Cisco Systems 78-16019-02 manual Reloading the CPU Switch Modules, Switch# redundancy reload peer

Page 23

Chapter 3 Initial Configuration

Configuring CPU Switch Module Redundancy

deviation_numbers_str	YES	N/A	N/A
manufacturing_use	YES	0	0
rma_number_str	YES
rma_failure_code_str	YES
oem_str	YES	Cisco	Cisco
clei_str	YES	TBD	TBD
snmp_oid_substr	YES	TBD	TBD
schematic_num_str	YES	92-4568-03	92-4568-03
Backplane IDPROM field	Match	Local CPU	Peer CPU
---------------------------	-----	-------------------- --------------------
hardware_major_version	YES	3	3
hardware_minor_version	YES	1	1
engineering_use_str	YES	LAB Prototype	LAB Prototype
crc16	OK	52960	10284
user_track_string	NO	hello PhyAlias	test AssetTag123
			lab
diagst	YES	^A	^A
board_specific_revision	YES	1	1
board_specific_magic_number	YES	153	153
board_specific_length	YES	56	56
mac_address_block_size	YES	16	16
mac_address_base_str	YES	00016447a240	00016447a240
cpu_number	OK	0	1
optical_backplane_type	YES	255	255

The following example shows how to display the running configuration file on the standby CPU switch module:

sby-Switch#show redundancy running-config-file

!

version 12.1 no service pad

service timestamps debug uptime service timestamps log uptime no service password-encryption no service dhcp

!

hostname Switch

<Information deleted>

Reloading the CPU Switch Modules

To reload one or both of the CPU switch modules, use the following privileged EXEC commands on the active CPU switch module CLI:

Command	Purpose

redundancy reload peer	Reloads the standby CPU switch module.

redundancy reload shelf	Reloads both CPU switch modules in the shelf.

Example

The following example shows how to reload the standby CPU switch module:

Switch# redundancy reload peer

Reload peer [confirm] y

Preparing to reload peer


		Cisco ONS 15530 Configuration Guide and Command Reference
		Cisco ONS 15530 Configuration Guide and Command Reference
	78-16019-02, Cisco IOS Release 12.2(18)SV2			3-23
	78-16019-02, Cisco IOS Release 12.2(18)SV2			3-23

Image 23

Contents About the CPU Switch Module Initial ConfigurationYou see the following user Exec prompt Using the Console Ports, NME Ports, and Auxiliary PortsYou can now begin configuring the CPU switch module Starting Up the Cisco ONSModem Support About PasswordsEnable Password Enable Secret PasswordCommand Purpose Configuring IP Access on the NME InterfaceDisplaying the NME Interface Configuration Switchconfig# hostname name Specifies a system name Configuring the Host NameDisplaying the Operating Configurations Switch# configure terminalAbout NTP Switch# configure terminal Switchconfig# hostname ONS15530ONS15530# copy systemrunning-config nvramstartup-config Example Purpose Configuring NTPDisplaying the NTP Configuration CommandConfiguring Authorization Configuring Security FeaturesConfiguring AAA Configuring AuthenticationConfiguring Radius Configuring KerberosConfiguring Passwords and Privileges Configuring TACACS+Configuring Traffic Filters and Firewalls About CPU Switch Module Redundancy State Description CPU Switch Module State Transition DiagramRedundant Operation Requirements Redundancy switch-activity force Configuring CPU Switch Module RedundancyForcing a Switchover from Privileged Exec Mode Switchover Forcing a Switchover from ROM Monitor ModeBootflash filename Configuring AutobootDisplaying the Autoboot Configuration Switchconfig# config-registerFollowing example shows the contents of the boot variable Synchronizing the ConfigurationsSynchronizing Configurations Manually Enabling and Disabling Automatic Synchronization Filename When SynchronizedSwitchconfig-red# no auto-sync running-config Switchconfig-red# no auto-sync startup-configShow redundancy capability Configuring Maintenance ModeShow redundancy running-config-file Show redundancy summaryExamples Switch# show redundancy summarySwitch# show redundancy capability Following example shows the CPU switch module capabilitiesSwitch# redundancy reload peer Reloading the CPU Switch ModulesSby-Switch#show redundancy running-config-file Standby CPU switch module CLI. The default state Switchconfig-red# standby privilege-modeEnables access to privileged Exec mode from EnableDown About the Software Configuration RegisterBit Number Hexadecimal Description Software Configuration Register Settings4describes each of the software configuration register bits Bit Baud Rate Boot Field ValuesBit Address nethost Boot Field Value Description Default System Boot BehaviorBoot Command 7describes the values for the boot fieldDisplays the current configuration register value Changing the Software Configuration RegisterVerify the Configuration Register Value Switch# show versionAbout Fan Failure Shutdown Configuring Fan Failure ShutdownSwitchconfig# environment-monitor shutdown fan Switch# show environment Displaying the Fan Tray Failure Shutdown Configuration78-16019-02, Cisco IOS Release 12.218SV2