IBM PANEL1173-841 user manual Mountings Way Panel/ Rack, Panel Mounting

Page 35

PANEL1173-841 User’s Manual

2.8Mountings Way – Panel/ Rack

There are two mounting ways available for the PANEL1173-841system: Panel and Rack mounting.

2.8.1Panel Mounting

The PANEL1173-841is designed for panel mount application. To mount the PANEL1173-841, the standard set of mounting kit (included in the system packaging) is needed.

Hardware Installation

27

Image 35

Contents Page All Rights Reserved August 2008, Version A1 Disclaimers‹ FCC Compliance Safety ApprovalsSafety Precautions Trademarks Acknowledgments Table of Contents Vii Memo A p t e r Introduction Speaker & Wlan antenna supported Powerful computing Intel Core2 Duo processorGeneral Description Expandable for 2 PCI slots2 I/O System System SpecificationsMain CPU Board System Specification Altitude Dimension Main Body SizeOperation Temperature Relative Humidity841 DimensionsFront View Front View and I/O Outlets2 I/O Outlets Package List Memo „ Ethernet „ Mounting Ways Installing the CPU and Dram„ Hard Disk „ Add-On Card „ Serial PortHardware Installation Dram CPU Installing the the Hard Disk Drive ¾ Installing Dual 3.5 HDD PANEL1173-841 User’s Manual PANEL1173-841 User’s Manual PANEL1173-841 User’s Manual ¾ Installing 2.5 HDD PANEL1173-841 User’s Manual CD-ROM Installation Add-on Card Installation PANEL1173-841 User’s Manual DVI-I Serial Port InterfaceTXC+ CRT-RED CRT-GREEN CRT-BLUE CRT-HSYNC Vgagnd Ethernet Panel Mounting Mountings Way Panel/ RackRack Mounting Entering Setup A p t e r Phoenix-Award Bios UtilityMain Menu Status Page Setup Menu/Option Page Setup MenuControl Keys Getting HelpMain Menu Time Standard Cmos Setup MenuDate Halt On IDE Primary Master/Primary SlaveVideo Advanced Bios Features Hard Disk Boot Priority CPU FeatureCPU L1 & L2 Cache Quick Power On Self TestVirus Warning Boot Up NumLock Status First/Second/Third Boot DeviceBoot Other Device Boot Up Floppy SeekSecurity Option Typematic Delay MsecApic Mode Typematic Rate Chars/SecSmall Logo EPA Show MPS Version Control For OSMemory Hole At 15M-16M Advanced Chipset FeaturesSystem Bios Cacheable On-Chip Frame Buffer Size VGA Setting PEG/Onchip VGA ControlDvmt Mode PCI Express Root Port FuncIntegrated Peripherals Boot Display¾ On-Chip Primary/Secondary PCI IDE ¾ IDE HDD Block Mode¾ IDE DMA transfer access OnChip IDE Device¾ IDE Master/Slave Udma ¾ Sata Mode¾ Legacy Mode Support ¾ IDE Master/Slave PIO¾ Serial Port 1/2/3/4 Use IRQ Super IO Device¾ Onboard FDC Controller ¾ Onboard Serial Port 1/2/3/4USB Device Setting ¾ Parallel Port Mode¾ ECP Mode Use DMA Onboard Lan1/Lan2 Boot ROMPower Management Setup Acpi Suspend Type Acpi FunctionVideo Off In Suspend Run Vgabios if S3 ResumePower Management Video Off MethodResume by Alarm Suspend ModeHDD Power Down Power On by RingPCI PIRQA-D# Reload Global Timer EventsPrimary/Secondary IDE 0/1 FDD, COM, LPT PortIRQ Resources 10 PnP/PCI Configuration SetupReset Configuration Data Resources Controlled ByPCI Express relative items Maximum Payload Size PCI/VGA Palette SnoopPC Health Status Shutdown TemperatureCurrent System Temperature Current CPU TemperatureSpread Spectrum Frequency/Voltage ControlCPU Clock Ratio Auto Detect PCI ClkLoad Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving Memo System A p t e r Driver InstallationTouch Screen SpecificationDriver Installation Windows 2000/XP/Vista Select the Standard Calibrate tab PANEL1173-841 User’s Manual Comm. Port COMn IRQn Driver Installation DOS¾ Identify the Communication Port and IRQ Number ¾ Initializing the PenMount Driver ¾ Do CalibrationMemo Electrical Requirements Power Supply FSP250-50GUB 250W, AC100~240V InputHOLD-UP Time @FULL Load Environmental Requirements EfficiencyReliability Safety