Cisco Systems SN 5428-2 manual Where to Go Next

Page 58

Chapter 2 Installing the SN 5428-2 Storage Router

Where to Go Next

Where to Go Next

Once you have verified that the SN 5428-2 Storage Router hardware is properly installed, it is ready for software configuration. To configure the software, refer to the SN 5428-2 Storage Router Software Configuration Guide.

	Cisco SN 5428-2 Storage Router Hardware Installation Guide
2-32	OL-4797-01

Image 58

Contents Cisco SN 5428-2 Storage Router Hardware Installation Guide Page Cisco SN 5428-2 Storage Router Hardware Installation Guide Page N T E N T S Front-Panel LEDs Cable and Port Pinouts B-1 Viii Audience OrganizationConventions This document uses the following conventionsObtaining Documentation Related DocumentationCisco.com Ordering Documentation Documentation CD-ROMDocumentation Feedback Obtaining Technical Assistance Cisco TAC Website Opening a TAC CaseTAC Case Priority Definitions Obtaining Additional Publications and Information Xvi Product Overview SN 5428-2 Basic Description SN 5428-2 Storage Router ChassisPort Descriptions SN 5428-2 Storage Router Ports10/100 Ethernet Management Port Gigabit Ethernet PortsConsole Port 10/100 Ethernet HA PortFront-Panel LEDs Fibre Channel PortsLED SN 5428-2 Storage Router Software Configuration Fan Assembly Chassis AirflowPower Supply Rear Panel, Power ConnectorOL-4797-01 Installing the SN 5428-2 Storage Router Read Safety Notices Installing the SN 5428-2 Storage Router Read Safety Notices OL-4797-01 Site Planning Installing the SN 5428-2 Chassis Installing on a Table or a ShelfRack-Mounting the SN 5428-2 Storage Router Left RightRear Front Removing Screws from the Sides Assembling the Rack Rails Attaching the Rails to the Rack Sliding the Chassis into the Rack Securing the Chassis to the Rack Attaching the Optional Cable Guide Attaching the Cable GuidesInstalling SFP Modules 10 LC Connector and Fiber-Optic SFP Module Mylar Tab SFP Modules 11 Mylar Tab SFP ModuleActuator/Button SFP Modules 13 Removing a Mylar Tab SFP Module15 Inserting an Actuator/Button SFP Module 16 Removing an Actuator/Button SFP Module from a Port Bale Clasp SFP Modules 17 Bale Clasp SFP Module19 Removing a Bale Clasp SFP Module with Your Index Finger 85667 Connecting to Gigabit Ethernet and Fibre Channel Ports Connecting to a Gigabit Ethernet Port Connecting to a Fibre Channel PortConnecting to the 10/100 Ethernet Management and HA Ports 21 Connecting to the 10/100 Management and HA PortsConnecting to the Console Port Stop Bits Flow ControlConnecting Power 22 Connecting the Console Cable 23 Power Set to Off Verifying Installation Verifying Start-up OperationsVerify That Network Connections Are Operational Verify That Fibre Channel Connections Are OperationalWhere to Go Next Troubleshooting Solving Problems at the Component LevelIdentifying Startup Problems Troubleshooting the Power Supply Troubleshooting a Network or Fibre Channel Port Connection Troubleshooting a Connection to a Gigabit Ethernet PortTroubleshooting Troubleshooting a Connection to a Fibre Channel Port Contacting Customer Service OL-4797-01 Technical Specifications Fuse F1 rating Cable and Port Pinouts Gigabit and Fibre Channel Ports850 62.5 0625 300 m 125 150 m 50.0 500 m 10/100 Ethernet Management and HA Ports Figure B-1 Straight-Through CablesPin Signal Direction Description Console PortRTS OL-4797-01 Numerics IN-2 IN-3 IN-4

Related manuals

Manual 16 pages 56.35 Kb

Manual 22 pages 17.61 Kb

Manual 28 pages 33.75 Kb