Cisco Systems ONS 15310-MA, ONS 15310-CL manual Hi-Txpower, Hldovrsync, Clear the HI-TXPOWER Alarm

Page 183

Chapter 2 Alarm Troubleshooting

2.7.109 HI-TXPOWER

2.7.109 HI-TXPOWER

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

SONET Logical Objects: EQPT, OCN

DWDM Logical Object: PPM

The Equipment High Transmit Power alarm is an indicator on the OC-N port transmitted optical signal power. HI-TXPOWER occurs when the measured optical power of the transmitted signal exceeds the threshold.

Note For information about this alarm that applies to DWDM objects, refer to the “Alarm Troubleshooting” chapter in the Cisco ONS 15454 DWDM Troubleshooting Guide.

Clear the HI-TXPOWER Alarm

Step 1 In node view, display the card view for the controller card (15310-CL-CTX or CTX2500 card). Step 2 Click the Provisioning > Optical > Optics Thresholds tabs.

Step 3 Decrease (change toward the negative direction) the OPT-HIGH column value by 1%.

Step 4 If the card transmit power setting cannot be lowered without disrupting the signal, complete the “Physically Replace a Card” procedure on page 2-154.

Caution Removing a card that currently carries traffic on one or more ports can cause a traffic hit. To avoid this, perform an external switch if a switch has not already occurred. See the “2.10.1 Protection Switching, Lock Initiation, and Clearing” section on page 2-147for commonly used traffic-switching procedures.

Caution Always use the supplied electrostatic discharge wristband when working with a powered ONS 15310-CL or ONS 15310-MA.

Note When you replace a card with the identical type of card, you do not need to make any changes to the database.

Step 5 If the alarm does not clear, log into the Technical Support Website at http://www.cisco.com/techsupport for more information or call Cisco TAC (1-800-553-2447).

2.7.110 HLDOVRSYNC

Default Severity: Not Alarmed (NA), Non-Service-Affecting (NSA)

SONET Logical Object: NE-SREF

Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide, R7.0

2-73

Page 182 Page 184
Image 183
Page 182 Page 184
Contents Cisco ONS 15310-CL Cisco ONS 15310-MA Troubleshooting Guide Copyright 2006-2007 Cisco Systems Inc. All rights reserved Iii N T E N T SFeac Send Code Test the OC-N Controller Card 10.1 Vii Alarm TroubleshootingViii AUTOSW-AISDUP-SHELF-ID2-46 Ehibatvg Clear the Ehibatvg Alarm EXTRA-TRAF-PREEMPT2-56 FE-FRCDWKSWBK-SPAN2-61 Xii HelloXiii 129 LOAXiv Lpbkcrs190 RAI Xvi 198 SDXvii SwtothirdXviii TX-RAIXix Error Messages Xxi G U R E SXxii Xxiii B L E SXxiv Power Supply ProblemsXxv Revision HistoryRelated Documentation Document ObjectivesAudience Document OrganizationDocument Conventions BoldfaceXxvii Xxviii Bewaar Deze InstructiesXxix Warnung Wichtige SicherheitshinweiseXxx Spara Dessa AnvisningarXxxi GEM Disse AnvisningerXxxii Xxxiii Where to Find Safety and Warning InformationObtaining Optical Networking Information Cisco Optical Networking Product Documentation CD-ROMXxxiv General Troubleshooting Facility Loopback Network Troubleshooting TestsTerminal Loopback Hairpin CircuitCross-Connect Loopback Create the Facility Loopback on the Source-Node Port Perform a Facility Loopback on a Source-Node PortTest the Facility Loopback Perform a Hairpin on a Source-Node Port Test the Electrical CablingCreate the Hairpin on the Source-Node Port Page Perform a Terminal Loopback on a Destination-Node Port Test the Hairpin CircuitCreate the Terminal Loopback on a Destination-Node Port Page Perform a Hairpin Test on a Destination-Node Port Continue with the Test the Hairpin Circuit procedure on Create a Facility Loopback Circuit on a Destination Port Perform a Facility Loopback on a Destination PortTest the Facility Loopback Circuit Identify Points of Failure on an OC-N Circuit Path Perform a Facility Loopback on a Source-Node OC-N PortCreate the Facility Loopback on the Source OC-N Port Perform a Cross-Connect Loopback on the Source OC-N Port Click the Maintenance Optical Loopback Port tabsTest the Cross-Connect Loopback Circuit Create the Cross-Connect Loopback on the Source OC-N PortCreate the Terminal Loopback on a Source Node OC-N Port Perform a Terminal Loopback on a Source-Node OC-N PortTest the Terminal Loopback Circuit Click the Maintenance Optical Loopback Port tabs Test the Facility Loopback Circuit Test the Terminal Loopback Circuit Create the Facility Loopback on a Destination-Node OC-N Port Perform a Facility Loopback on a Destination-Node OC-N PortTest the Facility Loopback Circuit Create the Terminal Loopback on a Destination-Node OC-N Port Perform a Terminal Loopback on a Destination-Node OC-N PortTest the Terminal Loopback Circuit Feac Send Code WBE-28/WBE-84 Inhibit Feac Loopback Feac AlarmsTroubleshooting Ethernet Circuit Paths With Loopbacks Click the Maintenance Loopback tabs Perform a Facility Loopback on a Source-Node Ethernet PortTest and Clear the Facility Loopback Circuit Test the Ethernet Card Cisco ONS 15310-MA Procedure GuideCreate the Terminal Loopback on a Source-Node Ethernet Port Perform a Terminal Loopback on a Source-Node Ethernet PortTest and Clear the Ethernet Terminal Loopback Circuit Test the Ethernet Card Create a Facility Loopback on an Intermediate-Node OC-N Port Test the OC-N Controller Card Test and Clear the OC-N Facility Loopback CircuitPerform a Terminal Loopback on Intermediate-Node OC-N Ports Create a Terminal Loopback on Intermediate-Node OC-N Ports Test the OC-N Card Test and Clear the OC-N Terminal Loopback CircuitCisco ONS 15310-MA Procedure Guide Connect a test set to the CE100T-8 card that you are testing Test and Clear the Ethernet Facility Loopback Circuit Connect a test set to the CE100T-8 port that you are testing Click the Maintenance Loopback tabs Test and Clear the Ethernet Terminal Loopback Circuit Restore the Database and Default Settings PC Connectivity TroubleshootingRestore the Node Database Windows PC System Minimum Requirements 2 Sun, Solaris, or Unix System Minimum RequirementsSupported Platforms, Browsers, and JREs Unable to Verify the IP Configuration of Your Windows PC Verify the IP Configuration of Your Windows PCUnsupported Platforms and Browsers Close the Java Plug-in Control Panel window Browser Login Does Not Launch JavaUnable to Verify the NIC Connection on Your Windows PC Reconfigure the BrowserVerify Windows PC Connection to the Node Ping Replacement LAN Cables procedure onCTC Operation Troubleshooting Unable to Launch CTC Help After Removing NetscapePing the ONS 15310-CL or ONS 15310-MA Unable to Change Node View to Network View Set Internet Explorer as the Default Browser for CTCExample Browser Stalls When Downloading CTC JAR Files from portRedirect the Netscape Cache to a Valid Directory Disable the VirusScan Download ScanUncheck the Enable Internet download scanning check box CTC Does Not LaunchDelete the CTC Cache File Automatically Sluggish CTC Operation or Login ProblemsDeleting the CTC Cache Delete the CTC Cache File ManuallyNOT-AUTHENTICATED Node Icon is Gray on CTC Network ViewINCOMPATIBLE-SW Launch CTC to Correct the Core Version Build Java Runtime Environment IncompatibleDifferent CTC Releases Do Not Recognize Each Other Build procedure onUsername or Password Does Not Match the Port Information Superuser Password Needs to Be ResetVerify Correct Username and Password No IP Connectivity Exists Between Nodes Reset the ONS 15310-CL or ONS 15310-MA PasswordPath in Use Error When Creating a Circuit Cancel the Circuit Creation and Start OverDCC Connection Lost Circuits and Timing Calculate and Design IP SubnetsCircuit Transitions to Partial Status View the State of Circuit Nodes Circuits Remain in Partial StatusAIS-V on Unused 15310-CL-CTX Card VT Circuits Clear AIS-V on Unused Controller Card VT CircuitsClick Circuits 10.5 OC-3 and DCC Limitations Circuit Creation Error with VT1.5 CircuitHoldover Synchronization Alarm ONS 15310-CL or ONS 15310-MA Switches Timing ReferenceFree-Running Synchronization Mode Blinking Stat LED after Installing a CardDaisy-Chained Bits Not Functioning Bit Errors Appear for a Traffic Card Faulty Fiber-Optic ConnectionsFiber and Cabling Verify Fiber-Optic Connections End view of RJ-45 plug Crimp Replacement LAN CablesPin Color Pair Name Power Supply Problems Power and LED TestsSee , Alarm Troubleshooting, for information about specific Power Consumption for Node and CardsCTC, click the Maintenance Diagnostic tabs Click Lamp Test Lamp Tests for Card LEDsVerify Card LED Operation Page Alarm Index by Default Severity Alarm TroubleshootingENCAP-MISMATCH-P Ststrm LOP-P Stsmon SWMTXMOD-PROT Eqpt Critical Alarms CRMajor Alarms MJ CTENQPT-PB-WORK Eqpt LOM STSMON, Ststrm SQM StstrmCONTBUS-CLK-B Eqpt ISIS-ADJ-FAIL OCN Sftwdown Eqpt Minor Alarms MNFeprlf OCN LOS Bits TIM-P Stsmon HI-LASERBIAS Eqpt Not Alarmed ConditionsFrcdswtopri NE-SREF TX-RAI DS3Frcdswtopri EXT-SREF VCG-DEG VCGNot Reported NR Conditions Alarms and Conditions Indexed By Alphabetical EntryPage Page Type Definition Alarm Logical ObjectsType Definition Alarm List by Logical Object TypeNE Sysboot MJ Stsmon AUTOSW-UNEQ NA OCN FE-MANWKSWBK-SPAN NA System Logbufrovfl OCN AS-CMD NA Ststrm RFI-P NRAlarm Troubleshooting Alarm List by Logical Object Type Severities Alarm CharacteristicsCondition Characteristics Trouble NotificationsAlarm Hierarchy LOSLOF RFI-L RFI-P RFI-V Lowest DS-N AIS if reported for Outgoing DS-N signalsSafety Summary Service EffectStates Clear the AIS Condition Alarm Procedures1 AIS AIS-LClear the AIS-P Condition AIS-PAIS-V Clear the AIS-L ConditionApscdfltk 5 ALSAPC-END ApsbApscm Clear the Apscincon AlarmClear the Apscm Alarm ApscinconClear the Apsimp Alarm ApscnmisApsimp Clear the Apsmm Alarm APS-INV-PRIMApsmm AS-CMD Clear the APS-PRIM-SEC-MISM AlarmAPS-PRIM-FAC APS-PRIM-SEC-MISMClear the AS-CMD Condition AS-MTClear the AUD-LOG-LOSS Condition AS-MT-OOGAUD-LOG-LOSS Clear the AS-MT ConditionAutolsroff AutoresetClear the Autoreset Alarm AUD-LOG-LOWAUTOSW-AIS AUTOSW-LOP StsmonClear the AUTOSW-AIS Condition Clear the AUTOSW-LOP Stsmon Condition Clear the AUTOSW-LOP VT-MON AlarmAUTOSW-LOP VT-MON AUTOSW-PDIClear the AUTOSW-SFBER Condition AUTOSW-SDBERAUTOSW-SFBER Clear the AUTOSW-SDBER ConditionBAT-FAIL Clear the AUTOSW-UNEQ VT-MON AlarmAUTOSW-UNEQ Stsmon AUTOSW-UNEQ VT-MONClear the BAT-FAIL Alarm Clear the Bkupmemp AlarmBkupmemp Lear the Carloss CE100T Alarm BlsrosyncCarloss CE100T Alarm Troubleshooting Carloss CE100T Carloss Eqpt Click the Provisioning Pluggable Port Modules tabs Clear the Carloss Eqpt AlarmClear the Cldrestart Condition Clear the Comioxc AlarmCldrestart ComioxcClear the CONTBUS-CLK-A Alarm CONTBUS-CLK-ACONTBUS-CLK-B Clear the CONTBUS-CLK-B Alarm CONTBUS-DISABLEDClear the CONTBUS-DISABLED Alarm Clear the CONTBUS-IO-A AlarmCONTBUS-IO-A CTNEQPT-PBPROT Clear the CTNEQPT-PBPROT AlarmCTNEQPT-PBWORK Clear the CTNEQPT-PBWORK AlarmDbosync Clear the Dataflt AlarmClear the Dbosync Alarm DatafltClear the DS3-MISM Condition Clear the Disconnected AlarmDisconnected 49 DS3-MISMNode view, click the Provisioning Network General tabs Clear the DUP-IPADDR AlarmDUP-IPADDR DUP-NODENAMEEhibatvg Clear the DUP-NODENAME AlarmClear the Ehibatvg Alarm DUP-SHELF-IDENCAP-MISMATCH-P Clear the Elwbatvg AlarmClear the ENCAP-MISMATCH-P Alarm 56 EOCClick the Provisioning Card tabs Click the Provisioning Optical Line tabs Clear the EOC AlarmClick the Provisioning Comm Channels Sdcc tabs EOC-LClear the EOC-L Alarm Clear the Eqpt AlarmEqpt EQPT-MISS ERFI-P-CONNClear the ERFI-P-CONN Condition Clear the ERFI-P-PAYLD Condition ERROR-CONFIGERFI-P-PAYLD ERFI-P-SRVRClear the ERROR-CONFIG Alarm Exccol Clear the Exccol AlarmETH-LINKLOSS W-MISMATCHFailtosw Clear the EXT Alarm67 EXT EXTRA-TRAF-PREEMPTFAILTOSW-PATH 71 FANFAN-DEGRADE Clear the FE-DS1-MULTLOS Condition FE-AISFE-DS1-MULTLOS Clear the FE-AIS ConditionClear the FE-DS1-SA Condition FE-DS1-NSAFE-DS1-SA Clear the FE-DS1-NSA ConditionClear the FE-DS3-NSA Condition FE-DS1-SNGLLOSFE-DS3-NSA Clear the FE-DS1-SNGLLOS ConditionClear the FE-DS3-SA Condition FE-DS3-SAFE-EQPT-NSA FE-FRCDWKSWBK-SPANClear the FE-FRCDWKSWBK-SPAN Condition FE-FRCDWKSWPR-SPANFE-IDLE FE-LOCKOUTOFPR-SPANClear the FE-LOF Condition FE-LOFFE-LOS FE-MANWKSWBK-SPANFORCED-REQ Clear the Feprlf AlarmFE-MANWKSWPR-SPAN FeprlfClear the FORCED-REQ-SPAN Condition FORCED-REQ-SPANFrcdswtoint FrcdswtopriClear the Frngsync Condition FrcdswtosecFrcdswtothird FrngsyncGFP-CSF Clear the GFP-CSF AlarmFstsync FULLPASSTHR-BIGFP-UP-MISMATCH Clear the GFP-EX-MISMATCH AlarmClear the GFP-LFD Alarm GFP-LFDClick the Provisioning Port Distance Extension tabs Clear the GFP-UP-MISMATCH AlarmClear the Hello Alarm HelloHI-LASERBIAS Clear the Hibatvg AlarmClear the HI-LASERBIAS Alarm HibatvgClear the HI-LASERTEMP Alarm HI-LASERTEMPClick the Performance Optics PM tabs Hitemp HI-RXPOWERClear the HI-RXPOWER Alarm Clear the Hitemp AlarmHI-TXPOWER Clear the HI-TXPOWER AlarmHldovrsync Clear the Hldovrsync Alarm Clear the I-HITEMP Alarm Clear the Improprmvl AlarmImproprmvl Click the Provisioning Timing General tabs INCOMPATIBLE-SEND-PDIP Clear the INCOMPATIBLE-SEND-PDIP AlarmClear the INCOMPATIBLE-SW Alarm INC-ISDClear the Inhswpr Condition InhswprInhswwkg INTRUSION-PSWDISIS-ADJ-FAIL Click Clear Security Intrusion AlarmInvmacadr IoscfgcopyClear the ISIS-ADJ-FAIL Alarm Click Provisioning OSI Routers SetupClick the Provisioning OSI Routers Setup tabs KB-PASSTHR LasereolLCAS-CRC Transmit node LCAS-RX-FAILLCAS-TX-ADD LCAS-TX-DNUClear the LCAS-RX-FAIL Condition Clear the LKOUTPR-S Condition Clear the LOA AlarmLKOUTPR-S 129 LOAClear the LOCKOUT-REQ Condition Clear the LOF Bits AlarmLOCKOUT-REQ LOF BitsClick the Provisioning DS1 Line tabs Clear the LOF DS1 AlarmLOF DS1 Click the Provisioning Timing Bits Facilities tabsClear the LOF DS3 Alarm LOF DS3LOF EC1 LOF Ststrm Clear the LOF EC1 AlarmClear the LOF OCN Alarm LOF OCNLogbufrovfl Clear the LOF Ststrm AlarmClear the Logbufrovfl Alarm LOGBUFR90Clear the LO-LASERBIAS Alarm LO-LASERBIASLO-LASERTEMP LOP-P Clear the LOM AlarmClear the LOP-P Alarm 141 LOMLOP-V LO-RXPOWERClear the LOP-V Alarm Clear the LO-RXPOWER AlarmLOS Bits Clear the LOS Bits AlarmClear the LOS DS1 Alarm Click the Maintenance DS1 tabsLOS DS1 LOS DS3 Clear the LOS DS3 AlarmLOS EC1 Click the Maintenance DS3 tabsClear the LOS EC1 Alarm LOS FudcClick the Provisioning EC1 Line tabs LOS OCN Clear the LOS Fudc AlarmClear the LOS OCN Alarm Click the Provisioning Optical Optics Thresholds tabs LO-TXPOWERClear the LO-TXPOWER Alarm LpbkcrsClear the LPBKDS3FEAC Condition LPBKDS3FEACLPBKDS3FEAC-CMD Clear the Lpbkcrs Condition102 Lpbkfacility CE100TLpbkfacility DS1, DS3 Clear the Lpbkfacility CE100T ConditionClear the Lpbkfacility EC1 Condition Lpbkfacility EC1Lpbkfacility OCN Clear the Lpbkfacility DS1, DS3 ConditionClear the Lpbkterminal CE100T Condition Lpkterminal CE100TLpbkterminal DS1, DS3 Clear the Lpbkfacility OCN ConditionClear the Lpbkterminal EC1 Condition Lpbkterminal EC1Lpbkterminal OCN Clear the Lpbkterminal DS1, DS3 ConditionClear the Lpbkterminal OCN Condition Clear the Lwbatvg AlarmLwbatvg MAN-REQManswtosec ManresetManswtoint ManswtopriClear the MANUAL-REQ-SPAN Condition ManswtothirdMANUAL-REQ-SPAN Mateclk109 Clear the Mateclk AlarmClear the MEA Eqpt Alarm MEA Eqpt110 MEA FANMEA PPM Click the Provisioning Protection tabsMfgmem NO-CONFIGMEM-GONE MEM-LOW112 NOT-AUTHENTICATEDClear the NO-CONFIG Condition OOU-TPTClear the OPEN-SLOT Condition OPEN-SLOTPDI-P Clear the OOT-TPT Condition114 Clear the PDI-P Condition115 Clear the PLM-P AlarmPLM-P PLM-VProtna Clear the PLM-V AlarmClear the Protna Alarm PRC-DUPID117 Clear the PWR-FAIL-A AlarmPROV-MISMATCH PWR-FAIL-ARFI-L Clear the PWR-FAIL-B AlarmPWR-FAIL-B 190 RAI119 RFI-PClear the RFI-L Condition Clear the RFI-P Condition120 RFI-VRoll Clear the RFI-V ConditionClear the Rprw Condition ROLL-PENDRprw RUNCFG-SAVENEED122 198 SDSD-L Clear the SD DS1, DS3 Condition123 SD-P Clear the SD-L Condition124 Clear the SD-V Condition SD-V202 SF Clear the SD-P ConditionClear the SF-L Condition SF-LSF-P Clear the SF DS1, DS3 ConditionClear the SF-P Condition SftwdownSF-V SHELF-COMM-FAILSquelched Clear the SNTP-HOST AlarmSNTP-HOST SquelchSSM-FAIL Clear the SQM Alarm211 SQM SSM-DUSSSM-RES Clear the SSM-FAIL AlarmSSM-OFF SSM-PRSSSM-ST3E SSM-SMCSSM-ST2 SSM-ST3Clear the SSM-STU Condition SSM-ST4SSM-STU SSM-TNCSWMTXMOD-PROT Clear the SWMTXMOD-PROT AlarmSTS-SQUELCH-L SW-MISMATCHSwtosec Clear the SWMTXMOD-WORK AlarmSWMTXMOD-WORK SwtopriClear the Swtothird Condition SwtothirdSYNC-FREQ SyncpriNode view, click the Provisioning Timing General tabs Clear the Syncpri AlarmClear the Syncsec Alarm Syncsec236 TIM SysbootClear the Syncthird Alarm Syncthird138 Clear the TIM AlarmTIM-S Clear the TIM-P AlarmTIM-MON TIM-PTptfail CE100T Clear the TIM-S AlarmClear the TIM-V Alarm TIM-VClear the TX-AIS Condition Clear the Tptfail CE100T AlarmTX-AIS TX-LOFClear the TX-RAI Condition Clear the UNEQ-P AlarmTX-RAI UNEQ-P143 Complete the Delete a Circuit procedure on144 Clear the UNEQ-V AlarmUNEQ-V VCG-DEGClear the VCG-DOWN Condition VCG-DOWNVT-SQUELCH-L Clear the VCG-DEG ConditionClear the Wkswpr Condition DS-1 Line AlarmsWkswpr 251 WTR147 Typical Card LED Activity During ResetProtection Switching, Lock Initiation, and Clearing Traffic Card LED ActivityInitiate a 1+1 Protection Port Force Switch Command Initiate a 1+1 Manual Switch Command148 Clear a 1+1 Force or Manual Switch Command Initiate a Lock-On Command149 150 Initiate a Card or Port Lockout CommandClear a Lock-On or Lockout Command Initiate an ONS 15310-MA 11 Card Switch CommandClick the Perform Path Protection span switching field Node view, choose Go to Network View from the View menu151 152 153 CTC Card Resetting and SwitchingSoft- or Hard-Reset an Ethernet or Electrical Card in CTC Soft- or Hard-Reset a Controller Card154 Physical Card Reseating and ReplacementRemove and Reinsert Reseat a Card Physically Replace a CardVerify or Create Node DCC Terminations Generic Signal and Circuit ProceduresVerify the Signal BER Threshold Level Delete a Circuit156 Clear an OC-N Port Facility or Terminal Loopback CircuitClear an OC-N Port XC Loopback Circuit Clear a DS-3 or DS-1 Port Loopback Circuit157 Click the Maintenance EC1 Loopback tabsClear an EC-1 Port Loopback Clear an Ethernet Card Loopback Circuit158 Transients Indexed By Alphabetical Entry Transient ConditionsLOGIN-FAILURE-LOCKOUT Trunk Eqpt Escon FC, GE ISC OCN Stsmon VT-MON Condition StatesTransient Conditions AUD-ARCHIVE-FAIL ADMIN-SUSPEND-CLRDBBACKUP-FAIL DBRESTORE-FAILLOGIN-FAILURE-USERID LOGIN-FAILURE-LOCKOUTLOGIN-FAILURE-ONALRDY LOGIN-FAILURE-PSWDMANWKSWPR-NO-TRFSW RMON-ALARMLOGOUT-IDLE-USER MANWKSWBK-NO-TRFSWSFTWDOWN-FAIL RMON-RESETUSER-LOGIN SESSION-TIME-LIMITWrmrestart Wrmrestart Error Messages EID-1 EID-0Error Warning Message Description Error Warning Message Description Error Warning Message Description Vlan Error Warning Message Description Error Warning Message Description Blsr Error Warning Message Description Error Warning Message Description Error Warning Message Description Error Warning Message Description Error Messages CTC Error Warning Message Description Error Warning Message Description 1LOCKEDON/LOCKEDOUT Error Warning Message Description Error Warning Message Description Error Warning Message Description Error Messages Ospf Error Warning Message Description Error Warning Message Description Ldcc Error Warning Message Description Error Warning Message Description CTC Error Warning Message Description Provisioning Error Warning Message Description Error Warning Message Description Error Warning Message Description Error Warning Message Description External LineOOS-MA,LPBK&MT Error Messages Error Warning Message Description APC Aborted Error Warning Message Description Error Warning Message Description Apscnmis AUTOSW-AIS FE-AISTL1 Apscdfltk APSC-IMPBits AutoswBslrosync CarlossIN-45 DBRESTORE-FAIL DCC DisconnectedIN-46 IN-47 IN-48 IN-49 Intrusion INTRUSION-PSWDJRE LasereolIN-50 IN-51 PDIIN-52 IN-53 SFTWDOWN-FAILSSM TCP/IPIN-54 TIMWkswbk Wkswpr WrmrestartIN-55 IN-56
Related manuals
Manual 12 pages 12.34 Kb Manual 292 pages 38.32 Kb

ONS 15310-CL, ONS 15310-MA specifications

Cisco Systems has long been a leader in networking and telecommunications technology, and among its impressive lineup of products, the Cisco ONS 15310 series stands out as an essential solution for optical networking. This series includes models such as the ONS 15310-MA, ONS 15310-CL, and ONS 15310-CA, each designed to meet the diverse needs of service providers and enterprises seeking to enhance their optical transport networks.

The Cisco ONS 15310-MA is an advanced multi-service platform designed for metropolitan area networks. It facilitates the seamless transport of data, voice, and video over optical networks. One of its main features is its ability to support a variety of interfaces, including Ethernet, SONET/SDH, and Wavelength Division Multiplexing (WDM), allowing users to integrate multiple services into a single platform. Additionally, the ONS 15310-MA supports advanced traffic management and Quality of Service (QoS) features to prioritize critical applications and ensure consistent performance.

The ONS 15310-CL variant is tailored for more specific applications, providing enhanced capabilities aimed at delivering carrier-grade services. It features a robust architecture that accommodates high-capacity traffic without compromising reliability. This model emphasizes low power consumption and a compact design, making it suitable for deployment in space-constrained environments. The ONS 15310-CL also supports a wide range of optical interfaces, making it highly flexible for various network configurations.

In terms of technologies, the Cisco ONS 15310 series leverages Optical Transport Network (OTN) capabilities, providing high efficiency and greater bandwidth utilization. OTN technology enables efficient error correction and adds resilience to the network through its built-in protection mechanisms. Furthermore, the series supports seamless integration with existing IP/MPLS networks, creating a cohesive infrastructure as organizations evolve their networking requirements.

One of the defining characteristics of the ONS 15310 series is its focus on scalability. Network operators can start with a modest deployment and gradually expand capacity as demand grows. This adaptability is complemented by Cisco's comprehensive management and monitoring tools, providing operators with real-time insights into network performance and facilitating proactive management.

In conclusion, the Cisco ONS 15310-MA and ONS 15310-CL models represent sophisticated solutions for modern optical networks. With their versatile features, advanced technologies, and robust design, they empower service providers and enterprises to build resilient, high-capacity networks that meet the demands of today’s data-driven world.
Top Page Image Contents