Clear the PDI-P Condition, 114 | Cisco Systems ONS 15310-CL guide

Chapter 2 Alarm Troubleshooting

2.7.182 PDI-P

APDI-P condition reported on an OC-3 or OC-12 port supporting an ONS 15310-CL or ONS 15310-MA Ethernet card circuit could result from the end-to-end Ethernet link integrity feature of the Ethernet card. If the link integrity is the cause of the path defect, it is typically accompanied by the “CARLOSS (EQPT)” alarm on page 2-35reported against one or both Ethernet ports terminating the circuit. If this is the case, clear the TPTFAIL and CARLOSS alarms to resolve the PDI-P condition.

Warning Invisible laser radiation could be emitted from the end of the unterminated fiber cable or connector. Do not stare into the beam directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm could pose an eye hazard. Statement 1056

Warning Use of controls, adjustments, or performing procedures other than those specified could result in hazardous radiation exposure. Statement 1057

Clear the PDI-P Condition

Step 1 Verify that all circuits terminating in the reporting card are in an active state by completing the following steps:

a.Click the Circuits tab.

b.Verify that the Status column lists the port as active.

c.If the Status column lists the port as incomplete, wait 10 minutes for the ONS 15310-CL or

ONS 15310-MA to initialize fully. If the incomplete state does not change after full initialization, log into the Technical Support Website at http://www.cisco.com/techsupport for more information or call Cisco TAC to report a Service-Affecting (SA) problem (1-800-553-2447).

Step 2 After determining that the port is active, ensure that the signal source to the card reporting the alarm is working.

Step 3 If traffic is affected, complete the “Delete a Circuit” procedure on page 2-155.

Caution Deleting a circuit can affect existing traffic.

Step 4 Recreate the circuit with the correct circuit size. Refer to the “Create Circuits” chapter in the Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide for procedures.

Step 5 If the circuit deletion and re-creation does not clear the condition, verify that there is no problem with the far-end OC-3 or OC-12 port providing STS payload to the reporting card.

Step 6 If the condition does not clear, confirm that the cross-connect between the OC-3 or OC-12 port and the reporting port is good.

Step 7 If the condition does not clear, clean the far-end optical fiber according to site practice. If no site practice exists, complete the procedure in the “Maintain the Node” chapter in the Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide.

Caution Always use the supplied electrostatic discharge wristband when working with a powered ONS 15310-CL or ONS 15310-MA.

Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide, R7.0

2-114

ONS 15310-CL, ONS 15310-MA specifications

Cisco Systems has long been a leader in networking and telecommunications technology, and among its impressive lineup of products, the Cisco ONS 15310 series stands out as an essential solution for optical networking. This series includes models such as the ONS 15310-MA, ONS 15310-CL, and ONS 15310-CA, each designed to meet the diverse needs of service providers and enterprises seeking to enhance their optical transport networks.

The Cisco ONS 15310-MA is an advanced multi-service platform designed for metropolitan area networks. It facilitates the seamless transport of data, voice, and video over optical networks. One of its main features is its ability to support a variety of interfaces, including Ethernet, SONET/SDH, and Wavelength Division Multiplexing (WDM), allowing users to integrate multiple services into a single platform. Additionally, the ONS 15310-MA supports advanced traffic management and Quality of Service (QoS) features to prioritize critical applications and ensure consistent performance.

The ONS 15310-CL variant is tailored for more specific applications, providing enhanced capabilities aimed at delivering carrier-grade services. It features a robust architecture that accommodates high-capacity traffic without compromising reliability. This model emphasizes low power consumption and a compact design, making it suitable for deployment in space-constrained environments. The ONS 15310-CL also supports a wide range of optical interfaces, making it highly flexible for various network configurations.

In terms of technologies, the Cisco ONS 15310 series leverages Optical Transport Network (OTN) capabilities, providing high efficiency and greater bandwidth utilization. OTN technology enables efficient error correction and adds resilience to the network through its built-in protection mechanisms. Furthermore, the series supports seamless integration with existing IP/MPLS networks, creating a cohesive infrastructure as organizations evolve their networking requirements.

One of the defining characteristics of the ONS 15310 series is its focus on scalability. Network operators can start with a modest deployment and gradually expand capacity as demand grows. This adaptability is complemented by Cisco's comprehensive management and monitoring tools, providing operators with real-time insights into network performance and facilitating proactive management.

In conclusion, the Cisco ONS 15310-MA and ONS 15310-CL models represent sophisticated solutions for modern optical networks. With their versatile features, advanced technologies, and robust design, they empower service providers and enterprises to build resilient, high-capacity networks that meet the demands of today’s data-driven world.