Cabletron Systems manual 100BASE-T PIN Assignments, Connectors

Page 94

Technical Speciﬁcations

Table A-2. DB9 Pin Assignments

ELS100-16TX RJ45 (female)		DB9 pin (female)

Pin 1	(Rx)	Pin 2

Pin 4	(Tx)	Pin 3

Pin 5	(GND)	Pin 5

A.3 100BASE-T PIN ASSIGNMENTS

An Ethernet twisted-pair link segment requires two pairs of wires. Each wire pair is identiﬁed by solid and striped colored wires. For example, one wire in the pair might be red and the other wire, red with white stripes.

Connectors

Refer to the diagram below and note how the pins are numbered. Be sure to hold the connectors in the same orientation when connecting the wires to the pins.

		8
	1	8
	1	1
		1

Figure A-1. Connector Pin Numbers

Each twisted-pair link segment must have a male connector attached to both ends. According to the 100BASE-T speciﬁcation, pins 1 and 2 on the connector are used for receiving data; pins 3 and 6 are used for transmitting data, as shown in Table A-3.

A-4

Image 94

Contents

User Guide Page FCC Notice DOC Notice Cabletron Software Program License Declaration of Conformity Contents ELS100-16TX Diagnostics Troubleshooting Monitoring and Managing Your ELS100-16TXAppendix a Technical Specifications Appendix B GlossaryContents Viii Chapter Introduction About this Manual Getting Help Your email addressDocument Conventions Related Documentation Overview ELS100-16TX Front PanelSmartSTACK 100 ELS100-16TX Architecture Introduction Port Trunking AutonegotiationStore and Forward Switching Discarding Local TrafﬁcTypical Switching Application Spanning Tree AlgorithmSmartSTACK 100 ELS100-16TX Bridge Address Table SmartSTACK 100 ELS100-16TX Port Mirroring SmartSTACK 100 ELS100-16TX Sample ApplicationsSmartSTACK 100 ELS100-16TX Trunking Virtual Workgroups SmartSTACK 100 ELS100-16TX Trunking with 100 Mbps PortsRepeater Traffic Workgroup a Workgroup B Local Console Manager Command Syntax Conventions Basic LCM Commands HelpELS100-16TX Local Console Manager Exit or Logout EraseTraplog Introduction Chapter Unpacking and Installing Your ELS100-16TX ELS100-16TX Front PanelPort LEDs 100BASE-T Epim Ports Reset Switch Status LEDs ACT Installing AN Epim Describes the ELS100-16TX buttonsInstalling an Epim Installing the ELS100-16TX Rack-Mounting an ELS100-16TXAttaching Rackmount Brackets Checking the POWER-UP Diagnostics Sequence Connecting the Local Console ManagerConnecting to the Network Connecting UTP Cables ELS100-16TX Twisted Pair ConnectionConnecting a Segment to the EPIM-100FX Cable Pinouts RJ45 Crossover CableFiber Optic Network Connection EPIM-100FX Port Unpacking and Installing Your ELS100-16TX Chapter Configuring Your ELS100-16TX Spectrum Spel SpmaAssigning IP Addresses Type ipaddr PORT-NUMBER IP Address Deleting an IP Address Displaying IP AddressesChanging a Subnet Mask Enabling Bridging To change the subnet mask, at the LCM promptDisabling Bridging Displaying Bridging FunctionsEnabling Trunking Trunk Groups 100BASE-T Crossover CablesTrunk Groups Disabling Trunking Displaying Trunking Status Display could look like the followingEnabled, Rip listening Enabling Port Mirroring Disabling MirroringDisplaying Mirroring Status To check the status for ports conﬁgured for mirroring Defining and Deleting Workgroups Deﬁning Virtual WorkgroupsLCM responds with the following display Assigning a Community Name Configuring BROADCAST/MULTICAST Storm Protection Modifying MIB Variables System ContactSystem Location System NameCommunity Names Set Community Name Aging ParameterELS100-16TX Management Tools Chapter Monitoring and Managing Your ELS100-16TXELS100-16TX Statistics Gathering Statistics System StatisticsEthernet Port Statistics Using LCM to Check ELS100-16TX Status Displaying StatusEnabled, Rip listening Displaying MAC Addresses To display all MAC addresses, at the LCM prompt Displaying Manufacturing Information LCM would displayUsing LCM to Manage the ELS100-16TX Managing the ELS100-16TXDisabling a Port Enabling a PortNoRIP Option Changing a Community Name Setting the Baud Rate Setting a Reboot Time POWER-UP Diagnostics Chapter ELS100-16TX Diagnostics and TroubleshootingPower-up LED Sequence Speciﬁc Power-up Tests Software Checksum ComparisonResponses to Failures AT POWER-UP Power-up Diagnostics ResultsStatus and Activity Indicators ELS100-16TX Front Panel LEDs ACT ELS100-16TX does not Power UP 2 ELS100-16TX Has Rebooted Connectivity Problems3 ELS100-16TX Does Not Respond to NMS ELS100-16TX Diagnostics and Troubleshooting Electrical Connector PortsPhysical EnvironmentalDiagnostic LEDs Standard SupportRegulatory Compliance Address Table SizeManagement Support Serial Cable PIN AssignmentsConnectors 100BASE-T PIN AssignmentsSTRAIGHT-THROUGH Wiring Crossover WiringEPIM-100FX Specifications 5 4 3 RuleCable Type Worst Case Budget Typical Budget Technical Speciﬁcations Address table AlarmAddress AgentBpdu bridge protocol data unit BackboneBandwidth Bps bits per secondDatagram CongestionData link layer Data rate or speedEncode Full wire speedEncapsulation EntityIeee Intelligent bridge/switchIcmp Internet control message protocol InitializationIP Internet protocol InternetworkingInteroperability ISO International Standards OrganizationMbps megabits per second MAC media access controlMask MIB management information baseOSI Open Systems Interconnection Power budgetPropagation delay PacketProtocol Rarp reverse address resolution protocolService Protocol suiteSynchronous transmission SwitchSymbol Translating bridgeUpstream WAN wide area networkGlossary