Cabletron Systems 100 manual Command Syntax Conventions

Page 28

Introduction

1.6.1 Command Syntax Conventions

The following conventions apply as you use LCM commands:

•Press the Enter key to execute a command after you type it in.

•A port range is either a single port number, or a list of port numbers separated by commas or hyphens. For example, 3 is port 3; 3,7 are ports 3 and 7; 3-5are ports 3,4, and 5; and 3-5,7are ports 3,4,5, and 7.

•To quit any command, press the Control-C keys (^C or Ctrl-C).

•You can abbreviate any command where there is no ambiguity; if there is ambiguity, LCM responds with an error message.

•Commands are not case sensitive.

•Invalid commands or misspellings returns an error message.

•The previous command can be repeated by typing !!

•MAC addresses are displayed in little-endian Ethernet (least signiﬁcant bit) bit order, with each octet separated by a colon. For example:

ELS100-16 >address 00:40:27:04:1a:0f

•Information that you need to enter with an LCM command is enclosed in square brackets [ ]. For example, you must enter a

port number and an IP address to execute the ipaddr [PORT- NUMBER] [IP ADDRESS] command:

ELS100-16 >ipaddr 6 192.138.217.40

•Parameters that appear in all capital letters, for example bridge [PORT-RANGE], indicate that you must enter a value for that parameter. If a string of parameters is displayed between braces, for example [{offonnoBPDU}], you must select one of the displayed options. For example, if you wanted to enable bridging on a port, or a range of ports, you would enter:

ELS100-16 >bridge 2-4 on

1-18

Image 28

Contents User Guide Page FCC Notice DOC Notice Cabletron Software Program License Declaration of Conformity Contents ELS100-16TX Diagnostics Troubleshooting Monitoring and Managing Your ELS100-16TXAppendix a Technical Specifications Appendix B GlossaryContents Viii Chapter Introduction About this Manual Getting Help Your email addressDocument Conventions Related Documentation Overview ELS100-16TX Front PanelSmartSTACK 100 ELS100-16TX Architecture Introduction Port Trunking AutonegotiationStore and Forward Switching Discarding Local TrafﬁcTypical Switching Application Spanning Tree AlgorithmSmartSTACK 100 ELS100-16TX Bridge Address Table SmartSTACK 100 ELS100-16TX Port Mirroring SmartSTACK 100 ELS100-16TX Sample ApplicationsSmartSTACK 100 ELS100-16TX Trunking Virtual Workgroups SmartSTACK 100 ELS100-16TX Trunking with 100 Mbps PortsRepeater Traffic Workgroup a Workgroup B Local Console Manager Command Syntax Conventions Basic LCM Commands HelpELS100-16TX Local Console Manager Exit or Logout EraseTraplog Introduction Chapter Unpacking and Installing Your ELS100-16TX ELS100-16TX Front PanelPort LEDs 100BASE-T Epim Ports Reset Switch Status LEDs ACT Installing AN Epim Describes the ELS100-16TX buttonsInstalling an Epim Installing the ELS100-16TX Rack-Mounting an ELS100-16TXAttaching Rackmount Brackets Checking the POWER-UP Diagnostics Sequence Connecting the Local Console ManagerConnecting to the Network Connecting UTP Cables ELS100-16TX Twisted Pair ConnectionConnecting a Segment to the EPIM-100FX Cable Pinouts RJ45 Crossover CableFiber Optic Network Connection EPIM-100FX Port Unpacking and Installing Your ELS100-16TX Chapter Configuring Your ELS100-16TX Spectrum Spel SpmaAssigning IP Addresses Type ipaddr PORT-NUMBER IP Address Deleting an IP Address Displaying IP AddressesChanging a Subnet Mask Enabling Bridging To change the subnet mask, at the LCM promptDisabling Bridging Displaying Bridging FunctionsEnabling Trunking Trunk Groups 100BASE-T Crossover CablesTrunk Groups Disabling Trunking Displaying Trunking Status Display could look like the followingEnabled, Rip listening Enabling Port Mirroring Disabling MirroringDisplaying Mirroring Status To check the status for ports conﬁgured for mirroring Defining and Deleting Workgroups Deﬁning Virtual WorkgroupsLCM responds with the following display Assigning a Community Name Configuring BROADCAST/MULTICAST Storm Protection Modifying MIB Variables System ContactSystem Location System NameCommunity Names Set Community Name Aging ParameterELS100-16TX Management Tools Chapter Monitoring and Managing Your ELS100-16TXELS100-16TX Statistics Gathering Statistics System StatisticsEthernet Port Statistics Using LCM to Check ELS100-16TX Status Displaying StatusEnabled, Rip listening Displaying MAC Addresses To display all MAC addresses, at the LCM prompt Displaying Manufacturing Information LCM would displayUsing LCM to Manage the ELS100-16TX Managing the ELS100-16TXDisabling a Port Enabling a PortNoRIP Option Changing a Community Name Setting the Baud Rate Setting a Reboot Time POWER-UP Diagnostics Chapter ELS100-16TX Diagnostics and TroubleshootingPower-up LED Sequence Speciﬁc Power-up Tests Software Checksum ComparisonResponses to Failures AT POWER-UP Power-up Diagnostics ResultsStatus and Activity Indicators ELS100-16TX Front Panel LEDs ACT ELS100-16TX does not Power UP 2 ELS100-16TX Has Rebooted Connectivity Problems3 ELS100-16TX Does Not Respond to NMS ELS100-16TX Diagnostics and Troubleshooting Connector Ports PhysicalElectrical EnvironmentalDiagnostic LEDs Standard SupportAddress Table Size Management SupportRegulatory Compliance Serial Cable PIN AssignmentsConnectors 100BASE-T PIN AssignmentsSTRAIGHT-THROUGH Wiring Crossover WiringEPIM-100FX Specifications 5 4 3 RuleCable Type Worst Case Budget Typical Budget Technical Speciﬁcations Alarm AddressAddress table AgentBackbone BandwidthBpdu bridge protocol data unit Bps bits per secondCongestion Data link layerDatagram Data rate or speedFull wire speed EncapsulationEncode EntityIntelligent bridge/switch Icmp Internet control message protocolIeee InitializationInternetworking InteroperabilityIP Internet protocol ISO International Standards OrganizationMAC media access control MaskMbps megabits per second MIB management information basePower budget Propagation delayOSI Open Systems Interconnection PacketRarp reverse address resolution protocol ServiceProtocol Protocol suiteSwitch SymbolSynchronous transmission Translating bridgeUpstream WAN wide area networkGlossary