Cisco Systems ASR 1000 manual MGC-Specified Local Addresses or Ports

Page 70

Chapter 7 H.248 Services—Signaling and Control

MGC-Specified Local Addresses or Ports

•Each “internal termination” has local and remote addresses that are identical to those of the external termination on the associated pinhole.

Note The two terminations between which media loops back are called the “internal terminations” of their respective pinholes. Only external terminations directly receive packets from the network.

•Any remote source address masks (rsams) are duplicated. For example, if a termination with remote address A in one pinhole has an rsam of 1111:2222:3333:4444::/48, then the termination with remote address A in the other pinhole also has an rsam of 1111:2222:3333:4444::/48.

DBE Restrictions

The following are DBE restrictions for the Locally Hairpinned Sessions feature:

•For No NAPT pinholes, the DBE chooses the internal terminations as follows:

–The first specified termination is chosen to be internal.

–The other termination is chosen accordingly from the other pinhole. If the termination with remote address A on one pinhole is internal, then the termination with local address A on the other pinhole is also internal.

–The DBE does not support choosing internal terminations based on termination names.

•For No NAPT hairpins, any Network Address Translation (NAT) latching requests are duplicated. For example, if a termination with remote address A in one pinhole requests NAT latching, then the termination with remote address A in the other pinhole must also request NAT latching. The “request NAT latching” can be done using the ipnapt/latch H.248 signal.

•A hairpin in which both external terminations are provisioned with the NAT latching instruction cannot latch and cannot forward media. No NAPT pinholes are not allowed to (re)latch to the remote addresses on both sides.

•IPv6 hairpins are supported on UDP and TCP.

•Single NAPT pinhole hairpins are not supported.

MGC-Specified Local Addresses or Ports

This feature allows a media gateway controller (MGC) to specify a local address or port for media and signaling flows through the DBE. The MGC specifies a specific address or port for terminations in H.248 Add and Modify requests, instead of using the CHOOSE wildcard.

If either address or port is not specified, it is selected by the DBE from one of the DBE-managed address ranges.

The following error messages describe how the functionality has failed:

•Requested address and port do not belong to a range that has been configured on the DBE with the appropriate class of service for the flow. Megaco error 421 “Unknown action or illegal combination of actions.”

•Media port number requested is an odd number. Megaco error 500 “Internal Software Failure.”

•Request attempted to change the local address and port for an existing flow. Megaco error 501 “Not Implemented.”

Cisco IOS XE Integrated Session Border Controller Configuration Guide for the Cisco ASR 1000 Series Aggregation Services Routers

7-6

OL-15421-01

 

 

Page 69 Page 71
Image 70
Page 69 Page 71
Contents Americas Headquarters Page N T E N T S IiiQoS Bandwidth Allocation Traffic Management Package Support Local Source Properties Address and Port IPv6 Support ViiEvents Storage Until Event Acknowledgment Objectives PrefaceDocument Revision History OL-15421-01 May 5 This document was first publishedIntended Audience OrganizationCisco ASR 1000 Series Router Documentation Related DocumentationDocument Conventions Cisco IOS Release 12.2SR Software PublicationsXii Obtaining Documentation and Submitting a Service Request XiiiXiv Cisco ASR 1000 Series Routers Overview ContentsGeneral Overview Distributed and Unified Models Example of SBC High Level ArchitectureOn page 1-3illustrates the unified model Supported Integrated Session Border Controller Features Release Feature Name Related SBC Commands DocumentedPackage segment None Cisco IOS Logging Level in ConfiguringCisco IOS XE ReleaseMedia-address ipv4 Transaction-pending command Deployment of the Integrated Session Border ControllerIntegrated SBC Used for VoIP Interworking Integrated Session Border Controller DBE Deployment Scenario Prerequisites for Integrated Session Border Controller Configuring Integrated Session Border ControllerRestrictions for Integrated Session Border Controller Prerequisites Summary StepsEnters global configuration mode Enables privileged Exec modeEnter your password if prompted Enters into interface configuration modeConfigures the H.248 controller for the DBE and enters into Configures the DBE to use a specific IPv4 H.248 controlOwn address when connecting to the SBE Controller H.248 configuration modeWhat To Do Next Troubleshooting TipsExamples Configuring H.248 Logging Level Sets a specified logging level to generate detailed logs Creates the DBE service on the SBC and enters intoSBC-DBE configuration mode Messages sent and received. Turns on consoleEnabling H.248 Logging Requests and Responses This section provides the following configuration examples Configuration ExamplesExample H.248 Log Output SBC DBE Configuration Steps Example Making Global Changes to Controllers Example Following example shows the initial SBC configuration == Make change to local portMaking Changes to Individual Controller Settings Example Control-address h248 ipv4 172.25.2.26 controller h248Cisco H.248 Profile Topology Priority Indicator Yes Emergency IndicatorIeps Indicator Yes Overview of ProfileProfile Packages Package ID VersionPackage ID Version Support Dependent On Dtmf Interworking Information About Dtmf InterworkingRTP to SIP Interworking Configuring Default Duration of a Dtmf EventSIP to RTP Interworking Name of the DBE service Enters the mode of a DBE service and enters into SBC-DBEConfiguration mode. Use the sbc-name argument to specify Configures the default duration of a Dtmf eventPage Media Address Pools Restrictions for Configuring Media Address PoolsPrerequisites for Implementing Media Address Pools Configuring Media Address Pools Information About Media Address PoolsConfiguration mode Is configuredEnters into SBC-DBE configuration mode Creates a port range for the configured mediaConfiguring Media Address Pools Example Quality of Service and Bandwidth Management Traffic Management Package SupportPage Dscp Re-Markings Dscp Marking and IP Precedence MarkingParameters on AC and per SDP on QoS Bandwidth Allocation Rtcp Policing Using Tman PackageRtcp Policing Not Using Tman Package Rtcp PolicingEnabling Two-Rate Three-Color Policing and Marking Two-Rate Three-Color Policing and MarkingImplementing Two-Rate Three-Color Policing and Marking DBE Restrictions Related Commands Page Packages-Signaling and Control Enabling Optional H.248 PackagesAddress Reporting Package Segmentation Package SupportSession Failure Reaction Package Tsc-quiesce Feature Termination State Control PackageTsc-suspend Feature 248.1v3 Support Vlan Package Syntax-Level SupportMGC-Controlled Gateway-Wide Properties Page Services-Signaling and Control DBE Signaling Pinhole Support Extension to H.248 Audit Support Extension to H.248 Termination Wildcarding SupportFlexible Address Prefix Provisioning Twice Napt Pinhole Hairpinning Local Source Properties Address and PortLocally Hairpinned Sessions No Napt Pinhole HairpinningMGC-Specified Local Addresses or Ports Nine-Tier Termination Name Hierarchy Multi-Stream TerminationsRestrictions for Nine-Tier Termination Name Hierarchy Information About Nine-Tier Termination Name Hierarchy Displaying the Nine-Tier Termination Name HierarchyDisplaying the Nine-Tier Termination Name Hierarchy Example Abc/voice/gn/0/1/0/1/ac/3Optional Local and Remote Descriptors Remote Source Address Mask Filtering ServiceChange Notification for Interface Status ChangeRTP Specific Behavior Support Sbc interface-id value End Configuration Example Output Tmax-timercommand configures the value of the T-MAX timer MAX TimerTsc-Delay Timer Video on Demand VOD SupportServices-Signaling and Control Video on Demand VOD Support Services-Signaling and Control Video on Demand VOD Support Integrated Session Border Controller Security Firewall Media Pinhole Control Interim Authentication Header Support Latch and Relatch SupportLocal Source Properties Address and Port Napt and NAT Traversal Etsi TS 102 333 version 1.1.2 Gate Management PackageTopology Hiding Traffic Management PolicingTopology Hiding IPv4 Twice Napt IPv6 Inter-Subscriber BlockingQoS Policy-Map-Based Inter-Subscriber Blocking Method Router# show run interface gigabitEthernet 0/1.1101Router# show class-map IPv6intersubscriber IPv6 Support ACL-Based Inter-Subscriber Blocking MethodIPv6 Pinholes IPv6 No Napt Support for Media FlowsIPv6 Single Napt for Signaling Send RecvSingle Napt Signaling Flow No Napt Pinholes Topology Hiding No Napt Pinholes Integrated Session Border Controller High Availability High Availability Support10-1 Route Processor Redundancy RPR Hardware RedundancySoftware Redundancy 10-2Issu Support SSO Support10-3 10-4 High Availability Support Issu SupportQuality Monitoring and Statistics Gathering 11-1DBE Status Notification Congestion-threshold CommandBilling and Call Detail Records Enhanced Event Notification and AuditingRetention and Returning of H.248 Event Information 11-3Silent Gate Deletion Association ResetResetting the Media Timeout Timers 11-4Network Package Quality Alert Event Middlebox Pinhole Timer Expired Event11-5 Related Command Provisioned Inactivity Timer11-6 IN-1 IN-2 IN-3 RTP specific behavior support SBE Pinhole Pinhole timeoutPolicing Asymmetric policing Ipv6 packets IN-4IN-5 IN-6
Top Page Image Contents