Cisco Systems ASR 1000 manual Making Changes to Individual Controller Settings Example

Page 37

Chapter 2 Configuring Integrated Session Border Controller

Configuration Examples

Making Changes to Individual Controller Settings: Example

You want to change an individual setting configured on a controller and that controller is already configured. Individual controller-specific settings include any one of the following:

remote address

remote port

transport type

Note You cannot change an individual controller setting (remote address, remote port, or transport type) unless you detach the controller first.

To change the remote address, remote port, or transport type setting on a controller, we recommend the following steps:

1.Deactivate the DBE with the no activate command.

2.Enter into VDBE configuration mode with the vdbe command.

3.Detach the controller with the no attach-controllerscommand.

4.Enter into Controller H.248 configuration mode with the controller h248 command.

5.Make the change to the remote address, remote port, or transport type.

6.Exit the Controller H.248 configuration mode with the exit command.

7.Re-attach the controller with the attach-controllerscommand.

8.Exit the VDBE configuration mode with the exit command.

9.Reactivate the DBE with the activate command.

The following example shows the initial configuration:

sbc mySbc dbe

vdbe global use-any-local-port

control-address h248 ipv4 172.25.2.26 controller h248 1

remote-address ipv4 172.25.2.243 attach-controllers

activate location-id 1

media-address ipv4 20.20.20.20 media-address ipv4 21.21.21.21

The following example illustrates a user trying to change the remote address and receiving an error message:

Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)# sbc mySbc dbe

Router(config-sbc-dbe)# vdbe

Router(config-sbc-dbe-vdbe)# controller h248 1

Router(config-sbc-dbe-vdbe-h248)#remote-address ipv4 210.229.108.253

SBC: remote-address cannot be changed while controllers are attached.

Cisco IOS XE Integrated Session Border Controller Configuration Guide for the Cisco ASR 1000 Series Aggregation Services Routers

 

OL-15421-01

2-13

 

 

 

Image 37
Contents Americas Headquarters Page Iii N T E N T SQoS Bandwidth Allocation Traffic Management Package Support Local Source Properties Address and Port Vii IPv6 SupportEvents Storage Until Event Acknowledgment Document Revision History PrefaceObjectives OL-15421-01 May 5 This document was first publishedOrganization Intended AudienceDocument Conventions Related DocumentationCisco ASR 1000 Series Router Documentation Cisco IOS Release 12.2SR Software PublicationsXii Xiii Obtaining Documentation and Submitting a Service RequestXiv Cisco ASR 1000 Series Routers Overview ContentsGeneral Overview Example of SBC High Level Architecture Distributed and Unified ModelsOn page 1-3illustrates the unified model Release Feature Name Related SBC Commands Documented Supported Integrated Session Border Controller FeaturesPackage segment Cisco IOS Cisco IOS Logging Level in ConfiguringNone XE ReleaseMedia-address ipv4 Deployment of the Integrated Session Border Controller Transaction-pending commandIntegrated SBC Used for VoIP Interworking Integrated Session Border Controller DBE Deployment Scenario Prerequisites for Integrated Session Border Controller Configuring Integrated Session Border ControllerRestrictions for Integrated Session Border Controller Summary Steps PrerequisitesEnter your password if prompted Enables privileged Exec modeEnters global configuration mode Enters into interface configuration modeOwn address when connecting to the SBE Configures the DBE to use a specific IPv4 H.248 controlConfigures the H.248 controller for the DBE and enters into Controller H.248 configuration modeWhat To Do Next Troubleshooting TipsExamples Configuring H.248 Logging Level SBC-DBE configuration mode Creates the DBE service on the SBC and enters intoSets a specified logging level to generate detailed logs Messages sent and received. Turns on consoleEnabling H.248 Logging Requests and Responses This section provides the following configuration examples Configuration ExamplesExample H.248 Log Output SBC DBE Configuration Steps Example Making Global Changes to Controllers Example == Make change to local port Following example shows the initial SBC configurationControl-address h248 ipv4 172.25.2.26 controller h248 Making Changes to Individual Controller Settings ExampleIeps Indicator Yes Topology Priority Indicator Yes Emergency IndicatorCisco H.248 Profile Overview of ProfilePackage ID Version Profile PackagesPackage ID Version Support Dependent On Information About Dtmf Interworking Dtmf InterworkingRTP to SIP Interworking Configuring Default Duration of a Dtmf EventSIP to RTP Interworking Configuration mode. Use the sbc-name argument to specify Enters the mode of a DBE service and enters into SBC-DBEName of the DBE service Configures the default duration of a Dtmf eventPage Media Address Pools Restrictions for Configuring Media Address PoolsPrerequisites for Implementing Media Address Pools Information About Media Address Pools Configuring Media Address PoolsEnters into SBC-DBE configuration mode Is configuredConfiguration mode Creates a port range for the configured mediaConfiguring Media Address Pools Example Traffic Management Package Support Quality of Service and Bandwidth ManagementPage Dscp Re-Markings Dscp Marking and IP Precedence MarkingParameters on AC and per SDP on Rtcp Policing Not Using Tman Package Rtcp Policing Using Tman PackageQoS Bandwidth Allocation Rtcp PolicingEnabling Two-Rate Three-Color Policing and Marking Two-Rate Three-Color Policing and MarkingImplementing Two-Rate Three-Color Policing and Marking DBE Restrictions Related Commands Page Enabling Optional H.248 Packages Packages-Signaling and ControlSegmentation Package Support Address Reporting PackageSession Failure Reaction Package Termination State Control Package Tsc-quiesce FeatureTsc-suspend Feature Vlan Package Syntax-Level Support 248.1v3 SupportMGC-Controlled Gateway-Wide Properties Page Services-Signaling and Control DBE Signaling Pinhole Support Extension to H.248 Termination Wildcarding Support Extension to H.248 Audit SupportFlexible Address Prefix Provisioning Locally Hairpinned Sessions Local Source Properties Address and PortTwice Napt Pinhole Hairpinning No Napt Pinhole HairpinningMGC-Specified Local Addresses or Ports Nine-Tier Termination Name Hierarchy Multi-Stream TerminationsRestrictions for Nine-Tier Termination Name Hierarchy Displaying the Nine-Tier Termination Name Hierarchy Information About Nine-Tier Termination Name HierarchyAbc/voice/gn/0/1/0/1/ac/3 Displaying the Nine-Tier Termination Name Hierarchy ExampleOptional Local and Remote Descriptors Remote Source Address Mask Filtering ServiceChange Notification for Interface Status ChangeRTP Specific Behavior Support Sbc interface-id value End Configuration Example Output Tsc-Delay Timer MAX TimerTmax-timercommand configures the value of the T-MAX timer Video on Demand VOD SupportServices-Signaling and Control Video on Demand VOD Support Services-Signaling and Control Video on Demand VOD Support Integrated Session Border Controller Security Firewall Media Pinhole Control Latch and Relatch Support Interim Authentication Header SupportLocal Source Properties Address and Port Etsi TS 102 333 version 1.1.2 Gate Management Package Napt and NAT TraversalTraffic Management Policing Topology HidingTopology Hiding IPv6 Inter-Subscriber Blocking IPv4 Twice NaptRouter# show run interface gigabitEthernet 0/1.1101 QoS Policy-Map-Based Inter-Subscriber Blocking MethodRouter# show class-map IPv6intersubscriber ACL-Based Inter-Subscriber Blocking Method IPv6 SupportIPv6 No Napt Support for Media Flows IPv6 PinholesSend Recv IPv6 Single Napt for SignalingSingle Napt Signaling Flow No Napt Pinholes Topology Hiding No Napt Pinholes Integrated Session Border Controller High Availability High Availability Support10-1 Software Redundancy Hardware RedundancyRoute Processor Redundancy RPR 10-2Issu Support SSO Support10-3 High Availability Support Issu Support 10-411-1 Quality Monitoring and Statistics GatheringBilling and Call Detail Records Congestion-threshold CommandDBE Status Notification Enhanced Event Notification and Auditing11-3 Retention and Returning of H.248 Event InformationResetting the Media Timeout Timers Association ResetSilent Gate Deletion 11-4Network Package Quality Alert Event Middlebox Pinhole Timer Expired Event11-5 Related Command Provisioned Inactivity Timer11-6 IN-1 IN-2 IN-3 Policing Asymmetric policing Ipv6 packets Pinhole Pinhole timeoutRTP specific behavior support SBE IN-4IN-5 IN-6