Cisco Systems 78-16019-02 manual Examples, Switch# show redundancy summary

Page 21

Chapter 3 Initial Configuration

Configuring CPU Switch Module Redundancy

Examples

The following example shows the CPU switch module redundancy configuration and status:

Switch# show redundancy summary

Redundant system information

 

----------------------------

 

Available Uptime:

3 days, 4 hours, 35 minutes

Time since last switchover:

10 hours, 30 minutes

Switchover Count:

1

Inter-CPU Communication State:UP

Last Restart Reason:

Switch over

Software state at switchover:

ACTIVE

Last Running Config sync:

2 hours, 18 minutes

Running Config sync status:

In Sync

Last Startup Config sync:

6 hours, 4 minutes

Startup Config sync status:

In Sync

This CPU

is the Active CPU.

 

-------------------------------

Slot:

 

7

Time since CPU Initialized:

22 hours, 33 minutes

Image Version:

ONS-15530 Software(ONS15530-I-M),...

Image File:

bootflash:ons15530-i-mz.010727

Software

Redundancy State:

ACTIVE

Hardware

State:

ACTIVE

Hardware

Severity:

0

Peer CPU

is the Standby CPU.

 

-------------------------------

Slot:

 

6

Time since CPU Initialized:

10 hours, 29 minutes

Image Version:

ONS-15530 Software(ONS15530-I-M),...

Image File (on sby-CPU):

bootflash:ons15530-i-mz.010727

Software

Redundancy State:

STANDBY HOT

Hardware

State:

STANDBY

Hardware

Severity:

0

 

 

Cisco ONS 15530 Configuration Guide and Command Reference

 

 

 

 

 

 

78-16019-02, Cisco IOS Release 12.2(18)SV2

 

 

3-21

 

 

 

 

 

Image 21
Contents About the CPU Switch Module Initial ConfigurationYou can now begin configuring the CPU switch module Using the Console Ports, NME Ports, and Auxiliary PortsStarting Up the Cisco ONS You see the following user Exec promptEnable Password About PasswordsEnable Secret Password Modem SupportCommand Purpose Configuring IP Access on the NME InterfaceDisplaying the NME Interface Configuration Displaying the Operating Configurations Configuring the Host NameSwitch# configure terminal Switchconfig# hostname name Specifies a system nameSwitch# configure terminal Switchconfig# hostname ONS15530 ONS15530# copy systemrunning-config nvramstartup-configAbout NTP Displaying the NTP Configuration Configuring NTPCommand Example PurposeConfiguring AAA Configuring Security FeaturesConfiguring Authentication Configuring AuthorizationConfiguring Radius Configuring KerberosConfiguring TACACS+ Configuring Traffic Filters and FirewallsConfiguring Passwords and Privileges About CPU Switch Module Redundancy State Description CPU Switch Module State Transition DiagramRedundant Operation Requirements Configuring CPU Switch Module Redundancy Forcing a Switchover from Privileged Exec ModeRedundancy switch-activity force Switchover Forcing a Switchover from ROM Monitor ModeDisplaying the Autoboot Configuration Configuring AutobootSwitchconfig# config-register Bootflash filenameSynchronizing the Configurations Synchronizing Configurations ManuallyFollowing example shows the contents of the boot variable Switchconfig-red# no auto-sync running-config Filename When SynchronizedSwitchconfig-red# no auto-sync startup-config Enabling and Disabling Automatic SynchronizationShow redundancy running-config-file Configuring Maintenance ModeShow redundancy summary Show redundancy capabilityExamples Switch# show redundancy summarySwitch# show redundancy capability Following example shows the CPU switch module capabilitiesReloading the CPU Switch Modules Sby-Switch#show redundancy running-config-fileSwitch# redundancy reload peer Enables access to privileged Exec mode from Switchconfig-red# standby privilege-modeEnable Standby CPU switch module CLI. The default stateDown About the Software Configuration RegisterSoftware Configuration Register Settings 4describes each of the software configuration register bitsBit Number Hexadecimal Description Boot Field Values Bit Address nethostBit Baud Rate Boot Command Default System Boot Behavior7describes the values for the boot field Boot Field Value DescriptionVerify the Configuration Register Value Changing the Software Configuration RegisterSwitch# show version Displays the current configuration register valueConfiguring Fan Failure Shutdown Switchconfig# environment-monitor shutdown fanAbout Fan Failure Shutdown Switch# show environment Displaying the Fan Tray Failure Shutdown Configuration78-16019-02, Cisco IOS Release 12.218SV2