Cisco Systems ASR1002 quick start Connect the Router to the Network

Page 11

Step 5 Locate the chassis ground connector on the side of your chassis.

Step 6 Insert the two screws through the holes in the grounding lug.

Step 7 Use the Number 2 Phillips screwdriver to carefully tighten the screws until the grounding lug is held firmly to the chassis. Do not overtighten the screws.

Step 8 Connect the opposite end of the grounding wire to the appropriate grounding point at your site to ensure an adequate chassis ground.

This completes the procedure for attaching a chassis ground connection. Go to the “Connect the Router to the Network” section on page 11 for information on attaching cables.

4Connect the Router to the Network

This section provides information about cables and ports and attaching the router to the network.

•Console and Auxiliary Port Cable Connections, page 11

•Management Ethernet Port Cable Connection, page 12

•Connect the Shared Port Adapter Cables, page 13

•Install the Cables Using the Cable-Management Bracket, page 13

Console and Auxiliary Port Cable Connections

This section describes how to attach a cable to the console or auxiliary ports on the Cisco ASR 1002 Router. The Cisco ASR 1002 Router uses RJ-45 ports for both the auxiliary port and console port to attach a modem or console terminal.

The console DCE-mode port connects a console terminal and a DTE-mode auxiliary port connects a modem or other DCE device to your router.

Caution Both the console and the auxiliary ports are asynchronous serial ports; any devices connected to these ports must be capable of asynchronous transmission. (Asynchronous is the most common type of serial device; for example, most modems are asynchronous devices.) To meet Class A emissions requirements on the Cisco ASR 1002 Router, shielded cables must be used for the console and auxiliary port connections.

Step 1 Before connecting a terminal to the console port, configure the terminal to match the router console port as follows: 9600 baud, 8 data bits, no parity, 1 stop bits. See Figure 8 for console and auxiliary port connector location.

Step 2 Connect to the port using the RJ-45-to-DB-9 cable.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Cisco ASR 1002 Router Document Revision History Documentation and ResourcesTools and Parts Prepare for InstallationPrepare for Equipment Shelf or Tabletop Installation Site Preparation and UnpackingAttach the Rack-Mount Brackets-Chassis Front-Mounted Prepare for Rack-Mount InstallationRack-Mount the Router Attach the Rack-Mount Brackets-Chassis Rear-Mounted Four-Post Rack InstallationShows the Cisco ASR 1002 Router in a four-post rack Installing a Cisco ASR 1002 Router in a Two-Post Rack Two-Post Rack InstallationAttach the Cable-Management Bracket Chassis Ground Connection Installation Attaching a Ground Lug to the Chassis Ground Connector Console and Auxiliary Port Cable Connections Connect the Router to the NetworkManagement Ethernet Port Cable Connection Connect the Shared Port Adapter Cables Install the Cables Using the Cable-Management BracketStart the System Connect AC Power to the Cisco ASR 1002 RouterOutput Input FAN Fail Connect DC Power to the Cisco ASR 1002 RouterShows the DC power supply for the Cisco ASR 1002 Router Step Start the Cisco ASR 1002 Router Verifying Power Supply operationColor Power Up State -Behavior Description Color Behavior Description Page Using the Console to Access the CLI Configuring the RouterConfigure Global Parameters Using the Set-up Facility OK? No ip address Tftptimeout Check the Running Configuration Settings Perform Other Configuration Tasks After InstallationSave the Running Configuration to Nvram Replace the Cisco ASR1000-ESP5 or ASR1000-ESP10 Power Off the Cisco ASR 1002 RouterReplace the Shared Port Adapters Removing an AC Power Supply Replace a Power Supply in the Cisco ASR 1002 RouterAC power cord and service loop Removing the DC Power Supply Installing the DC Power Supply Unit USA

ASR1002 specifications

Cisco Systems ASR1002: An Overview of Main Features, Technologies, and Characteristics

The Cisco ASR1002 router is part of the Aggregation Services Router (ASR) series, renowned for its flexibility and robustness in handling a wide variety of enterprise and service provider applications. Designed for high performance and scalability, the ASR1002 delivers advanced routing capabilities while ensuring efficient resource utilization and minimal operational costs.

One of the standout features of the ASR1002 is its modular architecture. The router supports an extensive range of interfaces and services, allowing organizations to tailor the device to their specific networking requirements. With up to 2GB of onboard memory and the ability to support various WAN technologies, the ASR1002 is well-equipped to handle demanding data workloads.

The ASR1002 offers a performance of up to 2 Gbps of throughput, making it suitable for small to mid-sized businesses needing reliable internet access and robust connectivity. It supports Cisco's Advanced IP Services and offers secure and scalable VPN solutions, enabling organizations to connect multiple sites securely and efficiently.

In addition to its high-speed capabilities, the ASR1002 incorporates advanced security features including Integrated Threat Control, which utilizes Cisco's extensive security technologies to safeguard corporate networks from external and internal threats. It also supports firewall services, intrusion prevention, and secure access protocols, ensuring comprehensive security coverage.

The ASR1002 employs advanced routing technologies like multi-protocol label switching (MPLS) and Border Gateway Protocol (BGP), enabling effective traffic management and seamless integration into existing network infrastructures. This versatility makes it an ideal choice for organizations looking to improve network efficiency and effectiveness.

Another critical characteristic of the ASR1002 is its environmental efficiency. The router is designed with power-saving features and optimizes cooling, contributing to reduced energy costs. With its compact form factor, the ASR1002 can be deployed in various environments without taking up significant space.

Overall, the Cisco ASR1002 stands out as a highly capable and adaptable router, blending advanced features, robust performance, and secure networking capabilities. It caters to the evolving needs of modern enterprises, enabling seamless connectivity and enhancing network reliability. Whether for a small business or a larger enterprise branch, the ASR1002 provides an optimized solution for contemporary networking challenges.
Top Page Image Contents