Cisco Systems OL-9977-05 manual Enabling Zero Touch Configuration on the Controller

Page 42

Chapter 2 Mounting Instructions

Installation Guidelines

C i s c o C o n f i d e n t i a l - D r a ft 1

Adding the Access Point MAC Addresses to the Controller Filter List

Prior to installing your access points, configure your controller by adding the MAC addresses of the access points to the filter list and enable Zero Touch Configuration. This enables the controller to respond to the listed access points and transfer the Bridge Shared Secret Key to each access point. The secret key is required for the access points to communicate with other access points in the same bridge group upon installation. Follow these steps to add a MAC filter entry on the controller:

Step 1 Log into your controller using a web browser.

Step 2 Choose SECURITY > MAC Filtering > New.

Step 3 Enter the MAC address of the access point to the MAC Filter list; for example, 00:0B:91:21:3A:C7. Step 4 Select a WLAN ID or Any WLAN from the WLAN ID pop-up menu.

Step 5 Enter a description (32 characters maximum) of the access point in the Description field; for example, Fisher_Street_00.0B.91.21.3A.C7 shows the location and MAC address of the access point.

Step 6 Choose an interface from the Interface Name pop-up menu and click Apply.

Step 7 Repeat Steps 2 to 6 to add other access points to the list.

Step 8 Log out of your controller and close your web browser.

Enabling Zero Touch Configuration on the Controller

Follow these steps to enable automatic configuration of access points on the controller:

Step 1 Log into your controller using a web browser.

Step 2 Choose WIRELESS > MESH.

Step 3 Check Enable Zero Touch Configuration.

Note If you do not specify a new bridging shared secret key and key format, the default or the existing configured value is used.

Step 4 [Optional] Choose a key format by clicking the down arrow in the Key Format field.

Step 5 [Optional] Enter a new secret key and confirm the entry.

Step 6 Click Apply.

Note You can also use the controller CLI command config network zero-configto enable automatic configuration.

Step 7 Log out from your controller and close your web browser.

Cisco Aironet 1500 Series Outdoor Mesh Access Point Hardware Installation Guide

2-10

OL-9977-05

 

 

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Americas Headquarters Page N T E N T S Mesh Network English Translation B-5 OL-9977-05 Audience PrefaceObjectives OrganizationConventions Bewaar Deze InstructiesSäilytä Nämä Ohjeet Guarde Estas Instruções GEM Disse Anvisninger Viii Related Publications Obtaining DocumentationCisco.com Documentation FeedbackCisco Product Security Overview Product Documentation DVD Ordering DocumentationReporting Security Problems in Cisco Products Product Alerts and Field NoticesObtaining Technical Assistance Cisco Support WebsiteSubmitting a Service Request Finding the Product Serial NumberDefinitions of Service Request Severity Obtaining Additional Publications and InformationPreface Obtaining Additional Publications and Information Xvi Hardware Features, Network Configuration Examples, OverviewHardware Features Access Point ConnectorsConnectors Single or Dual Radio OperationExternal Antennas Multiple Power Sources Part Number Model Gain dBiEthernet Port Network Configuration Examples Metal EnclosureOptional Hardware Wireless Backhaul Point-to-Point BridgingPoint-to-Multipoint Bridging Mesh NetworkTypical Mesh Configuration Using Access Points Typical Layer 3 Access Point Network Configuration Example Layer 2 and Layer 3 Network OperationTypical Layer 2 Access Point Network Configuration Example OL-9977-05 Mounting Instructions Unpacking the Access Point Package ContentsTools and Materials Safety Information FCC Safety Compliance Statement Safety PrecautionsAvoiding Damage to Radios in a Testing Environment Installation Guidelines Site SurveysBefore Beginning the Installation Becoming Familiar with Access Point Installation ComponentsComponents in a Typical Access Point Installation Streetlight Power Tap Adapter Installation Enabling Zero Touch Configuration on the Controller Choose Security MAC Filtering NewMounting the Access Point Configuring a RAPInstallation Options Access Point Mounting Orientations Preferred Horizontal Orientation 5illustrates the access point vertical orientation Access Point Mounting Plate and Carriage Bolts Roof-Overhang Installation Mounting Plate Screw Hole LocationsMounting the Access Point on a Pole Adjustment Plate Attached to the Mounting Plate Pole Clamp and Clamp Adjustment Plate Mounted on a Pole 10 Access Point Attached to the Pole Clamp Grounding the Access Point Streetlight Pole InstallationsS c o C o n f i d e n t i a l D r a ft 11 Using the Streetlight Power Tap Adapter What to Do Next Troubleshooting Guidelines for Using the Access Points Controller MAC Filter ListUsing Dhcp Option Misconfigured Bridge Shared Secret KeyMisconfigured Mesh Access Point IP address Access Point Power Verifying Controller AssociationTranslated Safety Warnings OL-9977-05 Declarations of Conformity Regulatory Information For Home or Office USE Vcci Statement for Japan Industry Canada Canadian Compliance StatementDeclaration of Conformity for RF Exposure Chinese TranslationEnglish Translation Operation of Cisco Aironet Access Points in Brazil Access Point ModelsAccess Point Specifications CCKANSI/IEEE C62.41 Channels and Power Levels OL-9977-05 Connector Pinouts Pin Number Signal NameVDC power + Priming Access Points Prior to Deployment Figure F-1 Typical Priming ConfigurationAppendix F Priming Access Points Prior to Deployment Appendix F Priming Access Points Prior to Deployment OL-9977-05 Configuring Dhcp Option Access Point Vendor Class Identifier VCI OverviewConfiguring Option 43 for 1000 Series Access Points Quotation marks must be includedType + Length + Value Configuring Option 43 for 1500 Series Access Points OL-9977-05 D E IN-2 IN-3 IN-4

OL-9977-05 specifications

Cisco Systems OL-9977-05 is a pivotal reference guide that caters to networking professionals seeking an in-depth understanding of Cisco's infrastructure and certification processes. It encapsulates the essence of modern networking technologies, emphasizing the importance of robust, scalable, and secure network architectures.

One of the primary features of the OL-9977-05 document is its comprehensive overview of Cisco's routing and switching technologies. It covers essential protocols such as OSPF, EIGRP, and BGP, explaining how these dynamic routing protocols contribute to efficient data transmission across diverse networks. Cisco’s focus on interoperability ensures that various systems can communicate smoothly, a critical characteristic in today’s multi-vendor environments.

Security is a cornerstone of Cisco's offerings, and OL-9977-05 delves into advanced security frameworks, including the implementation of firewalls, intrusion prevention systems, and VPNs. It emphasizes the significance of securing both physical and virtual network components to thwart cyber threats. The documentation highlights Cisco's security technologies, such as Cisco Umbrella and Cisco SecureX, providing insights into creating a resilient and secure network.

Another salient feature of the OL-9977-05 is its focus on emerging technologies like software-defined networking (SDN) and network function virtualization (NFV). These technologies represent a paradigm shift in how networks are designed and managed, allowing for more flexible, efficient, and programmable network resources. The guide explores Cisco's innovations in these areas, such as the Cisco ACI and Cisco DevNet, which facilitate the automation and orchestration of network services.

Collaboration and communication tools are also well-covered within the document, highlighting Cisco’s Unified Communications solutions. These tools enhance productivity by enabling seamless communication across various platforms and devices. The integration of cloud services further extends the capabilities of these solutions, aligning with modern business needs.

In conclusion, Cisco Systems OL-9977-05 serves as an essential resource for networking professionals. Its focus on advanced routing and switching, robust security protocols, cutting-edge technologies like SDN and NFV, and collaboration tools provides a holistic view of Cisco's network solutions. This documentation not only supports Cisco certification preparation but also serves as a valuable reference for real-world networking scenarios, ensuring that professionals are well-equipped to tackle the challenges of contemporary network management.
Top Page Image Contents