Cisco Systems OL-9977-05 manual S c o C o n f i d e n t i a l D r a ft

Page 54

Chapter 2 Mounting Instructions

Mounting the Access Point

C i s c o C o n f i d e n t i a l - D r a ft 1

Caution A readily accessible service disconnect device must be incorporated in the fixed wiring. The disconnect device must open all of the phase conductors.

2.You must protect any AC power plugs and AC receptacles from water and other outdoor elements. You can accomplished by using a UL Listed waterproofing enclosure suitable for covering the AC receptacle and AC power plug that supplies power to the unit as described in Article 406 of the NEC.

3.When you install the access point outdoors or in a wet or damp location, the AC branch circuit that powers the access point should be provided with ground fault protection (GFCI), as required by Article 210 of the National Electrical Code (NEC).

Warning Be very careful when connecting the streetlight adapter to Category 3 pole-top power. If you are not careful, you may electrocute yourself or fall. Statement 363

Note For additional important safety instructions for AC power cords, refer to the AC Power Cords for Cisco Aironet 1500 Series Outdoor Mesh Access Points document that shipped with your AC power cords.

To install an access point on a light pole, follow these steps:

Step 1 When using the streetlight power tap adapter (AIR-PWR-ST-LT-TAP=), ensure that the access point is mounted within 3 ft (1m) of the outdoor light control. For mounting instructions, refer to the “Mounting the Access Point on a Pole” section on page 2-17.

Step 2 Refer to Figure 2-11. The streetlight power tap adapter uses a 3-pronged UL773 twist-lock adapter that is placed between the outdoor light control and its fixture. The UL773 twist-lock adapter is designed to be used with UL773 listed outdoor light controls operating at 100-to 240-VAC, 50/60 Hz.

Step 3 Disconnect the outdoor light control from its fixture.

Step 4 Verify that the voltage available at the fixture is between 100 and 240 VAC, 50/60 Hz. Step 5 Turn off power to the fixture at the designated circuits.

Caution For your safety, when installing the streetlight power tap adapter to the access point AC power connector, always connect the access point end of the cable FIRST. When removing the streetlight power tap adapter, always disconnect the access point end of the cable LAST.

Warning Use the captive connector cap on the unused mil spec connector to prevent water intrusion and possible safety hazards. Statement 362

Step 6 Move the protective cap from the 5-pin AC power connector to the 12-pin Ethernet connector because the Ethernet connector is not used in light pole deployments.

Note Ensure that your antennas are connected to the access point before you apply power to the access point.

Cisco Aironet 1500 Series Outdoor Mesh Access Point Hardware Installation Guide

2-22

OL-9977-05

 

 

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Americas Headquarters Page N T E N T S Mesh Network English Translation B-5 OL-9977-05 Audience PrefaceObjectives OrganizationConventions Bewaar Deze InstructiesSäilytä Nämä Ohjeet Guarde Estas Instruções GEM Disse Anvisninger Viii Related Publications Obtaining DocumentationCisco.com Documentation FeedbackCisco Product Security Overview Product Documentation DVD Ordering DocumentationReporting Security Problems in Cisco Products Product Alerts and Field NoticesObtaining Technical Assistance Cisco Support WebsiteSubmitting a Service Request Finding the Product Serial NumberDefinitions of Service Request Severity Obtaining Additional Publications and InformationPreface Obtaining Additional Publications and Information Xvi Hardware Features, Network Configuration Examples, OverviewHardware Features Access Point ConnectorsConnectors Single or Dual Radio OperationExternal Antennas Multiple Power Sources Part Number Model Gain dBiEthernet Port Network Configuration Examples Metal EnclosureOptional Hardware Wireless Backhaul Point-to-Point BridgingPoint-to-Multipoint Bridging Mesh NetworkTypical Mesh Configuration Using Access Points Typical Layer 3 Access Point Network Configuration Example Layer 2 and Layer 3 Network OperationTypical Layer 2 Access Point Network Configuration Example OL-9977-05 Mounting Instructions Unpacking the Access Point Package ContentsTools and Materials Safety Information FCC Safety Compliance Statement Safety PrecautionsAvoiding Damage to Radios in a Testing Environment Installation Guidelines Site SurveysBefore Beginning the Installation Becoming Familiar with Access Point Installation ComponentsComponents in a Typical Access Point Installation Streetlight Power Tap Adapter Installation Enabling Zero Touch Configuration on the Controller Choose Security MAC Filtering NewMounting the Access Point Configuring a RAPInstallation Options Access Point Mounting Orientations Preferred Horizontal Orientation 5illustrates the access point vertical orientation Access Point Mounting Plate and Carriage Bolts Roof-Overhang Installation Mounting Plate Screw Hole LocationsMounting the Access Point on a Pole Adjustment Plate Attached to the Mounting Plate Pole Clamp and Clamp Adjustment Plate Mounted on a Pole 10 Access Point Attached to the Pole Clamp Grounding the Access Point Streetlight Pole InstallationsS c o C o n f i d e n t i a l D r a ft 11 Using the Streetlight Power Tap Adapter What to Do Next Troubleshooting Guidelines for Using the Access Points Controller MAC Filter ListUsing Dhcp Option Misconfigured Bridge Shared Secret KeyMisconfigured Mesh Access Point IP address Access Point Power Verifying Controller AssociationTranslated Safety Warnings OL-9977-05 Declarations of Conformity Regulatory Information For Home or Office USE Vcci Statement for Japan Industry Canada Canadian Compliance StatementDeclaration of Conformity for RF Exposure Chinese TranslationEnglish Translation Operation of Cisco Aironet Access Points in Brazil Access Point ModelsAccess Point Specifications CCKANSI/IEEE C62.41 Channels and Power Levels OL-9977-05 Connector Pinouts Pin Number Signal NameVDC power + Priming Access Points Prior to Deployment Figure F-1 Typical Priming ConfigurationAppendix F Priming Access Points Prior to Deployment Appendix F Priming Access Points Prior to Deployment OL-9977-05 Configuring Dhcp Option Access Point Vendor Class Identifier VCI OverviewConfiguring Option 43 for 1000 Series Access Points Quotation marks must be includedType + Length + Value Configuring Option 43 for 1500 Series Access Points OL-9977-05 D E IN-2 IN-3 IN-4

OL-9977-05 specifications

Cisco Systems OL-9977-05 is a pivotal reference guide that caters to networking professionals seeking an in-depth understanding of Cisco's infrastructure and certification processes. It encapsulates the essence of modern networking technologies, emphasizing the importance of robust, scalable, and secure network architectures.

One of the primary features of the OL-9977-05 document is its comprehensive overview of Cisco's routing and switching technologies. It covers essential protocols such as OSPF, EIGRP, and BGP, explaining how these dynamic routing protocols contribute to efficient data transmission across diverse networks. Cisco’s focus on interoperability ensures that various systems can communicate smoothly, a critical characteristic in today’s multi-vendor environments.

Security is a cornerstone of Cisco's offerings, and OL-9977-05 delves into advanced security frameworks, including the implementation of firewalls, intrusion prevention systems, and VPNs. It emphasizes the significance of securing both physical and virtual network components to thwart cyber threats. The documentation highlights Cisco's security technologies, such as Cisco Umbrella and Cisco SecureX, providing insights into creating a resilient and secure network.

Another salient feature of the OL-9977-05 is its focus on emerging technologies like software-defined networking (SDN) and network function virtualization (NFV). These technologies represent a paradigm shift in how networks are designed and managed, allowing for more flexible, efficient, and programmable network resources. The guide explores Cisco's innovations in these areas, such as the Cisco ACI and Cisco DevNet, which facilitate the automation and orchestration of network services.

Collaboration and communication tools are also well-covered within the document, highlighting Cisco’s Unified Communications solutions. These tools enhance productivity by enabling seamless communication across various platforms and devices. The integration of cloud services further extends the capabilities of these solutions, aligning with modern business needs.

In conclusion, Cisco Systems OL-9977-05 serves as an essential resource for networking professionals. Its focus on advanced routing and switching, robust security protocols, cutting-edge technologies like SDN and NFV, and collaboration tools provides a holistic view of Cisco's network solutions. This documentation not only supports Cisco certification preparation but also serves as a valuable reference for real-world networking scenarios, ensuring that professionals are well-equipped to tackle the challenges of contemporary network management.
Top Page Image Contents