Cisco Systems PA-2FE-FX, PA-2FE-TX manual Preparing for Installation, Required Tools and Equipment

Page 33

C H A P T E R 2

Preparing for Installation

This chapter describes the general equipment, safety, and site preparation requirements for installing the PA-2FE. This chapter contains the following sections:

•Required Tools and Equipment, page 2-1

•Software and Hardware Requirements, page 2-2

•Checking Hardware and Software Compatibility, page 2-2

•Safety Guidelines, page 2-3

•FCC Class A Compliance, page 2-10

Required Tools and Equipment

You need the following tools and parts to install a PA-2FE. If you need additional equipment, contact a service representative for ordering information.

•PA-2FE-TX or PA-2FE-FX

•VIP (for installation in Cisco 7500 series chassis only)

•Cisco 7304 PCI port adapter carrier card (for installation in Cisco 7304 router only)

•Cables appropriate for the PA-2FE interfaces (RJ-45 and multimode optical-fiber cables are not available from Cisco; they are available from commercial vendors.)

•Number 1 Phillips and a 3/16-inch flat-blade screwdriver (for VIP installation only)

•Number 2 Phillips screwdriver

•Your own electrostatic discharge (ESD)-prevention equipment or the disposable grounding wrist strap included with all upgrade kits, field-replaceable units (FRUs), and spares

•Antistatic mat

•Antistatic container

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

 

OL-3474-07

2-1

 

 

 

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Text Part Number OL-3474-07 Americas HeadquartersCisco Systems, Inc. All rights reserved N T E N T S Adapter Using the ping Command to Verify Network Connectivity OL-3474-07 Document Version Date Change Summary Document Revision HistoryOrganization ObjectivesRelated Documentation Section Title DescriptionPreface Related Documentation Preface Related Documentation Fast Ethernet Port Adapter Family PA-FE and PA-2FE Datasheet Xii Port Adapter Overview OverviewFast Ethernet Overview Ieee 802.3u 100BASE-T SpecificationsParameter 100BASE-FX MultimodeDTE* DTE LEDs Receptacles, Cables, and PinoutsLED Label Color State Function Pin Description RJ-45 Port and ConnectorNetwork Management PA-2FE-FX Duplex SC ConnectorCisco 7100 Series Routers Slot Numbering Port Adapter Slot Locations on the Supported Platforms11 Port Adapter Slots in the Cisco 7140 Series Router 13 Port Adapter Slots in the Cisco uBR7246VXR Router Cisco uBR7200 Series Router Slot NumberingCisco 7301 Router Slot Numbering Cisco 7201 Router Slot NumberingSlot Cisco 7304 PCI Port Adapter Carrier Card Slot NumberingCisco 7500 Series Routers with VIP Slot Numbering Cisco 7401ASR Router Slot NumberingRSP VIP interface-slot RSP-slot 5 7 9 11 Platform Interface Address Format Numbers Syntax Identifying Interface AddressesCisco 7120 Router and Cisco 7140 Router Interface Addresses Cisco 7201 Router Interface Addresses Cisco uBR7200 Series Routers Interface AddressesCisco 7301 Router Interface Addresses Cisco 7401ASR Router Interface AddressesCisco 7500 Series Routers VIP Interface Addresses OL-3474-07 Required Tools and Equipment Preparing for InstallationSoftware and Hardware Requirements Checking Hardware and Software CompatibilityPlatform Recommended Minimum Cisco IOS Release Safety Warnings Safety GuidelinesWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Guarde Estas Instrucciones GEM Disse Anvisninger Page Electrical Equipment Guidelines Preventing Electrostatic Discharge Damage Telephone Wiring GuidelinesFCC Class a Compliance Handling Port Adapters Removing and Installing Port AdaptersHandling a Port Adapter Online Insertion and RemovalRemoving and Installing Port Adapters Port Adapter Removal and Installation Step Cisco 7100 Series-Removing and Installing a Port AdapterRemoval applies to any Cisco uBR7200 Series Routers-Removing a Port Adapter Metal carrier PC board Cisco uBR7200 Series Routers-Installing a Port AdapterCisco 7201 Router-Removing and Installing a Port Adapter Cisco 7301 Router-Removing and Installing a Port Adapter Page CC-PA Cisco 7401ASR Router-Removing and Installing a Port Adapter Captive installation screw With the screw removed, grasp Connecting a PA-2FE-TX RJ-45 Cable-Horizontal Orientation Connecting a PA-2FE RJ-45 or SC CableConnecting PA-2FE-FX SC Cables-Horizontal Orientation OL-3474-07 Using the Exec Command Interpreter Configuring the PA-2FEShutting Down an Interface Configuring the InterfacesFastethernet and slot/port Platform Command ExampleAdapter/port Show interfaces fastethernet Slot-number/port-number Performing a Basic Interface Configuration Fastethernet Checking the Configuration Using show Commands to Verify the New Interface StatusCommand Function Example Command Function Example Using the show version or show hardware Commands Cisco 7201 Router-Example Output of the show version Command Last reset from power-on 1 FastEthernet interface Using the show diag Command Show diag Cisco 7201 Router-Example Output of the show diag Command 0x3060 Using the show interfaces Command Configuring the PA-2FE Checking the Configuration Router# show interfaces Router# ping Using the ping Command to Verify Network ConnectivityConfiguring the PA-2FE Checking the Configuration

PA-2FE-FX, PA-2FE-TX specifications

Cisco Systems PA-2FE-TX and PA-2FE-FX are high-performance Ethernet interface modules designed to enhance the capabilities of Cisco 2600 and 3600 series routers. They provide businesses with flexible and reliable networking solutions that meet the increasing demand for bandwidth and connectivity.

One of the main features of the PA-2FE-TX module is its ability to support two 10/100 Mbps Fast Ethernet interfaces. This allows organizations to connect multiple devices while improving network performance. The PA-2FE-FX module, on the other hand, is designed for optical fiber connections. It features two Fast Ethernet interfaces that utilize an SC connector for easier cable management in fiber optic environments. This capability facilitates long-distance data transmission, making it suitable for backbone connections or inter-building links.

Both modules incorporate advanced technologies to ensure efficient data handling. They support Cisco's Auto-Negotiation feature, enabling devices to automatically select the optimal speed and duplex settings, thus simplifying deployment and reducing configuration errors. This functionality is vital in environments with varied device capabilities, allowing seamless communication across the network.

The PA-2FE-TX and PA-2FE-FX modules utilize Quality of Service (QoS) capabilities to prioritize traffic, ensuring that critical applications receive the necessary bandwidth. This is particularly beneficial for VoIP services, video conferencing, and other latency-sensitive applications. Additionally, the modules offer support for VLANs, allowing organizations to segment their networks effectively and enhance security by isolating sensitive data traffic.

Another important characteristic of these modules is their hot-swappable nature, enabling users to replace them without powering down the router, thus minimizing downtime. This feature is critical for businesses that require high availability and reliability from their networking equipment.

In summary, the Cisco Systems PA-2FE-TX and PA-2FE-FX interface modules stand out for their versatility, enabling businesses to implement customized networking solutions tailored to specific needs. With support for both copper and fiber connections, advanced QoS features, and seamless integration into existing Cisco routers, these modules reinforce Cisco’s commitment to providing innovative, robust network solutions that cater to the demands of modern enterprise environments.
Top Page Image Contents