Core2 Duo processorExpandable for 2 PCI slots Speaker & Wlan antenna supported2 I/O System System SpecificationsMain CPU Board System Specification Operation Temperature Dimension Main Body SizeRelative Humidity Altitude841 DimensionsFront View Front View and I/O Outlets2 I/O Outlets Package List Memo „ Hard Disk Installing the CPU and Dram„ Add-On Card „ Serial Port „ Ethernet „ Mounting WaysHardware Installation Dram CPU Installing the the Hard Disk Drive ¾ Installing Dual 3.5 HDD PANEL1173-841 User’s Manual PANEL1173-841 User’s Manual PANEL1173-841 User’s Manual ¾ Installing 2.5 HDD PANEL1173-841 User’s Manual CD-ROM Installation Add-on Card Installation PANEL1173-841 User’s Manual DVI-I Serial Port InterfaceTXC+ CRT-RED CRT-GREEN CRT-BLUE CRT-HSYNC Vgagnd Ethernet Panel Mounting Mountings Way Panel/ RackRack Mounting Entering Setup A p t e r Phoenix-Award Bios UtilityControl Keys Status Page Setup Menu/Option Page Setup MenuGetting Help Main MenuMain Menu Time Standard Cmos Setup MenuDate Halt On IDE Primary Master/Primary SlaveVideo Advanced Bios Features Hard Disk Boot Priority CPU FeatureCPU L1 & L2 Cache Quick Power On Self TestVirus Warning Boot Other Device First/Second/Third Boot DeviceBoot Up Floppy Seek Boot Up NumLock StatusApic Mode Typematic Delay MsecTypematic Rate Chars/Sec Security OptionSmall Logo EPA Show MPS Version Control For OSMemory Hole At 15M-16M Advanced Chipset FeaturesSystem Bios Cacheable Dvmt Mode VGA Setting PEG/Onchip VGA ControlPCI Express Root Port Func On-Chip Frame Buffer Size Integrated Peripherals Boot Display¾ IDE DMA transfer access ¾ IDE HDD Block ModeOnChip IDE Device ¾ On-Chip Primary/Secondary PCI IDE¾ Legacy Mode Support ¾ Sata Mode¾ IDE Master/Slave PIO ¾ IDE Master/Slave Udma¾ Onboard FDC Controller Super IO Device¾ Onboard Serial Port 1/2/3/4 ¾ Serial Port 1/2/3/4 Use IRQ¾ ECP Mode Use DMA ¾ Parallel Port ModeOnboard Lan1/Lan2 Boot ROM USB Device SettingPower Management Setup Acpi Suspend Type Acpi FunctionPower Management Run Vgabios if S3 ResumeVideo Off Method Video Off In SuspendHDD Power Down Suspend ModePower On by Ring Resume by AlarmPrimary/Secondary IDE 0/1 Reload Global Timer EventsFDD, COM, LPT Port PCI PIRQA-D#Reset Configuration Data 10 PnP/PCI Configuration SetupResources Controlled By IRQ ResourcesPCI Express relative items Maximum Payload Size PCI/VGA Palette SnoopCurrent System Temperature Shutdown TemperatureCurrent CPU Temperature PC Health StatusCPU Clock Ratio Frequency/Voltage ControlAuto Detect PCI Clk Spread SpectrumLoad Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving Memo System A p t e r Driver InstallationTouch Screen SpecificationDriver Installation Windows 2000/XP/Vista Select the Standard Calibrate tab PANEL1173-841 User’s Manual Comm. Port COMn IRQn Driver Installation DOS¾ Identify the Communication Port and IRQ Number ¾ Initializing the PenMount Driver ¾ Do CalibrationMemo Electrical Requirements Power Supply FSP250-50GUB 250W, AC100~240V InputHOLD-UP Time @FULL Load Environmental Requirements EfficiencyReliability Safety