Dynex DX-E401 manual MAC Address, Address unless required by your ISP, Unless required by your ISP

Page 15

Configuring the router		15

Field	Description

MAC Address	The default MAC address is set to the WAN's physical interface MAC address on
	the broadband router. We do not recommend that you change the default MAC
	address unless required by your ISP.

Clone MAC Address	The default MAC address is set to the WAN's physical interface MAC address on
	the broadband router. You can click Clone MAC Address to copy the MAC
	address of your Ethernet card, or you may be required to enter the MAC address of
	your router. We recommend that you do not change the default MAC address
	unless required by your ISP.

Primary/Secondary	Use this if you do not want to use the one provided by your ISP.
DNS Address

MTU	Use only if required by your ISP. Otherwise, leave the default setting.

CONFIGURING A STATIC IP ADDRESS

Set a static IP address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four numbers (up to three digits each) separated by a dot (x.x.x.x). The router will not accept the IP address if it is not in this format.

To configure a static IP address:

1Open the Configuration menu by following the instructions in To access the Web-based configuration utility: on page 13.

Image 15

Contents DX-E401 Introduction ContentsIntroduction to broadband router technology Important safety instructionsBroadband Modem and IP Sharing FeaturesFirewalls LANs and WANsAllows you to assign user-specific access rights System requirements for configuration Product componentsEthernet-based cable or DSL modem Network settings Setting up the routerTo access the Web-based management utility Web-based management utilityStart UP and LOG To use the Setup Wizard Using the Setup WizardIf you selected PPP over Ethernet, go to Step Go to step Setting up the router To access the Web-based configuration utility Configuring the routerTo configure your router to obtain a dynamic IP address Configuring a Dynamic IP AddressHost Name Unless required by your ISP To configure a static IP addressMAC Address Address unless required by your ISPAddress Configuring Pppoe255.255.255.0 OptionalService Name provided by your ISP optional Click the WAN button. The WAN Settings screen opensTo configure PPPoE Re-enter the PPPoE passwordTo configure Pptp To configure BigPond Cable Configuring Your LAN Click the LAN button. The LAN Settings screen opensOr when the connection is dropped To configure your LANTo configure your Dhcp server Configuring Your Dhcp ServerLocal domain name. Optional Lease Time To configure a virtual serverConfiguring a Virtual Server AdvancedAccess the virtual service Name Name referencing the virtual service Private IPBe providing the virtual services Protocol used for the virtual serviceExample #1 To configure special applications Configuring Special ApplicationsTo run applications that require multiple connections To configure IP filters Enter the following settings, as appropriateTo configure URL blocking Configuring URL BlockingTo block a text string Enter the following, as appropriate Click URL Blocking, then click EnabledTo configure MAC filtering Configuring MAC FiltersDhcp Client To configure domain blockingConfiguring Domain Blocking Name Filter nameConfiguring Firewall Rules Domains to which access is allowedDomains to which access is blocked To configure Firewall RulesRange Name Name of the firewall ActionTo configure the DMZ Configuring the DMZIP address of the computer to be in the DMZ Tools To configure administrator settingsRemote Port Port number used to access the routerTo configure the system time Configuring the System TimeDay, hour, minute, and second, then click Set Time Click Restore to reset the router to factory settingsTo reload a system settings file To configure the system settingsUpgrading the Firmware You can upgrade the firmware of the routerHard Drive Click Load to reload the fileDownload the new firmware to your hard drive Firmware upgradeTo configure miscellaneous settings Configuring Miscellaneous SettingsClick Reboot to restart the router Hackers. Click Enabled to block the WAN pingPing Test To use the cable tester Refresh StatusLink Status More InfoTo review device information Viewing the LOG To configure the logConfiguring the LOG To view the LogAddress Email Address To view traffic statisticsViewing Traffic Statistics Click the Help tab. The Help screen opens ResetTo reset the system settings to factory defaults HelpConfiguring your computers Using the Network Setup Wizard in Windows XPTo use the Network Setup Wizard in Windows XP Configuring your computers To name your computer Naming your computerConfiguring your computers Click OK to save your changes and exit To check your computer’s IP address Checking your computer’s IP addressTo assign a static IP address Assigning a static IP address in Windows XP and WindowsClick OK to save your changes and exit Selecting a dynamic IP address in Windows XP or Windows To configure your computer to obtain a dynamic IP addressTo assign a static IP address with Macintosh OS Assigning a static IP address with Macintosh OSTo select a dynamic IP address with Macintosh OS Click Apply Now to save your settings and exitSelecting a dynamic IP address with Macintosh OS Go to the Apple menu, then click System PreferencesTroubleshooting TroubleshootingSpecifications Confirm your computer’s IP configurationTo use Ipconfig Technical Support WarrantyDisclaimer Legal noticesFCC Warning Federal Communications Commission FCC Statement