Cisco Systems ONS 15310-CL, ONS 15310-MA manual Alarm List by Logical Object Type, Type Definition

Page 120

Chapter 2 Alarm Troubleshooting

2.4 Alarm List by Logical Object Type

Table 2-7

Alarm Logical Object Type Definitions (continued)

 

 

 

Type

 

Definition

 

 

 

STSTRM

 

STS alarm detection at termination (downstream from the cross-connect).

 

 

 

VCG

 

Virtual concatenation group.

 

 

 

VT-MON

 

VT1 alarm detection at the monitor point (upstream from the cross-connect).

 

 

 

VT-TERM

 

VT1 alarm detection at termination (downstream from the cross-connect).

 

 

 

2.4 Alarm List by Logical Object Type

Table 2-8lists all ONS 15310-CL and ONS 15310-MA Release 7.0 alarms and logical objects as they are given in the system alarm profile. The list entries are organized by logical object name and then by alarm or condition name. Where appropriate, the alarm entries also contain troubleshooting procedures.

Note The list is given here exactly as it is shown in CTC, and in some cases does not follow alphabetical order.

Table 2-8

ONS 15310-CL and ONS 15310-MA Alarm List by Logical Object as Shown in Alarm Profile

 

 

 

 

BITS: AIS (NR)

 

EQPT: SFTWDOWN (MN)

OCN: SSM-STU (NA)

 

 

 

BITS: LOF (MN)

EQPT: SW-MISMATCH (NA)

OCN: STS-SQUELCH-L (NA)

 

 

 

BITS: LOS (MN)

EQPT: SWMTXMOD-PROT (CR)

OCN: SYNC-FREQ (NA)

 

 

 

BITS: SSM-DUS (NA)

EQPT: SWMTXMOD-WORK (CR)

OCN: TIM (CR)

 

 

 

BITS: SSM-FAIL (MN)

EQPT: WKSWPR (NA)

OCN: TIM-MON (MN)

 

 

 

BITS: SSM-OFF (NA)

EQPT: WTR (NA)

OCN: TIM-S (CR)

 

 

 

BITS: SSM-PRS (NA)

EXT-SREF: FRCDSWTOPRI (NA)

OCN: VT-SQUELCH-L (NA)

 

 

 

BITS: SSM-RES (NA)

EXT-SREF: FRCDSWTOSEC (NA)

OCN: WKSWPR (NA)

 

 

 

BITS: SSM-SMC (NA)

EXT-SREF: FRCDSWTOTHIRD (NA)

OCN: WTR (NA)

 

 

 

BITS: SSM-ST2 (NA)

EXT-SREF: MANSWTOPRI (NA)

PPM: AS-CMD (NA)

 

 

 

BITS: SSM-ST3 (NA)

EXT-SREF: MANSWTOSEC (NA)

PPM: AS-MT (NA)

 

 

 

BITS: SSM-ST3E (NA)

EXT-SREF: MANSWTOTHIRD (NA)

PPM: EQPT (CR)

 

 

 

BITS: SSM-ST4 (NA)

EXT-SREF: SWTOPRI (NA)

PPM: HI-LASERBIAS (MN)

 

 

 

BITS: SSM-STU (NA)

EXT-SREF: SWTOSEC (NA)

PPM: HI-LASERTEMP (MN)

 

 

 

BITS: SSM-TNC (NA)

EXT-SREF: SWTOTHIRD (NA)

PPM: HI-TXPOWER (MN)

 

 

 

BITS: SYNC-FREQ (NA)

EXT-SREF: SYNCPRI (MN)

PPM: IMPROPRMVL (CR)

 

 

 

BPLANE: AS-CMD (NA)

EXT-SREF: SYNCSEC (MN)

PPM: LO-LASERBIAS (MN)

 

 

 

BPLANE: INVMACADR (MJ)

EXT-SREF: SYNCTHIRD (MN)

PPM: LO-LASERTEMP (MN)

 

 

 

BPLANE: MFGMEM (CR)

FAN: EQPT-MISS (CR)

PPM: LO-TXPOWER (MN)

 

 

 

CE100T: AS-CMD (NA)

FAN: FAN (CR)

PPM: MEA (CR)

 

 

 

CE100T: AS-MT (NA)

FAN: FANDEGRADE (MJ)

PPM: MFGMEM (CR)

 

 

 

CE100T: CARLOSS (MJ)

FAN: MEA (CR)

PPM: PROV-MISMATCH (MN)

 

 

 

 

Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide, R7.0

2-10

Page 119 Page 121
Image 120
Page 119 Page 121
Contents Cisco ONS 15310-CL Cisco ONS 15310-MA Troubleshooting Guide Copyright 2006-2007 Cisco Systems Inc. All rights reserved N T E N T S IiiFeac Send Code Test the OC-N Controller Card 10.1 Alarm Troubleshooting ViiAUTOSW-AIS ViiiDUP-SHELF-ID2-46 Ehibatvg Clear the Ehibatvg Alarm EXTRA-TRAF-PREEMPT2-56 FE-FRCDWKSWBK-SPAN2-61 Hello Xii129 LOA XiiiLpbkcrs Xiv190 RAI 198 SD XviSwtothird XviiTX-RAI XviiiXix Error Messages G U R E S XxiXxii B L E S XxiiiPower Supply Problems XxivRevision History XxvDocument Objectives AudienceDocument Organization Related DocumentationDocument Conventions BoldfaceXxvii Bewaar Deze Instructies XxviiiWarnung Wichtige Sicherheitshinweise XxixSpara Dessa Anvisningar XxxGEM Disse Anvisninger XxxiXxxii Where to Find Safety and Warning Information Obtaining Optical Networking InformationCisco Optical Networking Product Documentation CD-ROM XxxiiiXxxiv General Troubleshooting Network Troubleshooting Tests Facility LoopbackTerminal Loopback Hairpin CircuitCross-Connect Loopback Perform a Facility Loopback on a Source-Node Port Create the Facility Loopback on the Source-Node PortTest the Facility Loopback Perform a Hairpin on a Source-Node Port Test the Electrical CablingCreate the Hairpin on the Source-Node Port Page Perform a Terminal Loopback on a Destination-Node Port Test the Hairpin CircuitCreate the Terminal Loopback on a Destination-Node Port Page Perform a Hairpin Test on a Destination-Node Port Continue with the Test the Hairpin Circuit procedure on Perform a Facility Loopback on a Destination Port Create a Facility Loopback Circuit on a Destination PortTest the Facility Loopback Circuit Identify Points of Failure on an OC-N Circuit Path Perform a Facility Loopback on a Source-Node OC-N PortCreate the Facility Loopback on the Source OC-N Port Click the Maintenance Optical Loopback Port tabs Perform a Cross-Connect Loopback on the Source OC-N PortCreate the Cross-Connect Loopback on the Source OC-N Port Test the Cross-Connect Loopback CircuitPerform a Terminal Loopback on a Source-Node OC-N Port Create the Terminal Loopback on a Source Node OC-N PortTest the Terminal Loopback Circuit Click the Maintenance Optical Loopback Port tabs Test the Facility Loopback Circuit Test the Terminal Loopback Circuit Perform a Facility Loopback on a Destination-Node OC-N Port Create the Facility Loopback on a Destination-Node OC-N PortTest the Facility Loopback Circuit Perform a Terminal Loopback on a Destination-Node OC-N Port Create the Terminal Loopback on a Destination-Node OC-N PortTest the Terminal Loopback Circuit Feac Send Code Feac Alarms WBE-28/WBE-84 Inhibit Feac LoopbackTroubleshooting Ethernet Circuit Paths With Loopbacks Click the Maintenance Loopback tabs Perform a Facility Loopback on a Source-Node Ethernet PortTest and Clear the Facility Loopback Circuit Cisco ONS 15310-MA Procedure Guide Test the Ethernet CardPerform a Terminal Loopback on a Source-Node Ethernet Port Create the Terminal Loopback on a Source-Node Ethernet PortTest and Clear the Ethernet Terminal Loopback Circuit Test the Ethernet Card Create a Facility Loopback on an Intermediate-Node OC-N Port Test and Clear the OC-N Facility Loopback Circuit Test the OC-N Controller CardPerform a Terminal Loopback on Intermediate-Node OC-N Ports Create a Terminal Loopback on Intermediate-Node OC-N Ports Test and Clear the OC-N Terminal Loopback Circuit Test the OC-N CardCisco ONS 15310-MA Procedure Guide Connect a test set to the CE100T-8 card that you are testing Test and Clear the Ethernet Facility Loopback Circuit Connect a test set to the CE100T-8 port that you are testing Click the Maintenance Loopback tabs Test and Clear the Ethernet Terminal Loopback Circuit Restore the Database and Default Settings PC Connectivity TroubleshootingRestore the Node Database Windows PC System Minimum Requirements 2 Sun, Solaris, or Unix System Minimum RequirementsSupported Platforms, Browsers, and JREs Unable to Verify the IP Configuration of Your Windows PC Verify the IP Configuration of Your Windows PCUnsupported Platforms and Browsers Browser Login Does Not Launch Java Close the Java Plug-in Control Panel windowReconfigure the Browser Unable to Verify the NIC Connection on Your Windows PCReplacement LAN Cables procedure on Verify Windows PC Connection to the Node PingCTC Operation Troubleshooting Unable to Launch CTC Help After Removing NetscapePing the ONS 15310-CL or ONS 15310-MA Set Internet Explorer as the Default Browser for CTC Unable to Change Node View to Network ViewBrowser Stalls When Downloading CTC JAR Files from port ExampleDisable the VirusScan Download Scan Uncheck the Enable Internet download scanning check boxCTC Does Not Launch Redirect the Netscape Cache to a Valid DirectorySluggish CTC Operation or Login Problems Delete the CTC Cache File AutomaticallyDelete the CTC Cache File Manually Deleting the CTC CacheNOT-AUTHENTICATED Node Icon is Gray on CTC Network ViewINCOMPATIBLE-SW Java Runtime Environment Incompatible Launch CTC to Correct the Core Version BuildBuild procedure on Different CTC Releases Do Not Recognize Each OtherUsername or Password Does Not Match the Port Information Superuser Password Needs to Be ResetVerify Correct Username and Password Reset the ONS 15310-CL or ONS 15310-MA Password No IP Connectivity Exists Between NodesPath in Use Error When Creating a Circuit Cancel the Circuit Creation and Start OverDCC Connection Lost Circuits and Timing Calculate and Design IP SubnetsCircuit Transitions to Partial Status Circuits Remain in Partial Status View the State of Circuit NodesAIS-V on Unused 15310-CL-CTX Card VT Circuits Clear AIS-V on Unused Controller Card VT CircuitsClick Circuits Circuit Creation Error with VT1.5 Circuit 10.5 OC-3 and DCC LimitationsONS 15310-CL or ONS 15310-MA Switches Timing Reference Holdover Synchronization AlarmFree-Running Synchronization Mode Blinking Stat LED after Installing a CardDaisy-Chained Bits Not Functioning Bit Errors Appear for a Traffic Card Faulty Fiber-Optic ConnectionsFiber and Cabling Verify Fiber-Optic Connections Crimp Replacement LAN Cables End view of RJ-45 plugPin Color Pair Name Power and LED Tests Power Supply ProblemsPower Consumption for Node and Cards See , Alarm Troubleshooting, for information about specificCTC, click the Maintenance Diagnostic tabs Click Lamp Test Lamp Tests for Card LEDsVerify Card LED Operation Page Alarm Troubleshooting Alarm Index by Default SeverityCritical Alarms CR Major Alarms MJCTENQPT-PB-WORK Eqpt LOM STSMON, Ststrm SQM Ststrm ENCAP-MISMATCH-P Ststrm LOP-P Stsmon SWMTXMOD-PROT EqptMinor Alarms MN CONTBUS-CLK-B Eqpt ISIS-ADJ-FAIL OCN Sftwdown EqptNot Alarmed Conditions Feprlf OCN LOS Bits TIM-P Stsmon HI-LASERBIAS EqptTX-RAI DS3 Frcdswtopri EXT-SREFVCG-DEG VCG Frcdswtopri NE-SREFAlarms and Conditions Indexed By Alphabetical Entry Not Reported NR ConditionsPage Page Alarm Logical Objects Type DefinitionAlarm List by Logical Object Type Type DefinitionNE Sysboot MJ Stsmon AUTOSW-UNEQ NA OCN AS-CMD NA Ststrm RFI-P NR OCN FE-MANWKSWBK-SPAN NA System LogbufrovflAlarm Troubleshooting Alarm List by Logical Object Type Alarm Characteristics Condition CharacteristicsTrouble Notifications SeveritiesAlarm Hierarchy LOSLOF Lowest DS-N AIS if reported for Outgoing DS-N signals RFI-L RFI-P RFI-VSafety Summary Service EffectStates Alarm Procedures 1 AISAIS-L Clear the AIS ConditionAIS-P AIS-VClear the AIS-L Condition Clear the AIS-P Condition5 ALS APC-ENDApsb ApscdfltkClear the Apscincon Alarm Clear the Apscm AlarmApscincon ApscmClear the Apsimp Alarm ApscnmisApsimp Clear the Apsmm Alarm APS-INV-PRIMApsmm Clear the APS-PRIM-SEC-MISM Alarm APS-PRIM-FACAPS-PRIM-SEC-MISM AS-CMDAS-MT Clear the AS-CMD ConditionAS-MT-OOG AUD-LOG-LOSSClear the AS-MT Condition Clear the AUD-LOG-LOSS ConditionAutoreset Clear the Autoreset AlarmAUD-LOG-LOW AutolsroffAUTOSW-AIS AUTOSW-LOP StsmonClear the AUTOSW-AIS Condition Clear the AUTOSW-LOP VT-MON Alarm AUTOSW-LOP VT-MONAUTOSW-PDI Clear the AUTOSW-LOP Stsmon ConditionAUTOSW-SDBER AUTOSW-SFBERClear the AUTOSW-SDBER Condition Clear the AUTOSW-SFBER ConditionClear the AUTOSW-UNEQ VT-MON Alarm AUTOSW-UNEQ StsmonAUTOSW-UNEQ VT-MON BAT-FAILClear the BAT-FAIL Alarm Clear the Bkupmemp AlarmBkupmemp Lear the Carloss CE100T Alarm BlsrosyncCarloss CE100T Alarm Troubleshooting Carloss CE100T Carloss Eqpt Clear the Carloss Eqpt Alarm Click the Provisioning Pluggable Port Modules tabsClear the Comioxc Alarm CldrestartComioxc Clear the Cldrestart ConditionClear the CONTBUS-CLK-A Alarm CONTBUS-CLK-ACONTBUS-CLK-B CONTBUS-DISABLED Clear the CONTBUS-CLK-B AlarmClear the CONTBUS-DISABLED Alarm Clear the CONTBUS-IO-A AlarmCONTBUS-IO-A Clear the CTNEQPT-PBPROT Alarm CTNEQPT-PBPROTClear the CTNEQPT-PBWORK Alarm CTNEQPT-PBWORKClear the Dataflt Alarm Clear the Dbosync AlarmDataflt DbosyncClear the Disconnected Alarm Disconnected49 DS3-MISM Clear the DS3-MISM ConditionClear the DUP-IPADDR Alarm DUP-IPADDRDUP-NODENAME Node view, click the Provisioning Network General tabsClear the DUP-NODENAME Alarm Clear the Ehibatvg AlarmDUP-SHELF-ID EhibatvgClear the Elwbatvg Alarm ENCAP-MISMATCH-PClear the ENCAP-MISMATCH-P Alarm 56 EOCClick the Provisioning Card tabs Clear the EOC Alarm Click the Provisioning Optical Line tabsEOC-L Click the Provisioning Comm Channels Sdcc tabsClear the EOC-L Alarm Clear the Eqpt AlarmEqpt EQPT-MISS ERFI-P-CONNClear the ERFI-P-CONN Condition ERROR-CONFIG ERFI-P-PAYLDERFI-P-SRVR Clear the ERFI-P-PAYLD ConditionClear the ERROR-CONFIG Alarm Clear the Exccol Alarm ETH-LINKLOSSW-MISMATCH ExccolClear the EXT Alarm 67 EXTEXTRA-TRAF-PREEMPT FailtoswFAILTOSW-PATH 71 FANFAN-DEGRADE FE-AIS FE-DS1-MULTLOSClear the FE-AIS Condition Clear the FE-DS1-MULTLOS ConditionFE-DS1-NSA FE-DS1-SAClear the FE-DS1-NSA Condition Clear the FE-DS1-SA ConditionFE-DS1-SNGLLOS FE-DS3-NSAClear the FE-DS1-SNGLLOS Condition Clear the FE-DS3-NSA ConditionFE-DS3-SA FE-EQPT-NSAFE-FRCDWKSWBK-SPAN Clear the FE-DS3-SA ConditionFE-FRCDWKSWPR-SPAN FE-IDLEFE-LOCKOUTOFPR-SPAN Clear the FE-FRCDWKSWBK-SPAN ConditionFE-LOF FE-LOSFE-MANWKSWBK-SPAN Clear the FE-LOF ConditionClear the Feprlf Alarm FE-MANWKSWPR-SPANFeprlf FORCED-REQFORCED-REQ-SPAN FrcdswtointFrcdswtopri Clear the FORCED-REQ-SPAN ConditionFrcdswtosec FrcdswtothirdFrngsync Clear the Frngsync ConditionClear the GFP-CSF Alarm FstsyncFULLPASSTHR-BI GFP-CSFClear the GFP-EX-MISMATCH Alarm Clear the GFP-LFD AlarmGFP-LFD GFP-UP-MISMATCHClear the GFP-UP-MISMATCH Alarm Clear the Hello AlarmHello Click the Provisioning Port Distance Extension tabsClear the Hibatvg Alarm Clear the HI-LASERBIAS AlarmHibatvg HI-LASERBIASClear the HI-LASERTEMP Alarm HI-LASERTEMPClick the Performance Optics PM tabs HI-RXPOWER Clear the HI-RXPOWER AlarmClear the Hitemp Alarm HitempHI-TXPOWER Clear the HI-TXPOWER AlarmHldovrsync Clear the Hldovrsync Alarm Clear the I-HITEMP Alarm Clear the Improprmvl AlarmImproprmvl Click the Provisioning Timing General tabs Clear the INCOMPATIBLE-SEND-PDIP Alarm Clear the INCOMPATIBLE-SW AlarmINC-ISD INCOMPATIBLE-SEND-PDIPInhswpr InhswwkgINTRUSION-PSWD Clear the Inhswpr ConditionClick Clear Security Intrusion Alarm InvmacadrIoscfgcopy ISIS-ADJ-FAILClear the ISIS-ADJ-FAIL Alarm Click Provisioning OSI Routers SetupClick the Provisioning OSI Routers Setup tabs KB-PASSTHR LasereolLCAS-CRC LCAS-RX-FAIL Transmit nodeLCAS-TX-ADD LCAS-TX-DNUClear the LCAS-RX-FAIL Condition Clear the LOA Alarm LKOUTPR-S129 LOA Clear the LKOUTPR-S ConditionClear the LOF Bits Alarm LOCKOUT-REQLOF Bits Clear the LOCKOUT-REQ ConditionClear the LOF DS1 Alarm LOF DS1Click the Provisioning Timing Bits Facilities tabs Click the Provisioning DS1 Line tabsClear the LOF DS3 Alarm LOF DS3LOF EC1 Clear the LOF EC1 Alarm Clear the LOF OCN AlarmLOF OCN LOF StstrmClear the LOF Ststrm Alarm Clear the Logbufrovfl AlarmLOGBUFR90 LogbufrovflClear the LO-LASERBIAS Alarm LO-LASERBIASLO-LASERTEMP Clear the LOM Alarm Clear the LOP-P Alarm141 LOM LOP-PLO-RXPOWER Clear the LOP-V AlarmClear the LO-RXPOWER Alarm LOP-VClear the LOS Bits Alarm LOS BitsClear the LOS DS1 Alarm Click the Maintenance DS1 tabsLOS DS1 Clear the LOS DS3 Alarm LOS DS3Click the Maintenance DS3 tabs LOS EC1Clear the LOS EC1 Alarm LOS FudcClick the Provisioning EC1 Line tabs Clear the LOS Fudc Alarm LOS OCNClear the LOS OCN Alarm LO-TXPOWER Clear the LO-TXPOWER AlarmLpbkcrs Click the Provisioning Optical Optics Thresholds tabsLPBKDS3FEAC LPBKDS3FEAC-CMDClear the Lpbkcrs Condition Clear the LPBKDS3FEAC ConditionLpbkfacility CE100T Lpbkfacility DS1, DS3Clear the Lpbkfacility CE100T Condition 102Lpbkfacility EC1 Lpbkfacility OCNClear the Lpbkfacility DS1, DS3 Condition Clear the Lpbkfacility EC1 ConditionLpkterminal CE100T Lpbkterminal DS1, DS3Clear the Lpbkfacility OCN Condition Clear the Lpbkterminal CE100T ConditionLpbkterminal EC1 Lpbkterminal OCNClear the Lpbkterminal DS1, DS3 Condition Clear the Lpbkterminal EC1 ConditionClear the Lwbatvg Alarm LwbatvgMAN-REQ Clear the Lpbkterminal OCN ConditionManreset ManswtointManswtopri ManswtosecManswtothird MANUAL-REQ-SPANMateclk Clear the MANUAL-REQ-SPAN ConditionClear the Mateclk Alarm Clear the MEA Eqpt AlarmMEA Eqpt 109MEA FAN MEA PPMClick the Provisioning Protection tabs 110NO-CONFIG MEM-GONEMEM-LOW MfgmemNOT-AUTHENTICATED Clear the NO-CONFIG ConditionOOU-TPT 112OPEN-SLOT PDI-PClear the OOT-TPT Condition Clear the OPEN-SLOT ConditionClear the PDI-P Condition 114Clear the PLM-P Alarm PLM-PPLM-V 115Clear the PLM-V Alarm Clear the Protna AlarmPRC-DUPID ProtnaClear the PWR-FAIL-A Alarm PROV-MISMATCHPWR-FAIL-A 117Clear the PWR-FAIL-B Alarm PWR-FAIL-B190 RAI RFI-LRFI-P Clear the RFI-L ConditionClear the RFI-P Condition 119RFI-V RollClear the RFI-V Condition 120ROLL-PEND RprwRUNCFG-SAVENEED Clear the Rprw Condition198 SD 122SD-L Clear the SD DS1, DS3 Condition123 SD-P Clear the SD-L Condition124 SD-V 202 SFClear the SD-P Condition Clear the SD-V ConditionSF-L SF-PClear the SF DS1, DS3 Condition Clear the SF-L ConditionSftwdown SF-VSHELF-COMM-FAIL Clear the SF-P ConditionClear the SNTP-HOST Alarm SNTP-HOSTSquelch SquelchedClear the SQM Alarm 211 SQMSSM-DUS SSM-FAILClear the SSM-FAIL Alarm SSM-OFFSSM-PRS SSM-RESSSM-SMC SSM-ST2SSM-ST3 SSM-ST3ESSM-ST4 SSM-STUSSM-TNC Clear the SSM-STU ConditionClear the SWMTXMOD-PROT Alarm STS-SQUELCH-LSW-MISMATCH SWMTXMOD-PROTClear the SWMTXMOD-WORK Alarm SWMTXMOD-WORKSwtopri SwtosecSwtothird SYNC-FREQSyncpri Clear the Swtothird ConditionClear the Syncpri Alarm Clear the Syncsec AlarmSyncsec Node view, click the Provisioning Timing General tabsSysboot Clear the Syncthird AlarmSyncthird 236 TIMClear the TIM Alarm 138Clear the TIM-P Alarm TIM-MONTIM-P TIM-SClear the TIM-S Alarm Clear the TIM-V AlarmTIM-V Tptfail CE100TClear the Tptfail CE100T Alarm TX-AISTX-LOF Clear the TX-AIS ConditionClear the UNEQ-P Alarm TX-RAIUNEQ-P Clear the TX-RAI ConditionComplete the Delete a Circuit procedure on 143Clear the UNEQ-V Alarm UNEQ-VVCG-DEG 144VCG-DOWN VT-SQUELCH-LClear the VCG-DEG Condition Clear the VCG-DOWN ConditionDS-1 Line Alarms Wkswpr251 WTR Clear the Wkswpr ConditionTypical Card LED Activity During Reset Protection Switching, Lock Initiation, and ClearingTraffic Card LED Activity 147Initiate a 1+1 Protection Port Force Switch Command Initiate a 1+1 Manual Switch Command148 Clear a 1+1 Force or Manual Switch Command Initiate a Lock-On Command149 Initiate a Card or Port Lockout Command Clear a Lock-On or Lockout CommandInitiate an ONS 15310-MA 11 Card Switch Command 150Click the Perform Path Protection span switching field Node view, choose Go to Network View from the View menu151 152 CTC Card Resetting and Switching Soft- or Hard-Reset an Ethernet or Electrical Card in CTCSoft- or Hard-Reset a Controller Card 153Physical Card Reseating and Replacement Remove and Reinsert Reseat a CardPhysically Replace a Card 154Generic Signal and Circuit Procedures Verify the Signal BER Threshold LevelDelete a Circuit Verify or Create Node DCC TerminationsClear an OC-N Port Facility or Terminal Loopback Circuit Clear an OC-N Port XC Loopback CircuitClear a DS-3 or DS-1 Port Loopback Circuit 156Click the Maintenance EC1 Loopback tabs Clear an EC-1 Port LoopbackClear an Ethernet Card Loopback Circuit 157158 Transient Conditions Transients Indexed By Alphabetical EntryLOGIN-FAILURE-LOCKOUT Condition States Trunk Eqpt Escon FC, GE ISC OCN Stsmon VT-MONTransient Conditions ADMIN-SUSPEND-CLR DBBACKUP-FAILDBRESTORE-FAIL AUD-ARCHIVE-FAILLOGIN-FAILURE-LOCKOUT LOGIN-FAILURE-ONALRDYLOGIN-FAILURE-PSWD LOGIN-FAILURE-USERIDRMON-ALARM LOGOUT-IDLE-USERMANWKSWBK-NO-TRFSW MANWKSWPR-NO-TRFSWRMON-RESET USER-LOGINSESSION-TIME-LIMIT SFTWDOWN-FAILWrmrestart Wrmrestart Error Messages EID-0 EID-1Error Warning Message Description Error Warning Message Description Error Warning Message Description Vlan Error Warning Message Description Error Warning Message Description Blsr Error Warning Message Description Error Warning Message Description Error Warning Message Description Error Warning Message Description Error Messages CTC Error Warning Message Description Error Warning Message Description 1LOCKEDON/LOCKEDOUT Error Warning Message Description Error Warning Message Description Error Warning Message Description Error Messages Ospf Error Warning Message Description Error Warning Message Description Ldcc Error Warning Message Description Error Warning Message Description CTC Error Warning Message Description Provisioning Error Warning Message Description Error Warning Message Description Error Warning Message Description Error Warning Message Description Line ExternalOOS-MA,LPBK&MT Error Messages Error Warning Message Description APC Aborted Error Warning Message Description Error Warning Message Description AUTOSW-AIS FE-AIS TL1Apscdfltk APSC-IMP ApscnmisAutosw BslrosyncCarloss BitsIN-45 DBRESTORE-FAIL DCC DisconnectedIN-46 IN-47 IN-48 Intrusion INTRUSION-PSWD JRELasereol IN-49IN-50 PDI IN-51IN-52 SFTWDOWN-FAIL SSMTCP/IP IN-53TIM IN-54Wkswbk Wkswpr WrmrestartIN-55 IN-56
Related manuals
Manual 12 pages 12.34 Kb Manual 292 pages 38.32 Kb

ONS 15310-CL, ONS 15310-MA specifications

Cisco Systems has long been a leader in networking and telecommunications technology, and among its impressive lineup of products, the Cisco ONS 15310 series stands out as an essential solution for optical networking. This series includes models such as the ONS 15310-MA, ONS 15310-CL, and ONS 15310-CA, each designed to meet the diverse needs of service providers and enterprises seeking to enhance their optical transport networks.

The Cisco ONS 15310-MA is an advanced multi-service platform designed for metropolitan area networks. It facilitates the seamless transport of data, voice, and video over optical networks. One of its main features is its ability to support a variety of interfaces, including Ethernet, SONET/SDH, and Wavelength Division Multiplexing (WDM), allowing users to integrate multiple services into a single platform. Additionally, the ONS 15310-MA supports advanced traffic management and Quality of Service (QoS) features to prioritize critical applications and ensure consistent performance.

The ONS 15310-CL variant is tailored for more specific applications, providing enhanced capabilities aimed at delivering carrier-grade services. It features a robust architecture that accommodates high-capacity traffic without compromising reliability. This model emphasizes low power consumption and a compact design, making it suitable for deployment in space-constrained environments. The ONS 15310-CL also supports a wide range of optical interfaces, making it highly flexible for various network configurations.

In terms of technologies, the Cisco ONS 15310 series leverages Optical Transport Network (OTN) capabilities, providing high efficiency and greater bandwidth utilization. OTN technology enables efficient error correction and adds resilience to the network through its built-in protection mechanisms. Furthermore, the series supports seamless integration with existing IP/MPLS networks, creating a cohesive infrastructure as organizations evolve their networking requirements.

One of the defining characteristics of the ONS 15310 series is its focus on scalability. Network operators can start with a modest deployment and gradually expand capacity as demand grows. This adaptability is complemented by Cisco's comprehensive management and monitoring tools, providing operators with real-time insights into network performance and facilitating proactive management.

In conclusion, the Cisco ONS 15310-MA and ONS 15310-CL models represent sophisticated solutions for modern optical networks. With their versatile features, advanced technologies, and robust design, they empower service providers and enterprises to build resilient, high-capacity networks that meet the demands of today’s data-driven world.
Top Page Image Contents