Cisco Systems ASR1002 quick start Installing the DC Power Supply

Page 34

Step 7 Replace the DC power supply within five minutes or the system will shutdown.

You have completed the procedure for removing a DC power supply from the Cisco ASR 1002 Router.

Installing the DC Power Supply

This section provides information about replacing a DC power supply in the Cisco ASR 1002 Router.

Note The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site. Typically, green or green/yellow is used for ground. Make certain the lead color coding you choose for the DC-input power supply matches lead color coding used at the DC power source.

Figure 17 Cisco ASR 1002 Router Terminal Block

1

2

Negative lead

Positive lead

280291

3 Earth ground symbol

Warning

 

Never install an AC power module and a DC power module in the same chassis. Statement 1050

 

 

 

 

Warning

 

Installation of the equipment must comply with local and national electrical codes. Statement 1074

 

 

 

 

 

Step 1

At the rear of the router, check that the power supply Standby switch is in the Standby position.

Step 2

Ensure that the negative and positive leads are disconnected from the site power source and the circuit breaker is turned

 

 

off.

Step 3

 

Insert a DC power supply in power supply slot 0 or power supply slot 1 until it is full seated.

Step 4

 

Using a wire stripper, strip approximately 0.55 inch (14 mm) from the negative, positive, and ground lead.

34

Image 34
Contents Cisco ASR 1002 Router Documentation and Resources Document Revision HistorySite Preparation and Unpacking Prepare for InstallationPrepare for Equipment Shelf or Tabletop Installation Tools and PartsRack-Mount the Router Prepare for Rack-Mount InstallationAttach the Rack-Mount Brackets-Chassis Front-Mounted Four-Post Rack Installation Attach the Rack-Mount Brackets-Chassis Rear-MountedShows the Cisco ASR 1002 Router in a four-post rack Two-Post Rack Installation Installing a Cisco ASR 1002 Router in a Two-Post RackAttach the Cable-Management Bracket Chassis Ground Connection Installation Attaching a Ground Lug to the Chassis Ground Connector Connect the Router to the Network Console and Auxiliary Port Cable ConnectionsManagement Ethernet Port Cable Connection Install the Cables Using the Cable-Management Bracket Connect the Shared Port Adapter CablesConnect AC Power to the Cisco ASR 1002 Router Start the SystemConnect DC Power to the Cisco ASR 1002 Router Output Input FAN FailShows the DC power supply for the Cisco ASR 1002 Router Step Verifying Power Supply operation Start the Cisco ASR 1002 RouterColor Power Up State -Behavior Description Color Behavior Description Page Configuring the Router Using the Console to Access the CLIConfigure Global Parameters Using the Set-up Facility OK? No ip address Tftptimeout Check the Running Configuration Settings Save the Running Configuration to Nvram After InstallationPerform Other Configuration Tasks Power Off the Cisco ASR 1002 Router Replace the Cisco ASR1000-ESP5 or ASR1000-ESP10Replace the Shared Port Adapters Replace a Power Supply in the Cisco ASR 1002 Router Removing an AC Power SupplyAC power cord and service loop Removing the DC Power Supply Installing the DC Power Supply Unit USA

ASR1002 specifications

Cisco Systems ASR1002: An Overview of Main Features, Technologies, and Characteristics

The Cisco ASR1002 router is part of the Aggregation Services Router (ASR) series, renowned for its flexibility and robustness in handling a wide variety of enterprise and service provider applications. Designed for high performance and scalability, the ASR1002 delivers advanced routing capabilities while ensuring efficient resource utilization and minimal operational costs.

One of the standout features of the ASR1002 is its modular architecture. The router supports an extensive range of interfaces and services, allowing organizations to tailor the device to their specific networking requirements. With up to 2GB of onboard memory and the ability to support various WAN technologies, the ASR1002 is well-equipped to handle demanding data workloads.

The ASR1002 offers a performance of up to 2 Gbps of throughput, making it suitable for small to mid-sized businesses needing reliable internet access and robust connectivity. It supports Cisco's Advanced IP Services and offers secure and scalable VPN solutions, enabling organizations to connect multiple sites securely and efficiently.

In addition to its high-speed capabilities, the ASR1002 incorporates advanced security features including Integrated Threat Control, which utilizes Cisco's extensive security technologies to safeguard corporate networks from external and internal threats. It also supports firewall services, intrusion prevention, and secure access protocols, ensuring comprehensive security coverage.

The ASR1002 employs advanced routing technologies like multi-protocol label switching (MPLS) and Border Gateway Protocol (BGP), enabling effective traffic management and seamless integration into existing network infrastructures. This versatility makes it an ideal choice for organizations looking to improve network efficiency and effectiveness.

Another critical characteristic of the ASR1002 is its environmental efficiency. The router is designed with power-saving features and optimizes cooling, contributing to reduced energy costs. With its compact form factor, the ASR1002 can be deployed in various environments without taking up significant space.

Overall, the Cisco ASR1002 stands out as a highly capable and adaptable router, blending advanced features, robust performance, and secure networking capabilities. It caters to the evolving needs of modern enterprises, enabling seamless connectivity and enhancing network reliability. Whether for a small business or a larger enterprise branch, the ASR1002 provides an optimized solution for contemporary networking challenges.