Installing the Module

SMARTSTACK FAST ETHERNET SWITCH

STACKING MODULE

Cabletron’s ELS100-STACK Stacking Module can be used to stack up to four ELS100-S24TX2M switch units. Running at a bandwidth of over 4 Gbps, these modules provide a common interface to the attached switches, allowing the stack to function and be managed as a single device.

System and Port Status LEDs

LEDs are provided on the front panel of the switch. These LEDs can be used to verify if the stack is functioning properly. The following table details the indicator functions provided by the ELS100-S24TX2M:

Port and System Status LEDs

LED	Condition	Status

Power	On	Switch is receiving power.

RDP	On	Redundant power is on, and in
		backup or active mode.

	Off	Redundant power is off or has failed.

Mgmt	On	Agent is operational.

RJ-45 Ports

Link	On	Port has established a valid network
		connection

	Yellow	Valid 10 Mbps connection.

	Green	Valid 100 Mbps connection.

	Flashing	Port has been partitioned due to an
		abnormal network condition, or
		manually disabled.

Activity1	On	Traffic is passing through the port.

FDX1	On	Port has been set to full duplex.

FC1	On	Flow control enabled.

Module Ports

Status	On	A module is installed in this slot.

Activity	Flashing	Traffic is passing through the port

1:Use the Mode Select button to select LED display mode.

2:There is no LED for indicating stacking status.

CAUTION: The ELS100-STACK Stacking Module is designed for ELS100-S24TX2M switches only. Do not try to install these modules in any other units.

The ELS100-STACK Stacking Module installs in the lower-left slot on the rear panel of the ELS100- S24TX2M switch. Do not install this module in any other slot. To install the module, follow the instructions below.

Equipment Checklist

After unpacking the Stacking Module, check the contents of the box to be sure you’ve received the following items:

•One ELS100-STACK Stacking Module

•One Stacking Cable

•This document

Handling the Module

CAUTION: The ELS100-STACK Stacking Module can easily be damaged by electrostatic discharge.

To prevent electrostatic damage, observe the following guidelines:

•Do not remove the module from its packaging until you are ready to install it.

•Do not touch any of the module’s pins, connectors or components.

•Hold the module only by its edges or front panel.

•Wear an anti-static wristband connected to a suitable earth ground whenever handling the module.

•Store or transport this module only in appropriate anti-static packaging.

Instructions

CAUTION: The switch must be powered off before installing or replacing any module.

1.Power off the switch: Disconnect the AC power cord from the switch. If a redundant power unit (RPU) is present, disconnect its DC cable connection to the switch.

2.Remove network cables: If you are replacing a module, remove the cable attached to the port on the module.

3.Loosen the screws on the installed module or slot faceplate: Using your fingers or a flathead screwdriver, turn the screws securing the module (or faceplate) in the lower-left slot in a counter- clockwise direction until they are free of the chassis. Be sure not to completely remove the screws from the module or faceplate.

4.Remove the installed module or faceplate: Firmly pull on the screws until the module is free of the switch. Carefully slide the module straight out of the slot.

Keep the original faceplate for future use. If you should remove the module, replace the faceplate to prevent dust and debris from entering the unit and to maintain proper air flow.

5.Insert the new module into the switch: Holding the new module with the text on the front panel upright, carefully slide the module into the switch slot and press gently until it snaps into place. Be sure the new module’s front panel is flush with the switch panel.

6.Secure the new module: Secure the new module in place by screwing the attached screws clockwise into the switch’s chassis. Tighten them enough to secure the module, but not so tight as to prevent them from being unscrewed by hand.

7.Connect the stack cables: Attach one end of the stacking cable to the stack connector labeled “DOWN” on the top device, and the other end to the connector labeled “UP” on the next lower device. Repeat this step until all the devices have been connected.

8.Power on the switch: Reconnect the previously removed power sources to the switch. (Note that the Management Module in the bottom switch will become the master.) The front-panel LEDs on the switches should indicate their status. Refer to the table of LEDs in this guide for a description of the LED indications. If the stack is not functioning properly, see “Troubleshooting” below.

More details concerning connection options and network applications can be found in the ELS100-S24TX2M Installation Guide. Information on managing the stack can be found in the Management Guide that is included with the base unit.

TROUBLESHOOTING

If you experience any problems with the module, check the following items before contacting Cabletron’s Technical Support:

•Ensure that all the switches in the stack are powered up.

•Ensure that the devices attached to the stack are powered up and operating correctly.

•Ensure that the Stacking Modules are properly seated in their slots.

•Check the connectors on both ends of the stack cable to be sure they are properly engaged. Tighten the thumb screws on the cable connectors to ensure a good connection.

ELS100-S24TX2M specifications

The Cabletron Systems ELS100-S24TX2M is a highly regarded Ethernet switch that has made a significant mark in the networking landscape. Designed for robust performance and reliability, this modular switch features 24 Ethernet ports, all of which are 10/100BASE-TX capable, allowing for seamless integration with existing network infrastructures.

One of the key features of the ELS100-S24TX2M is its scalability. It supports various expansion modules, enabling organizations to adapt the switch to meet evolving networking needs. This modularity allows IT managers to add additional ports or functionality without the need for a complete hardware overhaul.

The ELS100-S24TX2M also incorporates advanced switching technologies, including Store-and-Forward and cut-through switching modes. Store-and-Forward ensures that incoming packets are checked for errors before being forwarded, dramatically enhancing data integrity and reducing transmission errors. Cut-through switching, on the other hand, provides low latency forwarding of packets by sending them as soon as the destination address is recognized. This dual-mode capability makes the ELS100-S24TX2M suitable for both high-performance applications and general networking tasks.

Another noteworthy aspect of the ELS100-S24TX2M is its support for Quality of Service (QoS) mechanisms. This feature prioritizes time-sensitive data, such as voice or video traffic, ensuring smooth and uninterrupted communication. With the rise of VoIP and streaming services, this capability is increasingly essential for maintaining high-level service standards.

In terms of network management, the ELS100-S24TX2M offers several useful tools. SNMP support facilitates remote monitoring and management, allowing network administrators to gain insights into traffic patterns and overall system performance. The device also supports web-based management, making it user-friendly and accessible.

Moreover, the build quality and reliability of the Cabletron Systems ELS100-S24TX2M are notable. Designed for durability, it incorporates features that address thermal issues, ensuring consistent performance even in demanding environments.

In summary, the Cabletron Systems ELS100-S24TX2M stands out due to its impressive combination of modularity, performance features, and advanced networking capabilities. Its focus on QoS, management tools, and solid construction makes it a versatile choice for businesses looking to enhance their network infrastructure for the present and future.

SMARTSTACK FAST ETHERNET SWITCH

STACKING MODULE

System and Port Status LEDs

LED

Condition

Status

RDP

FC1