IBM 22P6972 manual Installing the drive, Opening the computer, Unpacking the drive

Page 14

Installing the drive

Complete the following steps to install the drive:

Step 1. Opening the computer

1.Turn off the computer and all attached devices.

2.Unplug all power cords from the computer and all attached devices.

3.Remove the cover from the computer. Refer to your computer documentation for instructions on removing the computer cover.

Step 2. Unpacking the drive

1.Before opening the antistatic bag that the drive is packed in, touch the bag to an unpainted metal surface for at least two seconds. This drains the static electricity from the package and your body.

2.Remove the drive from the bag.

If you must put the drive down, place the antistatic bag on a flat, padded surface, and place the drive on the antistatic bag.

Step 3. Setting the configuration jumpers

You can configure your drive as master , slave , or cable-select , by placing the jumper over the configuration pins as shown.

Use the following guidelines to determine the correct configuration for your drive.

vConfigure the drive as a master if it will be the only device that is connected to the IDE cable. This is the preset configuration.

vConfigure the drive as a slave if it will be the second device on an IDE cable. Be sure to configure the other device as a master. In some cases, a hard disk drive might require a “master with slave present” jumper setting when another device on the same cable is configured as a slave. For more information on setting configuration jumpers on other devices, refer to the documentation that comes with your computer.

vSome non-IBM computers use special ATA cables with two wires reversed in the device connectors so that the drives can be configured by the cable instead of by jumper position. Use the cable-select position only for computers that are equipped with these special cables. See the documentation that comes with your computer to determine if your ATA adapter requires that you place the jumpers in the cable-select position.

If you place the jumper in the cable-select position, the IDE cable automatically assigns the master and slave settings based on the position of the drive on the cable. You must use the cable-select setting for this cabling system whether the drive is the only device or the second device connected to the cable.

The drive closest to the IDE controller is automatically the master drive. Any other devices on the IDE cable must also be set to cable-select.

1-4IBM Multi-Burner User’s Guide

Page 13 Page 15
Image 14
Page 13 Page 15
Contents IBM Multi- Burner User’s Guide Page IBM Multi- Burner User’s Guide Page Contents Appendix E. Notices Safety Read first Vi IBM Multi-Burner User’s Guide Registering your product Installation and user’s guideAbout this book AppendicesViii IBM Multi-Burner User’s Guide Product description Installation and user’s guideIBM Drive Letter Access DLA Software descriptionBefore you begin Installation requirementsHandling precautions Drive controls and connectors Opening the computer Installing the driveSetting the configuration jumpers Unpacking the driveMounting the drive in the bay Attaching the cables to the driveUsing the drive Completing the hardware installationInstalling the software Using single and double-sided DVD-RAM mediaUsing the drive with CDs and DVDs Removing the disc from the cartridgeUsing the DVD Player Using the DVD Player softwareBefore using the software Securing a disc in a vertically mounted driveClick Intervideo WinDVD Using drive letter access DLAUsing roxio VideoWave Click the General Properties tabCaring for the drive Maintaining the driveCaring for a CD or DVD Installation and user’s guide 12IBM Multi-Burner User’s Guide Power requirements Appendix A. Product specificationsPhysical specifications Environmental requirementsRead speeds Write speedsAppendix B. Problem solving Select Control Panel2IBM Multi-Burner User’s Guide There is no sound from the disc You receive an error messageDisc cannot be read. Take the following actions 4IBM Multi-Burner User’s Guide Enabling DMA for Windows Me Click Settings Click Control PanelClick the Advanced Settings tab Enabling DMA for Windows 2000 ProfessionalClick Control Panel Click Switch to classic view Enabling DMA for Windows XPService and support Appendix D. Warranty informationWarranty period Telephone technical supportSupport 24 hours a day, 7 days a week Without Warranties of ANY Kind 4IBM Multi-Burner User’s Guide Part 2 Country-unique Terms Governing LawHong Kong and Macau EUROPE, Middle EAST, Africa Emea Following Terms Apply to the Country Specified Italy 10IBM Multi-Burner User’s Guide Appendix E. Notices TrademarksIndustry Canada Class B emission compliance statement Electronic emissions noticesFederal Communications Commission FCC statement Avis de conformite a la reglementation d’Industrie CanadaUnione Europea Directiva EMC Conformidad électromagnética European Union emission directiveUnion Européenne Directive Conformité électromagnétique Union Europea Normativa EMC Page Part Number 22P6972
Top Page Image Contents