Cisco Systems PA-2FE-TX, PA-2FE-FX manual Using the show diag Command

Page 74

Chapter 4 Configuring the PA-2FE

Checking the Configuration

Router uptime is 5 minutes

System returned to ROM by reload

System image file is "tftp://172.168.0.0"

cisco RSP4 (R5000) processor with 65536K/2072K bytes of memory. R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache Last reset from power-on

G.703/E1 software, Version 1.0. G.703/JT2 software, Version 1.0.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp). Bridging software.

TN3270 Emulation software. Chassis Interface.

1 EIP controller (6 Ethernet).

1 VIP2 controller (2 FastEthernet).

1 VIP2 R5K controller (2 FastEthernet).

6 Ethernet/IEEE 802.3 interface(s)

4 FastEthernet/IEEE 802.3 interface(s)

123K bytes of non-volatile configuration memory.

8192K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 20480K bytes of Flash PCMCIA card at slot 1 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K).

No slave installed in slot 7. Configuration register is 0x100

Using the show diag Command

Display the types of port adapters installed in your system (and specific information about each) using the show diag slot command, where slot is the port adapter slot in a Cisco 7100 series router, Cisco 7200 series router, Cisco 7200 VXR router, Cisco uBR7200 series router, Cisco 7201 router, Cisco 7301 router, or Cisco 7401ASR router, the module slot in a Cisco 7304 PCI Port Adapter Carrier Card in a Cisco 7304 router, and the interface processor slot in a Cisco 7500 series router with a VIP.

Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only.

The following sections provide platform-specific output examples using the show diag command:

•Cisco 7100 Series Routers—Example Output of the show diag Command, page 4-15

•Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Example Output of the show diag Command, page 4-15

•Cisco 7201 Router—Example Output of the show diag Command, page 4-16

•Cisco 7401ASR Routers—Example Output of the show diag Command, page 4-17

•VIP in Cisco 7500 Series Routers—Example Output of the show diag Command, page 4-17

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

4-14

OL-3474-07

 

 

Page 73 Page 75
Image 74
Page 73 Page 75
Contents Americas Headquarters Text Part Number OL-3474-07Cisco Systems, Inc. All rights reserved N T E N T S Adapter Using the ping Command to Verify Network Connectivity OL-3474-07 Document Revision History Document Version Date Change SummaryRelated Documentation ObjectivesOrganization Section Title DescriptionPreface Related Documentation Preface Related Documentation Fast Ethernet Port Adapter Family PA-FE and PA-2FE Datasheet Xii Overview Port Adapter OverviewParameter Ieee 802.3u 100BASE-T SpecificationsFast Ethernet Overview 100BASE-FX MultimodeDTE* DTE LED Label Color State Function LEDsReceptacles, Cables, and Pinouts RJ-45 Port and Connector Pin DescriptionPA-2FE-FX Duplex SC Connector Network ManagementPort Adapter Slot Locations on the Supported Platforms Cisco 7100 Series Routers Slot Numbering11 Port Adapter Slots in the Cisco 7140 Series Router Cisco uBR7200 Series Router Slot Numbering 13 Port Adapter Slots in the Cisco uBR7246VXR RouterCisco 7201 Router Slot Numbering Cisco 7301 Router Slot NumberingCisco 7304 PCI Port Adapter Carrier Card Slot Numbering SlotCisco 7401ASR Router Slot Numbering Cisco 7500 Series Routers with VIP Slot NumberingRSP VIP interface-slot RSP-slot 5 7 9 11 Identifying Interface Addresses Platform Interface Address Format Numbers SyntaxCisco 7120 Router and Cisco 7140 Router Interface Addresses Cisco 7301 Router Interface Addresses Cisco uBR7200 Series Routers Interface AddressesCisco 7201 Router Interface Addresses Cisco 7401ASR Router Interface AddressesCisco 7500 Series Routers VIP Interface Addresses OL-3474-07 Preparing for Installation Required Tools and EquipmentPlatform Recommended Minimum Cisco IOS Release Software and Hardware RequirementsChecking Hardware and Software Compatibility Safety Guidelines Safety WarningsAviso Instruções Importantes DE Segurança Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Guarde Estas Instrucciones GEM Disse Anvisninger Page Electrical Equipment Guidelines Telephone Wiring Guidelines Preventing Electrostatic Discharge DamageFCC Class a Compliance Removing and Installing Port Adapters Handling Port AdaptersOnline Insertion and Removal Handling a Port AdapterRemoving and Installing Port Adapters Port Adapter Removal and Installation Cisco 7100 Series-Removing and Installing a Port Adapter StepRemoval applies to any Cisco uBR7200 Series Routers-Removing a Port Adapter Cisco uBR7200 Series Routers-Installing a Port Adapter Metal carrier PC boardCisco 7201 Router-Removing and Installing a Port Adapter Cisco 7301 Router-Removing and Installing a Port Adapter Page CC-PA Cisco 7401ASR Router-Removing and Installing a Port Adapter Captive installation screw With the screw removed, grasp Connecting a PA-2FE RJ-45 or SC Cable Connecting a PA-2FE-TX RJ-45 Cable-Horizontal OrientationConnecting PA-2FE-FX SC Cables-Horizontal Orientation OL-3474-07 Configuring the PA-2FE Using the Exec Command InterpreterConfiguring the Interfaces Shutting Down an InterfacePlatform Command Example Fastethernet and slot/portAdapter/port Show interfaces fastethernet Slot-number/port-number Performing a Basic Interface Configuration Fastethernet Command Function Example Checking the ConfigurationUsing show Commands to Verify the New Interface Status Command Function Example Using the show version or show hardware Commands Cisco 7201 Router-Example Output of the show version Command Last reset from power-on 1 FastEthernet interface Using the show diag Command Show diag Cisco 7201 Router-Example Output of the show diag Command 0x3060 Using the show interfaces Command Configuring the PA-2FE Checking the Configuration Router# show interfaces Using the ping Command to Verify Network Connectivity Router# pingConfiguring the PA-2FE Checking the Configuration

PA-2FE-FX, PA-2FE-TX specifications

Cisco Systems PA-2FE-TX and PA-2FE-FX are high-performance Ethernet interface modules designed to enhance the capabilities of Cisco 2600 and 3600 series routers. They provide businesses with flexible and reliable networking solutions that meet the increasing demand for bandwidth and connectivity.

One of the main features of the PA-2FE-TX module is its ability to support two 10/100 Mbps Fast Ethernet interfaces. This allows organizations to connect multiple devices while improving network performance. The PA-2FE-FX module, on the other hand, is designed for optical fiber connections. It features two Fast Ethernet interfaces that utilize an SC connector for easier cable management in fiber optic environments. This capability facilitates long-distance data transmission, making it suitable for backbone connections or inter-building links.

Both modules incorporate advanced technologies to ensure efficient data handling. They support Cisco's Auto-Negotiation feature, enabling devices to automatically select the optimal speed and duplex settings, thus simplifying deployment and reducing configuration errors. This functionality is vital in environments with varied device capabilities, allowing seamless communication across the network.

The PA-2FE-TX and PA-2FE-FX modules utilize Quality of Service (QoS) capabilities to prioritize traffic, ensuring that critical applications receive the necessary bandwidth. This is particularly beneficial for VoIP services, video conferencing, and other latency-sensitive applications. Additionally, the modules offer support for VLANs, allowing organizations to segment their networks effectively and enhance security by isolating sensitive data traffic.

Another important characteristic of these modules is their hot-swappable nature, enabling users to replace them without powering down the router, thus minimizing downtime. This feature is critical for businesses that require high availability and reliability from their networking equipment.

In summary, the Cisco Systems PA-2FE-TX and PA-2FE-FX interface modules stand out for their versatility, enabling businesses to implement customized networking solutions tailored to specific needs. With support for both copper and fiber connections, advanced QoS features, and seamless integration into existing Cisco routers, these modules reinforce Cisco’s commitment to providing innovative, robust network solutions that cater to the demands of modern enterprise environments.
Top Page Image Contents