Cisco Systems PA-2FE-TX, PA-2FE-FX manual Connecting a PA-2FE RJ-45 or SC Cable

Page 58

Chapter 3 Removing and Installing Port Adapters

Connecting a PA-2FE RJ-45 or SC Cable

Connecting a PA-2FE RJ-45 or SC Cable

To continue your PA-2FE port adapter installation, you must install the port adapter’s interface cables. The following instructions apply to all supported platforms.

RJ-45 and SC-type fiber-optic cables are not available from Cisco; they are available from commercial cable vendors.

Use the following procedure to connect RJ-45 or SC cables:

Step 1 If you have RJ-45 connections (PA-2FE-TX), attach the Category 5 unshielded twisted-pair (UTP) cable directly to an RJ-45 port on the PA-2FE-TX. (See Figure 3-3.) The PA-2FE is an end-station device and not a repeater. You must connect the PA-2FE to a transceiver, switch, hub, repeater, DTE, or back-to-back to another 10/100-Mbps Fast Ethernet adapter.

If you have SC connections (PA-2FE-FX), attach the cable directly to an SC port on the PA-2FE-FX. (See Figure 3-4.) Use either one duplex SC connector or two simplex SC connectors, and observe the correct relationship between the receive (RX) and transmit (TX) ports on the PA-2FE-FX and your repeater.

Note Port adapters have a handle attached, but this handle is not shown to allow a full detailed view of each port adapter’s faceplate.

Caution Only connect cables that comply with EIA/TIA-568 standards. (See the “Receptacles, Cables, and Pinouts” section on page 1-4for cable recommendations and specifications.)

Step 2 Attach the network end of your RJ-45 or SC-type cable to your 10/100BASE-T transceiver, switch, hub, repeater, DTE, or other external 10/100BASE-T equipment.

Figure 3-3 Connecting a PA-2FE-TX RJ-45 Cable—Horizontal Orientation

0

PA-2FE-TX

1

46455

RJ-45 cable

RJ-45 cable

To repeater

To repeater

or DTE

or DTE

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

3-16

OL-3474-07

 

 

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Americas Headquarters Text Part Number OL-3474-07Cisco Systems, Inc. All rights reserved N T E N T S Adapter Using the ping Command to Verify Network Connectivity OL-3474-07 Document Revision History Document Version Date Change SummaryRelated Documentation ObjectivesOrganization Section Title DescriptionPreface Related Documentation Preface Related Documentation Fast Ethernet Port Adapter Family PA-FE and PA-2FE Datasheet Xii Overview Port Adapter OverviewParameter Ieee 802.3u 100BASE-T SpecificationsFast Ethernet Overview 100BASE-FX MultimodeDTE* DTE Receptacles, Cables, and Pinouts LEDsLED Label Color State Function RJ-45 Port and Connector Pin DescriptionPA-2FE-FX Duplex SC Connector Network ManagementPort Adapter Slot Locations on the Supported Platforms Cisco 7100 Series Routers Slot Numbering11 Port Adapter Slots in the Cisco 7140 Series Router Cisco uBR7200 Series Router Slot Numbering 13 Port Adapter Slots in the Cisco uBR7246VXR RouterCisco 7201 Router Slot Numbering Cisco 7301 Router Slot NumberingCisco 7304 PCI Port Adapter Carrier Card Slot Numbering SlotCisco 7401ASR Router Slot Numbering Cisco 7500 Series Routers with VIP Slot NumberingRSP VIP interface-slot RSP-slot 5 7 9 11 Identifying Interface Addresses Platform Interface Address Format Numbers SyntaxCisco 7120 Router and Cisco 7140 Router Interface Addresses Cisco 7301 Router Interface Addresses Cisco uBR7200 Series Routers Interface AddressesCisco 7201 Router Interface Addresses Cisco 7401ASR Router Interface AddressesCisco 7500 Series Routers VIP Interface Addresses OL-3474-07 Preparing for Installation Required Tools and EquipmentChecking Hardware and Software Compatibility Software and Hardware RequirementsPlatform Recommended Minimum Cisco IOS Release Safety Guidelines Safety WarningsAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Guarde Estas Instrucciones GEM Disse Anvisninger Page Electrical Equipment Guidelines Telephone Wiring Guidelines Preventing Electrostatic Discharge DamageFCC Class a Compliance Removing and Installing Port Adapters Handling Port AdaptersOnline Insertion and Removal Handling a Port AdapterRemoving and Installing Port Adapters Port Adapter Removal and Installation Cisco 7100 Series-Removing and Installing a Port Adapter StepRemoval applies to any Cisco uBR7200 Series Routers-Removing a Port Adapter Cisco uBR7200 Series Routers-Installing a Port Adapter Metal carrier PC boardCisco 7201 Router-Removing and Installing a Port Adapter Cisco 7301 Router-Removing and Installing a Port Adapter Page CC-PA Cisco 7401ASR Router-Removing and Installing a Port Adapter Captive installation screw With the screw removed, grasp Connecting a PA-2FE RJ-45 or SC Cable Connecting a PA-2FE-TX RJ-45 Cable-Horizontal OrientationConnecting PA-2FE-FX SC Cables-Horizontal Orientation OL-3474-07 Configuring the PA-2FE Using the Exec Command InterpreterConfiguring the Interfaces Shutting Down an InterfacePlatform Command Example Fastethernet and slot/portAdapter/port Show interfaces fastethernet Slot-number/port-number Performing a Basic Interface Configuration Fastethernet Using show Commands to Verify the New Interface Status Checking the ConfigurationCommand Function Example Command Function Example Using the show version or show hardware Commands Cisco 7201 Router-Example Output of the show version Command Last reset from power-on 1 FastEthernet interface Using the show diag Command Show diag Cisco 7201 Router-Example Output of the show diag Command 0x3060 Using the show interfaces Command Configuring the PA-2FE Checking the Configuration Router# show interfaces Using the ping Command to Verify Network Connectivity Router# pingConfiguring the PA-2FE Checking the Configuration

PA-2FE-FX, PA-2FE-TX specifications

Cisco Systems PA-2FE-TX and PA-2FE-FX are high-performance Ethernet interface modules designed to enhance the capabilities of Cisco 2600 and 3600 series routers. They provide businesses with flexible and reliable networking solutions that meet the increasing demand for bandwidth and connectivity.

One of the main features of the PA-2FE-TX module is its ability to support two 10/100 Mbps Fast Ethernet interfaces. This allows organizations to connect multiple devices while improving network performance. The PA-2FE-FX module, on the other hand, is designed for optical fiber connections. It features two Fast Ethernet interfaces that utilize an SC connector for easier cable management in fiber optic environments. This capability facilitates long-distance data transmission, making it suitable for backbone connections or inter-building links.

Both modules incorporate advanced technologies to ensure efficient data handling. They support Cisco's Auto-Negotiation feature, enabling devices to automatically select the optimal speed and duplex settings, thus simplifying deployment and reducing configuration errors. This functionality is vital in environments with varied device capabilities, allowing seamless communication across the network.

The PA-2FE-TX and PA-2FE-FX modules utilize Quality of Service (QoS) capabilities to prioritize traffic, ensuring that critical applications receive the necessary bandwidth. This is particularly beneficial for VoIP services, video conferencing, and other latency-sensitive applications. Additionally, the modules offer support for VLANs, allowing organizations to segment their networks effectively and enhance security by isolating sensitive data traffic.

Another important characteristic of these modules is their hot-swappable nature, enabling users to replace them without powering down the router, thus minimizing downtime. This feature is critical for businesses that require high availability and reliability from their networking equipment.

In summary, the Cisco Systems PA-2FE-TX and PA-2FE-FX interface modules stand out for their versatility, enabling businesses to implement customized networking solutions tailored to specific needs. With support for both copper and fiber connections, advanced QoS features, and seamless integration into existing Cisco routers, these modules reinforce Cisco’s commitment to providing innovative, robust network solutions that cater to the demands of modern enterprise environments.
Top Page Image Contents