Cisco Systems Troubleshooting and Component Replacement for ASR1002 and Cisco Quantum Flow Processor
Page 29

Power Off the Cisco ASR 1002 Router

This section explains how to shut down the Cisco ASR 1002 Router. It is recommended that before turning off all power to the chassis, you issue the reload command. This insures that the operating system cleans up all the file systems. Once the reload operation is complete, then the Cisco ASR 1000 Series router can be powered off safely.

To remove power from the Cisco ASR 1002 Router, follow this procedure:

Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit.

Step 2 Before you shutdown the router, issue the IOS reload command to halt the system and then wait for ROM Monitor to execute before proceeding to the next step. The following screen shot shows an example of the reload command:

Router#reload

Proceed with reload? [confirm]

*Jun 18 19:38:21.870: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command.

Step 3 Remove any power cables from the Cisco ASR 1002 Router.

a.For AC power supplies, switch the circuit breaker to the off (O) position and unplug the AC power cord from the power outlet.

b.For DC power supplies, place the power switch in the Standby position. Then remove the terminal block plug from the DC power supply.

Note After powering off the router, wait a minimum of 30 seconds before powering it on again.

Replace the Cisco ASR1000-ESP5 or ASR1000-ESP10

This section provides instructions for removing the Cisco ASR1000-ESP5 or ASR1000-ESP10 from the Cisco ASR 1002 Router. The Cisco ESP5 and ESP10 are Cisco Quantum Flow Processors (QFP) for the Cisco ASR 1002 Router. The Cisco ESP5 and ESP10 are individual FRUs and support online insertion and removal operation. Before you begin, make certain the chassis is grounded.

To remove the Cisco ESP5 or ESP10 from the Cisco ASR 1002 Router, follow this procedure:

Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit. Loosen the captive screws on the Cisco ESP5 or ESP10.

Step 2 Using the handles on both sides of the module, with two hands, gently slide the Cisco ESP5 or ESP10 out of the chassis slot.

Note Handle the Cisco ESP5 and ESP10 by the carrier edges only; never touch the printed circuit board components or connector pins.

Step 3 Place the Cisco ESP5 or the ESP10 on an antistatic surface with its printed circuit board components facing upward or in a static shielding bag.

You have completed the procedure for removing the Cisco ESP5 or ESP10.

To install the Cisco ESP5 or ESP10 in the Cisco ASR 1002 Router, follow this procedure:

Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Cisco ASR 1002 Router Document Revision History Documentation and ResourcesPrepare for Equipment Shelf or Tabletop Installation Prepare for InstallationSite Preparation and Unpacking Tools and PartsAttach the Rack-Mount Brackets-Chassis Front-Mounted Prepare for Rack-Mount InstallationRack-Mount the Router Attach the Rack-Mount Brackets-Chassis Rear-Mounted Four-Post Rack InstallationShows the Cisco ASR 1002 Router in a four-post rack Installing a Cisco ASR 1002 Router in a Two-Post Rack Two-Post Rack InstallationAttach the Cable-Management Bracket Chassis Ground Connection Installation Attaching a Ground Lug to the Chassis Ground Connector Console and Auxiliary Port Cable Connections Connect the Router to the NetworkManagement Ethernet Port Cable Connection Connect the Shared Port Adapter Cables Install the Cables Using the Cable-Management BracketStart the System Connect AC Power to the Cisco ASR 1002 RouterOutput Input FAN Fail Connect DC Power to the Cisco ASR 1002 RouterShows the DC power supply for the Cisco ASR 1002 Router Step Start the Cisco ASR 1002 Router Verifying Power Supply operationColor Power Up State -Behavior Description Color Behavior Description Page Using the Console to Access the CLI Configuring the RouterConfigure Global Parameters Using the Set-up Facility OK? No ip address Tftptimeout Check the Running Configuration Settings Perform Other Configuration Tasks After InstallationSave the Running Configuration to Nvram Replace the Cisco ASR1000-ESP5 or ASR1000-ESP10 Power Off the Cisco ASR 1002 RouterReplace the Shared Port Adapters Removing an AC Power Supply Replace a Power Supply in the Cisco ASR 1002 RouterAC power cord and service loop Removing the DC Power Supply Installing the DC Power Supply Unit USA

ASR1002 specifications

Cisco Systems ASR1002: An Overview of Main Features, Technologies, and Characteristics

The Cisco ASR1002 router is part of the Aggregation Services Router (ASR) series, renowned for its flexibility and robustness in handling a wide variety of enterprise and service provider applications. Designed for high performance and scalability, the ASR1002 delivers advanced routing capabilities while ensuring efficient resource utilization and minimal operational costs.

One of the standout features of the ASR1002 is its modular architecture. The router supports an extensive range of interfaces and services, allowing organizations to tailor the device to their specific networking requirements. With up to 2GB of onboard memory and the ability to support various WAN technologies, the ASR1002 is well-equipped to handle demanding data workloads.

The ASR1002 offers a performance of up to 2 Gbps of throughput, making it suitable for small to mid-sized businesses needing reliable internet access and robust connectivity. It supports Cisco's Advanced IP Services and offers secure and scalable VPN solutions, enabling organizations to connect multiple sites securely and efficiently.

In addition to its high-speed capabilities, the ASR1002 incorporates advanced security features including Integrated Threat Control, which utilizes Cisco's extensive security technologies to safeguard corporate networks from external and internal threats. It also supports firewall services, intrusion prevention, and secure access protocols, ensuring comprehensive security coverage.

The ASR1002 employs advanced routing technologies like multi-protocol label switching (MPLS) and Border Gateway Protocol (BGP), enabling effective traffic management and seamless integration into existing network infrastructures. This versatility makes it an ideal choice for organizations looking to improve network efficiency and effectiveness.

Another critical characteristic of the ASR1002 is its environmental efficiency. The router is designed with power-saving features and optimizes cooling, contributing to reduced energy costs. With its compact form factor, the ASR1002 can be deployed in various environments without taking up significant space.

Overall, the Cisco ASR1002 stands out as a highly capable and adaptable router, blending advanced features, robust performance, and secure networking capabilities. It caters to the evolving needs of modern enterprises, enabling seamless connectivity and enhancing network reliability. Whether for a small business or a larger enterprise branch, the ASR1002 provides an optimized solution for contemporary networking challenges.
Top Page Image Contents