Cisco Systems manual Replacing PA-4T+ Port Adapter Cables, Incorrect, cable upside down

Page 52

Replacing PA-4T+ Port Adapter Cables

Caution Serial interface cables must be attached correctly or damage to the cable plug will result. Attempting to force a cable plug on the 60-pin receptacle can damage the plug. (See Figure 7-2.)

Figure 7-2 Connecting Serial Port Adapter Cables

Correct

Router port

Incorrect, cable upside down

Router port

PA-4T+ in port adapter interface cable

PA-4T+ in port adapter interface cable

H9706

Step 2 Attach the network end of the serial cable to your DSU, CSU, DTE, or other external synchronous serial equipment and tighten the strain-relief screws.

This completes the procedure for attaching serial interface cables to the PA-4T+.

Replacing PA-4T+ Port Adapter Cables

The port adapter cable connected to each port determines the electrical interface type and mode of the port. The default mode of the ports is DCE, which allows you to perform a loopback test on any port without having to attach a port adapter cable. Although DCE is the default, there is no default clock rate set on the interfaces. When there is no cable attached to a port, the software actually identifies the port as Universal (cable unattached) rather than either a DTE or DCE interface.

Following is an example of the show controllers command for Cisco 7100 series, Cisco 7200 series or Cisco uBR7200 series routers that shows an interface port (1/0) that has an EIA/TIA-232 DCE cable attached:

Router# show controllers serial 1/0

M4T: show controller:

PAS unit 8, subunit 0, f/w version 1-25, rev ID 0x2800001, version 2 idb = 0x60B83B40, ds = 0x60B858B8, ssb=0x60B85FFC

Clock mux=0x0, ucmd_ctrl=0x1C, port_status=0x3E Serial config=0x0, line config=0x200 maxdgram=1524, bufpool=48Kb, 96 particles

DCD=up DSR=up DTR=up RTS=up CTS=up line state: up

cable type : V.24 (RS-232) DCE cable, received clockrate 9600 [display text omitted]

Note In the above output from the show controllers command, the PA-4T+ is displayed as M4T.

7-2PA-4T+ Synchronous Serial Port Adapter Installation and Configuration

Image 52
Contents Corporate Headquarters Copyright 1997-1999 Cisco Systems, Inc All rights reserved Overview Port Adapter OverviewPA-4T Port Adapter-Faceplate View Synchronous Serial Overview Router# show diagSerial Interface Specifications Cables and Pinouts PA-4T+ Receptacles and CablesSerial Port Adapter Cables EIA/TIA-232 Connections EIA/TIA-449 Connections PA-4T+ Port Adapter Cable Pinouts EIA-530 ConnectionsRTS/CTS CTS/RTS DSR/DTR DTR/DSR RTS CTS DSR SD+ Shield ground RTS/CTS CTS/RTS DSR/DTR DTR/DSR DCD/LL Rlsd LL/DCD LEDs LEDs on the PA-4T+-Horizontal OrientationLEDs Preface ObjectivesDocument Organization Related DocumentationCisco Connection Online Documentation CD-ROM Preparing for Installation Tools and Parts RequiredSoftware and Hardware Requirements Router Platform Recommended Minimum Cisco IOS ReleaseSoftware and Hardware Requirements Safety Guidelines Safety WarningsTelephone Wiring Guidelines Electrical Equipment GuidelinesFCC Class B Compliance Preventing Electrostatic Discharge DamageFCC Class B Compliance FCC Class B Compliance Installation Overview VIP2 and the PA-4T+ Port AdapterVIP2-15 or VIP2-40 with a PA-4T+ in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Location of Port Adapter Screw-Partial Port Adapter ViewAligning a Port Adapter in a Port Adapter Slot H3152 Cisco 7206 with a PA-4T+ Installed Cisco 7200 Series PA-4T+ Port AdapterPort adapter Handle Lever unlocked Position Handling a Port Adapter Placing the Port Adapter Lever in the Locked Position-Cisco Cisco uBR7200 Series and the PA-4T+ Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Placing the Port Adapter Lever in the Locked Position Installing a Port Adapter Cisco 7100 Series PA-4T+ Port Adapter Cisco 7120 Series Router-Port Adapter Slot 3 LocationCisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides Installing the PA-4T+ Interface Cables Attaching PA-4T+ Port Adapter Interface CablesReplacing PA-4T+ Port Adapter Cables Incorrect, cable upside downFor a VIP2, use the following commands Router# copy running-config startup-config Configuring the PA-4T+ Interfaces Using the Exec Command InterpreterCisco 7200 Series and Cisco uBR7200 Series Ports PA-4T+ Interface Port Address Example-Cisco uBR7246 VIP2 Ports PA-4T+ Interface Port Address Example-CiscoShutting Down an Interface Cisco 7100 Series PortsEnter the shutdown command as follows Router# show interfaces serial 1/0 Performing a Basic Configuration Configure additional interfaces as requiredConfiguring Timing Clock Signals Setting the Clock RateInverting the Clock Signal Inverting the Data Signal Configuring Half-Duplex and Binary Synchronous Communications Configuring Half-Duplex Checking the Configuration Using show Commands to Verify the New Interface StatusConfiguring Bisync Using show Commands to Display Interface Information Hardware is M4T Internet address isChecking the Configuration Router# show version VIP2 show interfaces Command Minute output rate 0 bits/sec, 0 packets/sec System image file is image-name, booted via tftp from Using ping and loopback Commands Checking the Configuration