Cisco Systems ASR 901 manual Attaching the Cable Guides, Rack-Mounting Brackets section on

Page 34

Chapter 3 Installing the Cisco ASR 901 Mobile Wireless Router

Mounting the Cisco ASR 901 Router

Rack-Mounting Brackets” section on page 3-3.

To mount the Cisco ASR 901 router into the equipment rack, perform the following procedure.

Caution To prevent injury, review the “Safety Guidelines” section on page 2-1and the “Rack-Mounting Configuration Guidelines” section on page 3-2before installing the Cisco ASR 901 router in the equipment rack.

Step 1 Locate the equipment rack position where you plan to install the router.

Step 2 Verify that there are no obstructions and ensure that the equipment rack is stabilized.

Step 3 Position the router in the equipment rack lining up the bracket holes on the router with the holes on the rack and secure with four #6-32 x 0.25-inch mounting screws (two on each side).

Note The vertical spacing for EIA equipment racks is 1.75 inches (4.44 cm), with mounting holes spaced 1.5 inches (3.81 cm) apart.

Step 4 Tighten the screws using a 1/4-inch flat-blade screwdriver (each side).

Attaching the Cable Guides

Complete the following steps to attach the two cable guides to the front of the mounting brackets. This procedure is optional.

Note The cable guides are useful only if your router is front-mounted. Do not attach the cable guides if your router is center-mounted or recess-mounted.

Use the cable guides to dress the cables that attach to the front of the Cisco ASR 901 router. The cable guides allow you to gather the cables and direct them to the left and right sides of the router. This helps to keep the cables from obscuring the fronts of lower routers in the same rack.

Step 1 In the accessory kit, locate the two cable guides (part number 700-01663-01) and two M4.0x20mm Phillips screws used to attach the cable guides (part number 48-0654-01).

Step 2 Position the cable guide over the threaded hole in the front flange of either the left or right mounting bracket. The threaded hole is located midway between the two slotted holes used to mount the unit to the rack.

Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide

3-4

OL-23778-01

 

 

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Cisco Systems, Inc Page Audience Enter a Directory and Determine the Current Directory Time of Day Pinouts OL-23778-01 Document Revision History Revision Date Change SummaryOrganization ObjectivesAudience ConventionsSafety Warnings Related DocumentationOL-23778-01 Introduction Hardware DescriptionCisco ASR 901 Router Front View Cisco ASR 901 Router Ethernet Version Front View Cisco ASR 901 Router-Front ViewCisco ASR 901 Router Rear View Fan Grounding Point LugSpecification Value Power SupplySafety Precautions LEDsPin Connector a RTNPin Connector B Environmental Monitoring Temperature SensorSystem Specifications Description SpecificationRouter Interface Numbering Interface Number Location LabelRegulatory Compliance OL-23778-01 Safety Guidelines Safety with EquipmentSafety with Electricity Preventing Electrostatic Discharge Damage Site Planning Power Supply ConsiderationsPrerequisites Site EnvironmentMethod of Procedure Air Flow GuidelinesUnpacking and Checking the Contents of your Shipment Required Tools and EquipmentInstallation Checklist Task Verified byConsole Port Connections Console Port ConsiderationsCreating a Site Log Task Verified by DatePreparing to Install the Router Console Port Considerations OL-23778-01 Installing the Cisco ASR 901 Mobile Wireless Router Network ModulesRack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 RouterAttaching the Rack-Mounting Brackets Mounting the Cisco ASR 901 Router in a RackAttaching the Cable Guides Rack-Mounting Brackets section onConnecting the Chassis Ground and Power Grounding the Cisco ASR 901 RouterGrounding Point Power Connection Compliance Stripping a Ground WireWiring the DC-Input Power Source 6-Pin Terminal BlockInstalling and Removing SFP Modules Installing SFP ModulesInstalling an SFP Module into an SFP Module Slot Removing SFP ModulesConnecting Cables Connecting the Console PortTypes of RJ-45 Cables Console PortConnecting Gigabit Ethernet Interface Cables Connecting the Network CablesConnecting T1 and E1 Interface Cables Connecting Cables to the Bits Interface Connecting SFP CablesConnecting GPS Cables Connecting to the Management Ethernet Port Powering On the RouterConnecting to Alarm Port Dressing Router CablesFormatting Procedures for Flash Memory Checklist for Power UpPower-On Procedure Interpreting Front-Panel LEDsDisplaying Contents of the Flash Memory File and Directory ProceduresCopying Files Displaying File Content Deleting Files from the Flash MemoryWhat to Do After Installing the Hardware Enter a Directory and Determine the Current DirectoryOL-23778-01 Troubleshooting Problem SolvingEnvironmental Reporting Features Troubleshooting the Power and Cooling SystemsSymptom Possible Cause Corrective Action Troubleshooting Cables, and Connections Information Packet publicationCopper GE from Quad combo PHY ports contain Two Leds each Reading the LEDsChassis LEDs System LEDRJ-45 Ethernet Interface LEDs T1/E1 Interface LEDsSFP Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 portOL-23778-01 Cable Specifications Gigabit Ethernet Connector PinoutsPin FE Signal GE Signal SFP Port Pinouts and Cable SpecificationsT1/E1 Port Pinouts Console Port Signals and Pinouts Console Port Signals and PinoutsPin Signal Name Direction Description Pin Signal Name HP Pins Direction Description RJ-45-to-DB-9 Terminal Adapter ConsoleIdentifying a Rollover Cable Terminal Adapter Device Signal RJ-45 Pin DB-25 PinConsole RJ-45-to-DB-25 Port DTE Time of Day Pinouts Bits Port PinoutsGPS Port Pinouts Management Ethernet Port Pinouts Alarm Port PinoutsPin Signal Name Description 10 MhzRxDP RxDN TxDP Not connected TxDN Site Log Date InitialsNumerics IN-2 IN-3 IN-4

ASR 901 specifications

Cisco Systems ASR 901 is an advanced aggregation services router that is designed to meet the needs of service providers and enterprise networks. It offers a versatile platform suitable for various deployment scenarios ranging from mobile backhaul and broadband aggregation to IP edge routing. The ASR 901 is known for its compact size, energy efficiency, and robust performance, making it a preferred choice for operators looking to enhance their network infrastructure.

One of the main features of the Cisco ASR 901 is its small form factor, which facilitates installation in space-constrained environments. Its design allows for easy deployment in both indoor and outdoor settings, making it ideal for applications such as cell site backhaul and remote locations. The router supports a wide range of interfaces, including Ethernet and T1/E1, providing flexibility in connecting different network types.

The ASR 901 is built on Cisco's IOS XR software, ensuring a highly reliable and secure operating environment. This software is known for its scalability and robustness, providing operators with the ability to support large numbers of subscribers and high traffic volumes. The router also supports system redundancy features, ensuring continuous service availability and minimizing downtime.

In terms of performance, the Cisco ASR 901 delivers high throughput and low latency, which are crucial for delivering quality services like voice, video, and data. With its support for advanced network technologies such as MPLS and IPv6, the ASR 901 can effectively manage complex networking requirements while accommodating future growth.

Security is also a key consideration with the ASR 901. It includes features such as advanced encryption, access control lists, and intrusion prevention systems, aimed at protecting the integrity of network communications. Moreover, its support for Virtual LAN (VLAN) tagging and Quality of Service (QoS) mechanisms allows for efficient traffic management and prioritization, ensuring that critical applications receive the necessary bandwidth.

Furthermore, Cisco provides comprehensive management tools for the ASR 901, allowing network administrators to easily monitor and configure the router. Features like SNMP and NetFlow enable operators to gain insights into network performance and usage patterns, facilitating proactive management of their environments.

Overall, the Cisco Systems ASR 901 stands out as a powerful and flexible router, designed to meet the evolving demands of modern networks. Its combination of compact design, scalability, and advanced features positions it as an ideal solution for service providers and enterprises seeking reliable and efficient network solutions.
Top Page Image Contents