Cisco Systems PA-4T Performing a Basic Configuration, Configure additional interfaces as required

Page 62

Performing a Basic Configuration

Performing a Basic Configuration

Following are instructions for a basic interface configuration: enabling an interface, specifying IP routing, and setting up external timing on a DCE interface. You might also need to enter other configuration subcommands, depending on the requirements for your system configuration and the protocols you plan to route on the interface. For complete descriptions of configuration subcommands and the configuration options available for serial interfaces, refer to the appropriate software documentation.

In the following procedure, press the Return key after each step unless otherwise noted. At any time you can exit the privileged level and return to the user level by entering disable at the prompt as follows:

Router# disable

Router>

Step 1 At the privileged-level prompt, enter configuration mode and specify that the console terminal will be the source of the configuration subcommands as follows:

Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#

Step 2 For a Cisco 7200 series, Cisco uBR7200 series or a Cisco 7100 series router, specify the first interface to configure by entering the subcommand interface, followed by the type (serial) and slot/interface (port adapter slot number and interface number). The example that follows is for the first interface of the port adapter on a Cisco 7200 series, Cisco 7100 series, or Cisco uBR7200 series router in slot 1:

Router(config)# interface serial 1/0

For a VIP2, specify the first interface to configure by entering the subcommand interface, followed by the type (serial) and slot/port (interface processor slot number/0). The example that follows is for the first interface of the first port adapter on a VIP2 in interface processor slot 3:

Router(config)# interface serial 3/0

Step 3 If IP routing is enabled on the system, you can assign an IP address and subnet mask to the interface with the ip address configuration subcommand, as in the following example:

Router(config-if)#ip address 10.10.10.10 255.255.255.255

Step 4 Add any additional configuration subcommands required to enable routing protocols and set the interface characteristics.

Step 5 If you are configuring a DTE interface, proceed to Step 7. If you are configuring a DCE interface, you need to configure the external clock signal, as described in the next step.

Step 6 Set the clock rate with the clock rate command. (See the next section, “Configuring Timing (Clock) Signals.”)

Router(config-if)# clockrate 7200

Step 7 Change the shutdown state to up and enable the interface as follows:

Router(config-if)# no shutdown

Step 8 Configure additional interfaces as required.

8-8PA-4T+ Synchronous Serial Port Adapter Installation and Configuration

Image 62
Contents Corporate Headquarters Copyright 1997-1999 Cisco Systems, Inc All rights reserved Overview Port Adapter OverviewPA-4T Port Adapter-Faceplate View Synchronous Serial Overview Router# show diagSerial Interface Specifications Cables and Pinouts PA-4T+ Receptacles and CablesSerial Port Adapter Cables EIA/TIA-232 Connections EIA/TIA-449 Connections PA-4T+ Port Adapter Cable Pinouts EIA-530 ConnectionsRTS/CTS CTS/RTS DSR/DTR DTR/DSR RTS CTS DSR SD+ Shield ground RTS/CTS CTS/RTS DSR/DTR DTR/DSR DCD/LL Rlsd LL/DCD LEDs LEDs on the PA-4T+-Horizontal OrientationLEDs Preface ObjectivesDocument Organization Related DocumentationCisco Connection Online Documentation CD-ROM Preparing for Installation Tools and Parts RequiredSoftware and Hardware Requirements Router Platform Recommended Minimum Cisco IOS ReleaseSoftware and Hardware Requirements Safety Guidelines Safety WarningsTelephone Wiring Guidelines Electrical Equipment GuidelinesFCC Class B Compliance Preventing Electrostatic Discharge DamageFCC Class B Compliance FCC Class B Compliance Installation Overview VIP2 and the PA-4T+ Port AdapterVIP2-15 or VIP2-40 with a PA-4T+ in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Location of Port Adapter Screw-Partial Port Adapter ViewAligning a Port Adapter in a Port Adapter Slot H3152 Cisco 7206 with a PA-4T+ Installed Cisco 7200 Series PA-4T+ Port AdapterPort adapter Handle Lever unlocked Position Handling a Port Adapter Placing the Port Adapter Lever in the Locked Position-Cisco Cisco uBR7200 Series and the PA-4T+ Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Placing the Port Adapter Lever in the Locked Position Installing a Port Adapter Cisco 7100 Series PA-4T+ Port Adapter Cisco 7120 Series Router-Port Adapter Slot 3 LocationCisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides Installing the PA-4T+ Interface Cables Attaching PA-4T+ Port Adapter Interface CablesReplacing PA-4T+ Port Adapter Cables Incorrect, cable upside downFor a VIP2, use the following commands Router# copy running-config startup-config Configuring the PA-4T+ Interfaces Using the Exec Command InterpreterCisco 7200 Series and Cisco uBR7200 Series Ports PA-4T+ Interface Port Address Example-Cisco uBR7246 VIP2 Ports PA-4T+ Interface Port Address Example-CiscoShutting Down an Interface Cisco 7100 Series PortsEnter the shutdown command as follows Router# show interfaces serial 1/0 Performing a Basic Configuration Configure additional interfaces as requiredConfiguring Timing Clock Signals Setting the Clock RateInverting the Clock Signal Inverting the Data Signal Configuring Half-Duplex and Binary Synchronous Communications Configuring Half-Duplex Configuring Bisync Using show Commands to Verify the New Interface StatusChecking the Configuration Using show Commands to Display Interface Information Hardware is M4T Internet address isChecking the Configuration Router# show version VIP2 show interfaces Command Minute output rate 0 bits/sec, 0 packets/sec System image file is image-name, booted via tftp from Using ping and loopback Commands Checking the Configuration