Cabletron Systems ELS10-26TX manual FE-100TX Crossover Switch

Page 44

Unpacking and Installing Your ELS10-26

determine if the wires have been crossed over for the proper connection.

A schematic of a crossover cable is shown in Figure 2-6. If the wires do not cross over, use the switch on the FE-100TX to internally cross over the RJ45 port. Figure 2-7 shows how to properly set the FE-100TX crossover switch.

Position =

(not crossed over)

1. TX+ 5. NC

2. TX- 6. RX-

3.RX+ 7. NC

4.NC 8. NC

=

x

10

100

FE-100TX

Position X (crossed over)

1.RX+ 5. NC

2.RX- 6. TX-

3.TX+ 7. NC

4.NC 8. NC

166505

Figure 2-7. FE-100TX Crossover Switch

Connect an FE-100TX to a twisted pair segment as follows:

1.Ensure that the device at the other end of the segment is connected to the segment and is powered ON.

2.Connect the twisted pair segment to the module by inserting the RJ45 connector on the twisted pair segment into the RJ45 port on the module. See Figure 2-7.

3.Verify that a Link exists by checking that the port LINK LED is on (solid green). If the LINK LED is off, perform the following steps until it is on:

a.Check that the 100BASE-TX device at the other end of the twisted pair segment is powered up.

b.Verify that the RJ45 connector on the twisted pair segment has the proper pinouts.

c.Check the cable for continuity.

2-12

Page 43 Page 45
Image 44
Page 43 Page 45
Contents ELS10-26 User Guide Page FCC Notice DOC Notice Cabletron Software Program License Declaration of Conformity Contents Contents Monitoring and Managing Your ELS10-26Appendix B Glossary ELS10-26 Diagnostics and TroubleshootingAppendix a Technical Specifications Contents Viii Chapter Introduction About this Manual Getting Help BBSDocument Conventions Related Documentation Overview ELS10-26TX Front PanelSmartSTACK 10 ELS10-26 Architecture Store and Forward Switching OSI Reference ModelTypical Switching Application Discarding Local TrafficSpanning Tree Algorithm SmartSTACK 10 ELS10-26 Bridge Address TableIntroduction SmartSTACK 10 ELS10-26 Sample Applications SmartSTACK 10 ELS10-26 Port MonitoringPacket Capturing and Monitoring SmartSTACK 10 ELS10-26 Trunking SmartSTACK 10 ELS10-26 Trunking with 10 Mbps PortsSmartSTACK 10 ELS10-26 Fast Ethernet SmartSTACK 10 ELS10-26 Backbone ConfigurationSmartSTACK 10 ELS10-26 Trunking with 100 Mbps Ports Virtual Workgroups Traffic Workgroup a Workgroup B Local Console Manager Command Syntax Conventions Basic LCM Commands HelpELS10-26 Local Console Manager Traplog EraseExit or Logout Chapter Unpacking and Installing Your ELS10-26 ELS10-26 Front PanelReset Switch Status LEDs ACT Installing AN Fepim Describes the ELS10-26 buttonsInstalling an Fepim Installing the ELS10-26 Rack-mounting an ELS10-26Attaching Rackmount Brackets Checking the POWER-UP Diagnostics Sequence Connecting the Local Console Manager Connecting to the NetworkConnecting UTP Cables 10BASE-T/ 100BASE-TXConnecting a UTP Segment to the FE-100TX Cable Pinouts RJ45 Crossover CableFE-100TX Crossover Switch Connecting a Multimode Segment to the FE-100FX Fiber Optic Network ConnectionFE-100FX Port Unpacking and Installing Your ELS10-26 Unpacking and Installing Your ELS10-26 Chapter Configuring Your ELS10-26 Spectrum Spel SpmaAssigning IP Addresses Type ipaddr PORT-NUMBER IP Address Changing a Subnet Mask Displaying IP AddressesDeleting an IP Address Enabling Bridging To change the subnet mask, at the LCM promptDisabling Bridging Displaying Bridging FunctionsEnabling Trunking Trunk Groups Trunk ConnectionsTrunk Groups Disabling Trunking Displaying Trunking Status Display could look like the followingEnabled, Rip listening Enabling Port Monitoring Disabling Monitoring Displaying Monitoring StatusEnabled, Rip listening Defining and Deleting Workgroups Defining Virtual WorkgroupsLCM responds with the following display Assigning a Community Name Configuring BROADCAST/MULTICAST Storm Protection Modifying MIB Variables System ContactCommunity Names System NameSystem Location Set Community Name Aging ParameterELS10-26 Statistics Chapter Monitoring and Managing Your ELS10-26ELS10-26 Management Tools Gathering Statistics System StatisticsEthernet Port Statistics Using LCM to Check ELS10-26 Status Displaying StatusEnabled, Rip listening Displaying MAC Addresses To display all MAC addresses, at the LCM prompt Displaying Manufacturing Information LCM would displayUsing LCM to Manage the ELS10-26 Managing the ELS10-26Disabling a Port Enabling a PortNoRIP Option Changing a Community Name Setting the Baud Rate Setting a Reboot Time Power-up LED Sequence Chapter ELS10-26 Diagnostics and TroubleshootingPOWER-UP Diagnostics Specific Power-up Tests Software Checksum ComparisonStatus and Activity Indicators Power-up Diagnostics ResultsResponses to Failures AT POWER-UP ELS10-26 Front Panel LEDs LED Connectivity Problems TroubleshootingELS10-26 does not Power UP 2 ELS10-26 Has Rebooted 3 ELS10-26 Does Not Respond to NMSELS10-26 Diagnostics and Troubleshooting Appendix a Technical Specifications ELS10-26 Specifications Connector PortsPhysical ElectricalStandard Support Diagnostic LEDsEnvironmental Address Table Size Management SupportRegulatory Compliance Serial Cable PIN AssignmentsConnectors 10BASE-T PIN AssignmentsSTRAIGHT-THROUGH Wiring Pin Assignment aCrossover Wiring 5 4 3 RuleFE-100FX Fepim SpecificationsFE-100TX Cable Type Worst Case Budget Typical Budget Alarm AddressAddress table AgentBackbone BandwidthBpdu bridge protocol data unit Bps bits per secondCongestion Data link layerDatagram Data rate or speedFull wire speed EncapsulationEncode EntityIntelligent bridge/switch Icmp Internet control message protocolIeee InitializationInternetworking InteroperabilityIP Internet protocol ISO International Standards OrganizationMAC media access control MaskMbps megabits per second MIB management information basePower budget Propagation delayOSI Open Systems Interconnection PacketRarp reverse address resolution protocol ServiceProtocol Protocol suiteSwitch SymbolSynchronous transmission Translating bridgeUpstream WAN wide area networkGlossary Index NumericsIndex RIP Wiring crossover A-6 Straight-through A-5

ELS10-26TX specifications

Cabletron Systems ELS10-26TX is a high-performance Ethernet switch designed to meet the demands of expanding network architectures. This switch is particularly noted for its robust features, making it suitable for various applications, from small business environments to larger enterprise settings.

One of the main features of the ELS10-26TX is its ability to support 10/100 Mbps auto-sensing Ethernet connections. This versatility allows it to interface seamlessly with existing networks, accommodating both older systems and newer high-speed devices. Its 26 ports provide ample connectivity for a range of devices, enabling users to connect multiple workstations, printers, and servers without any compromise on network performance.

The ELS10-26TX utilizes advanced switching technology, which enables it to dynamically manage data traffic across all connected devices. By employing store-and-forward switching techniques, the device reduces latency while preventing data collisions. This is particularly beneficial in environments where heavy traffic is common, as it ensures reliable communication and efficient data transfer.

In terms of its physical characteristics, the ELS10-26TX features a compact design that allows for easy integration into existing network setups. Its robust hardware ensures durability and longevity, making it a reliable choice for organizations that require uninterrupted network service. Additionally, it supports rack-mountable installation, providing flexibility for various deployment scenarios.

The switch also includes essential management features, such as VLAN support, which allows organizations to segment their networks for improved security and traffic management. With Quality of Service (QoS) capabilities, the ELS10-26TX can prioritize critical data traffic, ensuring that essential applications receive the necessary bandwidth for optimal performance.

Security is another notable characteristic of the ELS10-26TX. The device incorporates several security measures to protect the network from unauthorized access and potential threats. These include port security features, which restrict access to individual switch ports, and network management tools that facilitate monitoring and auditing of network activity.

In summary, the Cabletron Systems ELS10-26TX is a versatile and feature-rich Ethernet switch that can significantly enhance network connectivity and performance. Its combination of speed, management capabilities, and security features makes it suitable for a wide array of network configurations, ensuring that it meets the evolving needs of organizations today and into the future.
Top Page Image Contents