Cisco Systems Cisco 7000, Cisco 7507 List of Parts and Tools, Tools Required, Parts List

Page 15

Prerequisites

List of Parts and Tools

This section lists the tools you will need to complete this installation and the parts that are shipped as part of the rack-mount kit. Ensure that you have all the tools and parts required so that you can complete the installation without interruption.

Tools Required

You will need the following tools to install the mounting hardware and chassis in the rack:

•

•

•

•

Number 2 Phillips screwdriver

One 7/16-inch, open-end (or adjustable) wrench if you will remove the chassis feet

Tape measure or level (both optional)

Ohmmeter if your installation requires the chassis to be electrically isolated from the rack

You also need the following tools to replace the power supplies after mounting the chassis:

•A number 2 Phillips or 1/4-inch, flat-blade screwdriver for the captive screw. (Because of ongoing product improvements, some power supplies use slotted screws, and others use Phillips screws.)

•If cables from other equipment fall in front of the power supply bays, you will need cable ties to temporarily anchor the cables out of the way while you install the power supplies.

Before beginning the power supply installation, check the captive installation screws on all power supplies to determine which tools you will need.

Parts List

Table 1 lists the parts that are included in the rack-mount kit. To verify that you received all the parts listed, refer to Table 1 and to Figure 2 on page 4. If any are missing, contact a service representative for assistance. (Refer to the section “Cisco Information Online” at the end of this document.)

Table 1

Rack-Mount Kit Parts Checklist

 

 

 

 

Quantity

Part Description

Received

 

 

 

2

Mounting brackets (left and right are identical), each with an attached spanner bar

 

 

 

 

2

Chassis ears with captive grommets (left and right ears are identical)

 

 

 

 

4

M4 x 10-mm LG Phillips flat-head screws

 

 

 

 

10

10-32 x 5/8'' LG Phillips pan-head screws with integral square cone washers

 

 

 

 

Note As you perform the installation, refer to Figure 2, on page 4, and to the detailed illustrations that follow.

Cisco 7000 and Cisco 7507 Rack-Mount Kit Installation Instructions 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Doc. No Equipment Rack Descriptions Rack-Mount Kit OverviewMounting Kit Hardware Rack-Mount Installation SummaryShows the components in this mounting kit Typical Center-Mount Installation Shows a typical flush-mount installation Prerequisites Safety Guidelines Working with Electrical EquipmentLifting the Chassis Safely Lifting Safely Safety with Electricity Equipment Rack Considerations Power Supply Safety Interlocks-AC-Input Power Supply Shown Power supply/interface processor end Rack Stability Plastic front panel end Chassis Center of Gravity for Flush-Mount Configurations Rack Ventilation Rack Dimensions and Site LayoutParts List List of Parts and ToolsTools Required Installing the Brackets InstallationMounting the Brackets to the Rack Posts Installing a Bracket on a Rack Post-Left Bracket ShownSecuring the Spanner Bars Positioning and Fastening a Spanner Bar Attaching the Chassis Ears Installing the Ears on the ChassisRemoving Power Supplies and Interface Cables Installing the Chassis in the RackMoving the Chassis into the Rack Handling a Power Supply AC-Input Power Supply ShownChassis Foot Underside of chassisSliding the Chassis into the Rack Checking Electrical IsolationReplacing Power Supplies and Interface Cables Restarting the System Router name Prepared by Location Date Slot Circle one Chassis serial number Slot Circle oneRouter name Prepared by Location Date RSP2Power Supply Warning Power Disconnection WarningPower Supply Disconnection Warning Electric Shock Warning Chassis Lifting Warning DC Power Disconnection Warning Lightning Activity Warning Chassis Warning-Rack-Mounting and Servicing Translated Safety Warnings Ramp Warning Cisco Information Online
Top Page Image Contents