Cisco Systems WSC2960S24TSSRF, 2960S-24TS-S Master LED, Port LEDs and Modes, Color RPS Status

Page 20

Chapter 1 Product Overview

Front Panel

For information on the System LED colors during power-on self-test (POST), see the “Switch POST Results” section on page 3-1.

RPS LED

Note The RPS LED is not present on the Catalyst 2960S-F48FPS-L, 2960S-F48LPS-L, 2960S-F24PS-L, 2960S-F48TS-L, 2960S-F24TS-L, 2960S-F48TS-S, and 2960S-F24TS-S switches—these models do not support RPS.

 

Table 1-5

 

RPS LED

 

 

 

 

 

 

Color

 

 

RPS Status

 

 

 

 

 

 

Off

 

 

RPS is off or not properly connected.

 

 

 

 

 

 

Green

 

 

RPS is connected and can provide back-up power.

 

 

 

 

 

 

Blinking green

 

RPS is connected but is unavailable. It is providing power to another device

 

 

 

 

(redundancy has been allocated to the other device).

 

 

 

 

 

 

Amber

 

 

The RPS is in standby mode or in a fault condition. See the RPS documentation.

 

 

 

 

 

 

Blinking amber

 

The power supply in a switch has failed, and the RPS is providing power to the

 

 

 

 

switch (redundancy has been allocated to this device).

 

 

 

 

 

For information about the Cisco RPS 2300, see the “Related Publications” section.

Master LED

 

 

 

 

Table 1-6

 

Master LED

 

 

 

 

Port Mode

Description

 

 

 

 

Off

Switch is not the stack master.

 

 

 

 

Green

Switch is the stack master or a standalone switch.

 

 

 

 

Amber

An error occurred when the stack was electing the stack master switch, or another type

 

 

of stack error occurred.

 

 

 

 

 

Port LEDs and Modes

The port and module slots each has a port LED. As a group or individually, the LEDs show information about the switch and about the ports. Table 1-7lists the mode LEDs and their associated port modes and meanings.

Table 1-7 Port Mode LEDs

 

 

 

 

Mode LED

Port Mode

Description

 

 

 

 

 

 

 

 

 

 

 

STAT

Port status

The port status. This is the default mode.

 

 

 

 

 

 

 

 

 

 

 

DUPLX

Port duplex

The port duplex mode: full duplex or half duplex.

 

 

 

 

 

 

Note The ports operate only in full-duplex mode.

 

 

 

 

 

 

 

 

 

 

 

Catalyst 2960-S Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1-12

 

 

 

 

OL-19732-04

 

 

 

 

 

 

 

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Catalyst 2960-S Switch Hardware Installation Guide Americas HeadquartersPage N T E N T S Connecting to Fiber-Optic SFP and SFP+ Modules Uninstalling the Cisco Microsoft Windows USB Driver C-5 Catalyst 2960-S Switch Hardware Installation Guide Preface Obtaining Documentation and Submitting a Service Request Related PublicationsDescription Switch ModelsSupported Switch Model Front Panel Catalyst 2960S-48FPD-L Front PanelCatalyst 2960S-48TS-L Front Panel Catalyst 2960S-F48FPS-L Front Panel 10/100 PoE+ Ports 10/100/1000 PoE+ Ports10/100 Ports 10/100/1000 PortsManagement Ports USB Mini-Type B PortUSB Type a Port SFP and SFP+ Module SlotsSupported SFP Modules Supported SFP+ Modules SFP-10G-LRM=SFP-H10GB-CU1M= SFP-H10GB-CU3M=LEDs System LEDRPS 1 LED Color System StatusPort Mode Description Mode LED Port Mode DescriptionMaster LED Port LEDs and ModesPort Mode Port LED Color Meaning SpeedStack Color PoE Status10/100 and 10/100/1000 ports Stack LED Stack member 1 3 Stack memberColor Description Console LEDsConsole LEDs show which console port is in use Rear Panel Ethernet Management Port LEDFan exhaust AC power connector RPS connector 12 Catalyst 2960-S Switch Rear Panel with an RPS connectorRPS Connector Fan exhaust AC power connectorFlexStack Ports Cisco RPSAC Power Connector Management OptionsNetwork Configurations OL-19732-04 Preparing Safety WarningsRead these topics and perform the procedures in this order PWR-RPS2300Statement 113F 45C. Statement Tools and Equipment Installation GuidelinesBox Contents Stack Guidelines Planning a Switch StackVerifying Switch Operation Switch Installation Planning a Switch Stack Installing the FlexStack Module Secure the screws tightly on each side of the moduleStack Cabling Stack Bandwidth and Partitioning ExamplesStack with Half Bandwidth Connections Rack-Mounting Installing the SwitchPower-On Sequence for Switch Stacks Attaching the Rack-Mount Brackets 10 Rack-Mounting Brackets12 Attaching Brackets for 19-inch Racks Mounting in a Rack 13 Mounting in a RackPhillips truss-head screws Wall-MountingAttaching the Brackets for Wall-Mounting Attaching the RPS Connector Cover StatementMounting on a Wall 16 Mounting on a WallTable- or Shelf-Mounting Connecting the FlexStack CablesAfter Switch Installation Installing the Power Cord Retainer Optional 18 Inserting the Retainer through the Lanced LoopSlide the retainer through the first latch. See Figure 19 Sliding the Retainer Through the LatchInstalling SFP and SFP+ Modules 21 Sleeve Around the Power CordInstalling an SFP or SFP+ Module Removing an SFP or SFP+ ModuleConnecting to SFP and SFP+ Modules Connecting to Fiber-Optic SFP and SFP+ ModulesConnecting to 1000BASE-T SFP 24 Connecting to a Fiber-Optic SFP Module PortRJ-45 connector 10/100 and 10/100/1000 PoE+ Port ConnectionsSwitch to switch Yes Switch to hub Device Crossover Cable1Device Crossover Cable Where to Go Next10/100 and 10/100/1000 Port Connections Switch LEDs Diagnosing ProblemsSwitch Post Results Switch Connections Bad or Damaged CableEthernet and Fiber-Optic Cables Link StatusInterface Settings 10/100 or 10/100/1000 Port Connections10/100 or 10/100/1000 PoE Port Connections SFP and SFP+ ModuleSwitch Performance Ping End DeviceSpanning Tree Loops Speed, Duplex, and AutonegotiationCabling Distance Clearing the Switch IP Address and ConfigurationFinding the Switch Serial Number Troubleshooting Finding the Switch Serial Number Serial Number Location for the C2960S-STACK Module Serial Number Location for the C2960S-F-STACK Module Replacing a Failed Stack Member OL-19732-04 Technical Specifications Environmental RangesPower Requirements Physical Dimensions Power Requirements Physical Dimensions OL-19732-04 Connector Specifications 10/100 Ports Including PoESFP Module Connectors 10/100/1000 Ports Including PoECables and Adapters SFP Module Cables1000BASE-SX GLC-SX-MMGLC-T 1000BASE-LX/LHTwo Twisted-Pair Straight-Through Cable Schematic Cable PinoutsDevice Switch Console RJ-45-to-DB-9 Port DTEConsole Port Adapter Pinouts Switch Console RJ-45-to-DB-25 Port DTE OL-19732-04 Accessing the CLI Through Express Setup Accessing the CLI Through the Console PortConnecting the RJ-45 Console Port or USB Console Port Installing the Cisco Microsoft Windows USB Device Driver Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows Vista USB DriverUninstalling the Cisco Microsoft Windows USB Driver Uninstalling the Cisco Microsoft Windows Vista USB DriverCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable password, and press Return Enter a virtual terminal Telnet password, and press ReturnApplication. To configure Snmp later, enter no Switch or as a standalone switchThese choices appear Numerics 10/100/1000 PoE ports NumberingRack-mounting 2-10 to SFP and SFP+ modules IN-2LED RPSStatus Post Restricted access area RPS connector cover IN-6
Related manuals
Manual 16 pages 38.2 Kb Manual 108 pages 14.27 Kb Manual 28 pages 25.34 Kb

2960S, WSC2960S24TSSRF, 2960S-24TS-S, 2960 specifications

Cisco Systems 2960 series switches are a prominent solution in the networking landscape, known for their reliability, scalability, and feature-rich offerings. Ideal for small to medium-sized enterprises, these switches provide a robust foundation for network infrastructure, ensuring optimal performance and connectivity.

One of the standout features of the Cisco 2960 series is its Layer 2 switching capabilities. The switches support multiple VLANs (Virtual Local Area Networks), allowing network administrators to segment traffic efficiently and enhance security protocols. This is crucial in modern networks where managing traffic and isolating sensitive information is a priority.

The Cisco 2960 series also incorporates advanced Quality of Service (QoS) features, enabling the prioritization of critical applications and services. This functionality ensures that time-sensitive data, such as voice and video traffic, maintains a high quality of service even in congested networks. With support for IEEE 802.1p and DSCP marking, administrators can fine-tune their network performance to meet specific organizational needs.

Power over Ethernet (PoE) is another significant characteristic of the Cisco 2960 series. This feature allows switches to deliver electrical power alongside data over Ethernet cables to devices such as IP phones, wireless access points, and surveillance cameras. With PoE, organizations can reduce clutter from power cables and increase deployment flexibility for various devices.

In terms of security, the Cisco 2960 series is equipped with a range of integrated security features. The switch supports port security, 802.1X authentication, and Access Control Lists (ACLs), providing robust defenses against unauthorized access and potential network vulnerabilities. These security measures are essential for protecting sensitive data and ensuring compliance with industry regulations.

Moreover, the Cisco 2960 series offers enhanced network management capabilities with Cisco's Intelligent Network Services. This includes support for Simple Network Management Protocol (SNMP), Cisco Prime, and Embedded Event Manager (EEM), allowing for efficient monitoring, troubleshooting, and policy enforcement across the network.

Additionally, the Cisco 2960 switches provide various models and configurations, catering to different networking needs. Options include models with varying port densities, uplink configurations, and stacking capabilities, making it easy for organizations to choose solutions that align perfectly with their requirements.

In summary, the Cisco 2960 series is a versatile and essential component of modern networking environments. Its advanced features, including Layer 2 support, QoS, PoE, robust security, and diverse management tools, make it an excellent choice for organizations looking to build a strong and secure network infrastructure.
Top Page Image Contents