Dynex DX-E401 manual Legal notices, Disclaimer

Page 59

Legal notices

59

Dynex’s option). This warranty is available only for the original purchaser of this product. Dynex will not be responsible for any incidental or consequential damages or for any loss arising in connection with the use or inability to use this product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

For defective products purchased online, contact: www.dynexproducts.com Dynex support service at 1-800-305-2204

Legal notices

©2005 Dynex. DYNEX and the DYNEX logo are trademarks of Best Buy Enterprise Services, Inc. Other brands and product names are trademarks or registered trademarks of their respective holders. Specifications and features are subject to change without notice or obligation.

Disclaimer

We make no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed “as is.” Should the programs prove defective following their purchase, the buyer (and not our company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, we reserve the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

Image 59
Contents DX-E401 Introduction ContentsIntroduction to broadband router technology Important safety instructionsBroadband Modem and IP Sharing FeaturesFirewalls LANs and WANsAllows you to assign user-specific access rights Ethernet-based cable or DSL modem System requirements for configurationProduct components Network settings Setting up the routerStart UP and LOG To access the Web-based management utilityWeb-based management utility To use the Setup Wizard Using the Setup WizardIf you selected PPP over Ethernet, go to Step Go to step Setting up the router To access the Web-based configuration utility Configuring the routerHost Name To configure your router to obtain a dynamic IP addressConfiguring a Dynamic IP Address Unless required by your ISP To configure a static IP addressMAC Address Address unless required by your ISPAddress Configuring Pppoe255.255.255.0 OptionalService Name provided by your ISP optional Click the WAN button. The WAN Settings screen opensTo configure PPPoE Re-enter the PPPoE passwordTo configure Pptp To configure BigPond Cable Configuring Your LAN Click the LAN button. The LAN Settings screen opensOr when the connection is dropped To configure your LANLocal domain name. Optional To configure your Dhcp serverConfiguring Your Dhcp Server Lease Time To configure a virtual serverConfiguring a Virtual Server AdvancedAccess the virtual service Name Name referencing the virtual service Private IPBe providing the virtual services Protocol used for the virtual serviceExample #1 To run applications that require multiple connections To configure special applicationsConfiguring Special Applications To configure IP filters Enter the following settings, as appropriateTo block a text string To configure URL blockingConfiguring URL Blocking Enter the following, as appropriate Click URL Blocking, then click EnabledTo configure MAC filtering Configuring MAC FiltersDhcp Client To configure domain blockingConfiguring Domain Blocking Name Filter nameConfiguring Firewall Rules Domains to which access is allowedDomains to which access is blocked To configure Firewall RulesRange Name Name of the firewall ActionIP address of the computer to be in the DMZ To configure the DMZConfiguring the DMZ Tools To configure administrator settingsRemote Port Port number used to access the routerTo configure the system time Configuring the System TimeDay, hour, minute, and second, then click Set Time Click Restore to reset the router to factory settingsTo reload a system settings file To configure the system settingsUpgrading the Firmware You can upgrade the firmware of the routerHard Drive Click Load to reload the fileDownload the new firmware to your hard drive Firmware upgradeTo configure miscellaneous settings Configuring Miscellaneous SettingsPing Test Click Reboot to restart the routerHackers. Click Enabled to block the WAN ping To use the cable tester Refresh StatusLink Status More InfoTo review device information Viewing the LOG To configure the logConfiguring the LOG To view the LogViewing Traffic Statistics Address Email AddressTo view traffic statistics Click the Help tab. The Help screen opens ResetTo reset the system settings to factory defaults HelpTo use the Network Setup Wizard in Windows XP Configuring your computersUsing the Network Setup Wizard in Windows XP Configuring your computers To name your computer Naming your computerConfiguring your computers Click OK to save your changes and exit To check your computer’s IP address Checking your computer’s IP addressTo assign a static IP address Assigning a static IP address in Windows XP and WindowsClick OK to save your changes and exit Selecting a dynamic IP address in Windows XP or Windows To configure your computer to obtain a dynamic IP addressTo assign a static IP address with Macintosh OS Assigning a static IP address with Macintosh OSTo select a dynamic IP address with Macintosh OS Click Apply Now to save your settings and exitSelecting a dynamic IP address with Macintosh OS Go to the Apple menu, then click System PreferencesTroubleshooting TroubleshootingTo use Ipconfig SpecificationsConfirm your computer’s IP configuration Technical Support WarrantyDisclaimer Legal noticesFCC Warning Federal Communications Commission FCC Statement