Cisco Systems 2800 manual Installing the Router, Statement

Page 12

Warning

Warning

Warning

Warning

Warning

Note

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Statement 1032

This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both.

Statement 1043

Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 40 deg. Statement 1047

This product requires surge protection to be provided as part of the building installation. To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety, an external Surge Protective Device (SPD) is required at the AC power service equipment (see definition in the NEC).

Installing the Router

Note Cisco 2800 series routers are normally ordered with modules and interface cards. Before you remove or install any modules or interface cards, see the documents that accompany those items or to the online Cisco 2800 series hardware installation documentation at the following URL:

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/2800/hw/index.htm

For module and interface card compatibility information, see the data sheet for each module and interface card.

Warning

Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord. Statement 1

You can set any Cisco 2800 series router on a desktop or install it in a rack. A Cisco 2811 router can also be mounted on a wall or other flat surface. See the applicable instructions in the following sections.

•Rack-Mounting the Router, page 13

•Wall-Mounting the Router—Cisco 2811 Routers Only, page 16

•Installing the Router on a Desktop, page 17

Caution To prevent damage to the chassis, never attempt to lift or tilt the chassis by the plastic panel on the front. Always hold the chassis by the metal body.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Including License and Warranty Cisco 90-Day Limited Hardware Warranty Terms Duration of Hardware WarrantyReplacement, Repair, or Refund Policy for Hardware To Receive a Return Materials Authorization RMA Number OverviewProduct Serial Number Location Serial Number Label Location for Cisco 2801 RouterDocuments, Equipment, and Tools User DocumentationItems Included with Cisco 2801 Routers Translated VersionsInstall Chassis Safety InformationItems Not Included Page OBS! Spara Dessa Anvisningar Guarde Estas Instruções GEM Disse Anvisninger Page Installing the Router StatementRack-Mounting the Router Attaching Brackets to the Router for Rack-MountingBracket Installation for Front Mounting Installing the Router in a Rack Wall-Mounting the Router-Cisco 2811 Routers Only Attaching Brackets to the Router for Wall MountingInstalling the Router on a Desktop Grounding the ChassisGround during normal use. Statement Chassis Ground Connection on Cisco 2801 Chassis Connect Cables Power Connections Connecting the Router to AC PowerProtective device is rated not greater than 120 VAC, 15 a 240 VAC, 10 A. StatementConnecting the Router to DC Power Size Wire Terminal Lug Protection60 VDC, 20 A. Statement Use copper conductors only. StatementTip Insulation and conductor. StatementStep Be connected first and disconnected last. StatementDC Wire Routing and Attachment for Cisco 2811 Routers Electrical hazards. StatementConnecting to One Source Only-Source a or Source B Source a and Source B Wired with Opposite-Polarity Grounds Connecting the Router to Backup Power WAN, LAN, and Voice ConnectionsPort or Connection Port Type, Color Cable T1/E1 WANPower Up the Router Checklist for Power-UpSystem Management Connections Port Color Connection CablePower-Up Procedure Verify the Hardware Configuration Interface NumberingVerify the Front Panel LED Indications LED Label LED Color or State MeaningSlot Type Interface Numbering Range Port Location Interface Numbering Scheme Examples1Perform Initial Configuration Initial Configuration Using the Setup Command Facility Summary of the available interfaces appears User prompt appears Where to Go Next Verify the Initial ConfigurationTo access documentation on Cisco.com To access documentation using Cisco Connection Online CCOObtaining Documentation Cisco.comProduct Documentation DVD Ordering DocumentationReporting Security Problems in Cisco Products Documentation FeedbackCisco Product Security Overview Submitting a Service Request Definitions of Service Request SeverityObtaining Technical Assistance Cisco Technical Support & Documentation WebsiteObtaining Additional Publications and Information Page Page Page Page USA
Related manuals
Manual 85 pages 32.54 Kb
Top Page Image Contents