Cabletron Systems manual Chapter Troubleshooting, Troubleshooting the HSIM-W85

Page 49

CHAPTER 5

TROUBLESHOOTING

5.1TROUBLESHOOTING THE HSIM-W85

The following sections detail some of the problems encountered in hardware, software, and firmware setups and the possible solutions. If a problem persists, contact Cabletron Systems. Refer to Section 1.8.

5.1.1Hardware Troubleshooting

No LEDs on

Check the host platform to see if it is powered up.

Check that the HSIM-W85 has been connected correctly, that the connectors have no bent pins.

Link (L) LED is OFF

The WAN interface is not configured for operation. Power is off or the HSIM-W85 is not connected properly.

Link (L) LED is RED

The WAN interface is configured, but there is no signal indicating that a valid connection is present on the WAN interface.

Check that the device at the other end of the segment is powered up.

Use management to make sure that both WAN interfaces, local and remote, are configured correctly.

Check to ensure that the correct cable is being used. Refer to Appendix A for details.

Check to ensure that the cable has continuity and is installed correctly.

For back-to-back testing, Cabletron Systems cable part number 9360106 can be used. Another known good HSIM-W85 can be connected using this cable to test the unit.

HSIM-W85 User’s Guide

5-1

Image 49
Contents HSIM-W85 Page HSIM-W85 User’s Guide FCC Notice Vcci Notice HSIM-W85 User’s Guide HSIM-W85 User’s Guide Cabletron Systems Limited Program License Agreement HSIM-W85 User’s Guide Vii Viii HSIM-W85 User’s Guide Contents Contents Firmware Revision Chapter IntroductionImportant Notice Using this Manual Imux OverviewData Flow in the HSIM-W85 FeaturesHdlc ConnectivityPriority Queuing Inverse Multiplexing ImuxLanview Diagnostic LEDs 5 DS1 AlarmSnmp and MIB Support Following conventions are used throughout this document Document ConventionsRelated Documentation Related DocumentationYour email address Getting HelpUnpacking the HSIM-W85 Chapter InstallationInstalling the HSIM-W85 in an Interface Module Installing the HSIM-W85Installing the HSIM-W85 Installing the HSIM-W85 Installing the HSIM-W85 in a Standalone Device Figure B-3 HSIM-W85 Cable Connection Connecting the HSIM-W85 to the NetworkLanview Leds ChapterLanview LEDs Local Management Chapter ManagementManagement Network Tools Commands Network Tools Help Screen Command Imux Built-in CommandsExample Wanpq WanpqSyntax ds1alarm Ds1alarmDsx1 Ds1alarmDsx1 Syntax ds1ext Ds1extDone, quit, exit Special Commands3shows the imux setup for group id 1 so far Sample Imux ConfigurationEnabling the Imux Group Sample Imux Configuration Management HSIM-W85 User’s Guide Troubleshooting the HSIM-W85 Chapter TroubleshootingHardware Troubleshooting Status S LED is OFF Problems with the Firmware Image Investigating Software Configuration ProblemsHSIM-W85 User’s Guide Physical Properties Appendix a SpecificationsRegulatory Compliance Environmental RequirementsAppendix B Typical Configuration Appendix B Typical Configuration Port ID Appendix C FCC Part 68 USER’S InformationAppendix C FCC Part 68 User’s Information Being duly sworn, state My commission expires

W85 specifications

Cabletron Systems W85 is a prominent networking solution that was developed to support the burgeoning demand for high-performance data communications in the enterprise environment. As an advanced multi-layer switch, the W85 effectively integrates various networking technologies, offering robust support for both wired and wireless connectivity, making it particularly suitable for complex network infrastructures.

One of the standout features of the W85 is its scalability. Designed to grow with the needs of a business, the W85 can accommodate an increasing number of users and devices without sacrificing performance. This is essential in today's digital workspace, where employees and equipment are continually being added to the network.

The W85 operates across multiple layers of the OSI model, offering Layer 2 and Layer 3 switching capabilities. Layer 2 functionalities enable efficient Ethernet switching and VLAN support, ensuring that data can move swiftly within local networks. Meanwhile, its Layer 3 capabilities facilitate dynamic routing, allowing for intelligent data distribution across different network segments. This dual functionality enhances the W85's versatility, making it suitable for both small and large-scale deployments.

Equipped with advanced security features, the Cabletron W85 places a strong emphasis on network integrity. It supports comprehensive security protocols that help to mitigate potential threats. Features such as Access Control Lists (ACLs) allow administrators to define and enforce security policies, ensuring that only authorized users have access to sensitive data. Furthermore, the device supports advanced encryption methods to protect data in transit, which is crucial for safeguarding information in modern enterprises.

The W85 is also notable for its management capabilities. It provides an intuitive web-based interface for system administrators, simplifying the configuration and monitoring processes. With support for SNMP (Simple Network Management Protocol), administrators can efficiently manage network devices and receive alerts for potential issues before they escalate into significant problems.

In terms of connectivity, the Cabletron W85 features multiple Gigabit Ethernet ports designed to handle high-speed data transfer. This allows for seamless integration with existing infrastructure while ensuring that performance remains high even under heavy loads. The device is also compatible with various network management protocols, positioning it as a streamlined component in any enterprise’s networking strategy.

The Cabletron Systems W85 embodies the future of enterprise networking with its combination of scalability, security features, and robust management tools, ensuring it remains a relevant choice for organizations looking to enhance their networking capabilities.