Cisco Systems ASR1002 quick start Attach the Cable-Management Bracket

Page 8

Caution If you are using a two-post rack, secure the rack to the floor surface to prevent tipping and avoid bodily injury and component damage.

Step 1 Position the chassis so the front is closest to you and lift it carefully into the rack. To prevent injury, avoid any sudden twists or moves.

Step 2 Slide the chassis into the rack, pushing it back until the rack-mount brackets meet the mounting strips or posts on both sides of the rack.

Step 3 Position the chassis until the rack-mounting ears are flush against the mounting rails on the rack.

Tip To allow space to attach the cable-management brackets to the chassis in the rack easily, make certain that you use the rack-mount bracket ear holes specified in Step 4.

Step 4 Hold the chassis in position against the mounting rails and follow these steps:

a.The Cisco ASR 1002 Router rack-mount bracket has 4 ear holes and two for the cable-management bracket. Insert the bottom screw into the fifth hole from the top of the rack-mount ear and use a hand-held screwdriver to tighten the screw to the rack rail.

b.Insert the top screw into the second hole from the top of the rack-mount bracket ear hole diagonally from the bottom screw and tighten the screw to the rack rail. See Figure 4.

Step 5 Repeat steps 3 and 4 for the other side of the chassis.

Note As a result of using the specified rack-mount bracket ear holes, the cable-management bracket can be easily attached to the rack-mount bracket after the chassis is in the rack.

This completes the procedure for installing the chassis in a two-post rack. Proceed to the “Attach the Cable-Management Bracket” section on page 8 to continue the installation.

Attach the Cable-Management Bracket

The cable-management bracket mount to each rack-mount bracket on the chassis to provide cable-management to both sides of the chassis.

The cable-management brackets for the Cisco ASR 1002 Router contain one independent cable-management “U” type feature with two screws for each bracket and provides cable dressing of each card module slots. For the ASR 1000 Series SPA interface, these brackets work in tandem with shared port adapter product feature cable-management device to allow installation and removal of adjacent cards without the need to remove cables.

Note Make certain that the cable-management bracket “U” type feature is facing upwards when you attach it to the chassis.

Follow these steps to attach the cable-management brackets to both sides of the Cisco ASR 1002 Router in the rack:

Step 1 Align the cable-management bracket to the rack-mount bracket on one side of the Cisco ASR 1002 Router. The cable-management bracket aligns to the top hole of the chassis rack-mount bracket.

Step 2 Using a Phillips screwdriver, insert one screw through the cable-management bracket and into the chassis rack-mount and tighten the screw.

Note Use the package of four screws that came with your Cisco ASR 1002 Router.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Cisco ASR 1002 Router Documentation and Resources Document Revision HistoryPrepare for Installation Prepare for Equipment Shelf or Tabletop InstallationSite Preparation and Unpacking Tools and PartsAttach the Rack-Mount Brackets-Chassis Front-Mounted Prepare for Rack-Mount InstallationRack-Mount the Router Four-Post Rack Installation Attach the Rack-Mount Brackets-Chassis Rear-MountedShows the Cisco ASR 1002 Router in a four-post rack Two-Post Rack Installation Installing a Cisco ASR 1002 Router in a Two-Post RackAttach the Cable-Management Bracket Chassis Ground Connection Installation Attaching a Ground Lug to the Chassis Ground Connector Connect the Router to the Network Console and Auxiliary Port Cable ConnectionsManagement Ethernet Port Cable Connection Install the Cables Using the Cable-Management Bracket Connect the Shared Port Adapter CablesConnect AC Power to the Cisco ASR 1002 Router Start the SystemConnect DC Power to the Cisco ASR 1002 Router Output Input FAN FailShows the DC power supply for the Cisco ASR 1002 Router Step Verifying Power Supply operation Start the Cisco ASR 1002 RouterColor Power Up State -Behavior Description Color Behavior Description Page Configuring the Router Using the Console to Access the CLIConfigure Global Parameters Using the Set-up Facility OK? No ip address Tftptimeout Check the Running Configuration Settings Perform Other Configuration Tasks After InstallationSave the Running Configuration to Nvram Power Off the Cisco ASR 1002 Router Replace the Cisco ASR1000-ESP5 or ASR1000-ESP10Replace the Shared Port Adapters Replace a Power Supply in the Cisco ASR 1002 Router Removing an AC Power SupplyAC power cord and service loop Removing the DC Power Supply Installing the DC Power Supply Unit USA

ASR1002 specifications

Cisco Systems ASR1002: An Overview of Main Features, Technologies, and Characteristics

The Cisco ASR1002 router is part of the Aggregation Services Router (ASR) series, renowned for its flexibility and robustness in handling a wide variety of enterprise and service provider applications. Designed for high performance and scalability, the ASR1002 delivers advanced routing capabilities while ensuring efficient resource utilization and minimal operational costs.

One of the standout features of the ASR1002 is its modular architecture. The router supports an extensive range of interfaces and services, allowing organizations to tailor the device to their specific networking requirements. With up to 2GB of onboard memory and the ability to support various WAN technologies, the ASR1002 is well-equipped to handle demanding data workloads.

The ASR1002 offers a performance of up to 2 Gbps of throughput, making it suitable for small to mid-sized businesses needing reliable internet access and robust connectivity. It supports Cisco's Advanced IP Services and offers secure and scalable VPN solutions, enabling organizations to connect multiple sites securely and efficiently.

In addition to its high-speed capabilities, the ASR1002 incorporates advanced security features including Integrated Threat Control, which utilizes Cisco's extensive security technologies to safeguard corporate networks from external and internal threats. It also supports firewall services, intrusion prevention, and secure access protocols, ensuring comprehensive security coverage.

The ASR1002 employs advanced routing technologies like multi-protocol label switching (MPLS) and Border Gateway Protocol (BGP), enabling effective traffic management and seamless integration into existing network infrastructures. This versatility makes it an ideal choice for organizations looking to improve network efficiency and effectiveness.

Another critical characteristic of the ASR1002 is its environmental efficiency. The router is designed with power-saving features and optimizes cooling, contributing to reduced energy costs. With its compact form factor, the ASR1002 can be deployed in various environments without taking up significant space.

Overall, the Cisco ASR1002 stands out as a highly capable and adaptable router, blending advanced features, robust performance, and secure networking capabilities. It caters to the evolving needs of modern enterprises, enabling seamless connectivity and enhancing network reliability. Whether for a small business or a larger enterprise branch, the ASR1002 provides an optimized solution for contemporary networking challenges.
Top Page Image Contents